Vista 5237 User manual

INSTALLATION INSTRUCTIONS Up and Accent Lights
FOR USE ONLY WITH LOW VOLTAGE LANDSCAPE POWER UNITS THAT DO NOT EXCEED 25 AMPS, 15 VOLT MAXIMUM.
WARNING: Luminaires must be installed in accordance with the National Electrical Code (NEC) and local codes.
Failure to do so will void the warranty and may result in serious injury and/or damage to the luminaire.
SAFETY WARNING: Luminaire can become very hot depending on lamp wattage used. Lens and metal around lamp
can become hot enough to blister hands. Particular care should be taken not to locate luminaires where small children
can reach them if high wattage lamps are used.
SUBJECT TO LOCAL CODE, WHICH IS GOVERNING, LUMINAIRES ARE NOT TO BE INSTALLED WITHIN 10 FT. (3.05M) OF A
POOL OR SPA. SECONDARY CABLE IS NOT TO BE BURIED MORE THAN 6”. WHEN USING MULTIPLE LUMINAIRES, LOAD IS NOT
TO EXCEED THE TOTAL WATTS OF TRANSFORMER RATING. DO NOT USE EXTENSION CORDS ON POWER UNITS.
NOTE: Always use UL recognized wire connectors for connections.
NOTE: Save these instructions for future reference.
LUMINAIRE IS UL LISTED FOR ABOVE GROUND INSTALLATION ONLY.
LUMINAIRE MOUNTING (with ground stake):
1. To prevent electrical shock, disconnect transformer from
electrical supply before installation or service.
2. Run wire pigtail from luminaire through the mounting hole
in top of ground stake.
3. Thread luminaire into threaded hole in ground stake.
4. Place stake in desired position and insert into ground until
flange of stake is flush to grade.
5. Strip the (2) leads from the luminaire pigtail wire. Using the
two (2) silicone lled safety connectors (provided),
connect the leads from the luminaire to the main supply
cable leads.
NOTE: Luminaires are supplied with 36” of 18-2 cable pigtail
for secure connection to the main supply cable. The
wire is to be protected by routing in close proximity to the
luminaire. The wiring should be buried a maximum depth
of 6 inches (15.2 cm) in order to connect to the main
supply cable.
6. Aim luminaire to desired angle. Lock into place by
tightening phillips screw in adjustable knuckle.
NOTE: Avoid aiming fixture directly upward. Whenever
possible, set at angle to prevent rain or irrigation water
from settling on lens.
1625 Surveyor Avenue •Simi Valley, CA 93063 •[phone] •(800) 766-VISTA (8478)
FAX: (888) 670-VISTA (8478) • [email protected] • www.vistapro.com
12V SERIES
5237

1625 Surveyor Avenue •Simi Valley, CA 93063 •[phone] •(800) 766-VISTA (8478)
FAX: (888) 670-VISTA (8478) • [email protected] • www.vistapro.com
IMPORTANT SAFETY INSTRUCTIONS
THE LIGHTED LAMP IS HOT!!
WARNING: TO REDUCE THE RISK OF FIRE, OR INJURY TO
PERSONS:
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamps get hot quickly! Contact only switch/plug when turning on.
3. Do not touch hot lens, guard or enclosure.
4. Keep lamp away from material that may burn.
5. Do not touch the lamp at any time. Use a soft cloth. Oil from the skin may
damage lamp.
6. Do not operate luminaire tting with a missing or damaged cover.
SAVE THESE INSTRUCTIONS
LAMP INSTALLATION/REPLACEMENT:
CAUTION: Do not exceed maximum wattage marked
on luminaire label.
1. To prevent electrical shock, disconnect transformer
from electrical supply before service.
2. Remove shroud to expose lamp.
3. Replace lamp with correct wattage and type
marked on fixture label.
NOTE: DO NOT touch lamp with bare hands. Always
use soft cloth or the plastic wrapping (if available)
from lamp to handle the lamp.
4. Re-install shroud.
INSTALLATION INSTRUCTIONS
5237 (8/08)