vita VA20234 User manual

1. Corner Post (1) 3”x 3” x 43” - (8 cm x 8 cm x 109 cm) - White 10785, Brown 14094
2. Top Rails (2) 1 1/2” x 1 1/2” x 44.73” - (4 cm x 4 cm x 114 cm) - White 10787, Brown 14095
3. End Post (2) 3”x 3” x 38” - (8 cm x 8 cm x 97 cm) - White 10786, Brown 14096
4. 18”Pickets (6) 7/8”x 3” x 18” - (2 cm x 8 cm x 46 cm) - White 10132, Brown 14097
5. 19”Pickets (2) 7/8”x 3” x 19” - (2 cm x 8 cm x 48 cm) - White 10133, Brown 14098
6. Bottom Rails (2) 1 1/2” x 1 1/2” x 44.73” (8 cm x 8 cm x 114 cm) - White 10788, Brown 14099
7. 20 1/2”Pickets (2) 7/8” x 3” x 20 1/2” - (2 cm x 8 cm x 52 cm) -White 10134, Brown 14100
8. 23”Pickets (2) 7/8” x 3” x 23” - (2 cm x 8 cm x 58 cm) - White 10135, Brown 14101
Optional Materials
3 Bags of pre-mix concrete for extra post stability.
Tools You Will Need
•Shovel
•Tape measure
General Information
Read Instructions through carefully before
beginningassembly.
•When assembling components, place on a non-abrasive surface
(i.e. shipping box) to avoid scratching.
•We recommend an area approx 10 ft. x 8 ft. (3 m x 2.4 m) for unobstructed assembling.
•You should not need to use excessive force when assembling components.
Please read through beforestarting assembly.
IMPORTANT: CHECK THE INSIDE OF YOUR POSTS FOR ALL MATERIALS.
Check Box for These Contents
In the event of damaged, missing or defective parts please call our customer service dept. at 1 800 282 9346 (Mon.to Fri.8:00 AM to 5:00 PM EST).
ASSEMBLY INSTRUCTIONS
Country Corner Picket
White Vinyl - VA20234
Brown Composite Vinyl -VA84050
1
43.7 in
110.9 cm
Ver 2.4/081020
7
5
4
3
1
2
8
6
38.7 in
98.2 cm
42.5 in
108.0 cm
48.9 in
124.1 cm
www.wearevita.com

2
Layout the corner post.
Insert the top rail (holes on both sides of rail) into the top hole on
corner post ensuring that the holes in the rail are facing the other
hole in the corner post. This is critical to ensure proper orientation
for ultimately inserting pickets.
Insert the bottom rail (holes on one side) into the bottom hole
on corner post. Ensure that holes in the rail are facing the other
hole in the corner post.
Repeat steps 1 and 2 for the remaining top and bottom rails as
illustrated in the remaining two holes on the other side of the
corner post.
Insert the remaining open railends into the two end posts andpush
past the locking tabs to create the“frame” of your corner picket.
Starting with the 23”(58 cm) pickets, slip each
one down
through the top rail and into the bottom rail on either side of
the corner post. Note: The tabs on the end of the pickets go
into the bottom rail.
As in step 6,slip each of the remaining picketsthrough the next
five holes on either side of the corner post. Insert the pickets in
descending order, ending with three 18” (46 cm) pickets on each
side.
Country Corner Picket
Assemble the Post and Frame
2
3
1
13
4
4
5
6
7
86
7 8
42.5 in
108.0 cm
48.9 in
124.1 cm
5
12 in
30.5 cm
Level
Determine the desiredlocation for your corner picket, and dig
three 12”(30 cm) deep holes using the distances as illustrated.
Set the completed “frame” into the holes and check each rail
for level. At this time, you may need to adjust the depths of
the holes. Use a level to check each post and once youare
satisfied with the orientation,fill in the holes (cement is optional,
but recommended).
Assemble the Pickets
Once rails are inserted into holes and pushed past locking
tabs they will LOCKINTO PLACE PERMANENTLY.
2
Holes on
Both Sides
of Top Rail
Locking
Tab
*
*
Once pickets are inserted into holes and pushed past
locking tabs they will LOCKINTO PLACE PERMANENTLY.
*
*
www.wearevita.com