vita Sturbridge User manual

Check Boxes for These Contents (1 Box)
In the event of missing or defective parts please call our customer service dept. at 1 800 282 9346 (Mon. to Fri. 8:00 AM to 5:00 PM EST).
1. Lamp Post Top - (1) - 5” x 5“x 58” (12.7 x 12.7 x 147.3 cm) - 10890 White , 14053 Brown
2. Post Coupler (1) - 10725-1 White, 14052 Brown
3. Lamp Post Bottom - (1) - 5” x 5“x 14” (12.7 x 12.7 x 35.5 cm) - 10889 White, 14054 Brown
4. Post Cap (1) - 10789 White, 14051 Brown
5. Decorative Base Molding Trim Cap(1) - 10764 White, 14055 Brown
6. Decorative Base Molding - (1) - 10174-1 White, 14058 Brown (6"x6"x24" -
15.24 x 15.24 x 60.96 cm)
7. Decorative Base Molding Insert (1) - 10765 White, 14057 Brown
8. 1-1/2” Self -Tapping Screws (4) - 20005 White, 20031 Brown
9. Vinyl Weld Glue (1) - 20000 White, 20038 Brown
10. Post Trim (1) - 10698-1 White, 14029 Brown
Tools You Will Need
11. Wheelbarrow or bucket (to mix concrete)
12. Tape Measure
13. Level
14. Shovel
15. Drill
Purchased Separately
•Lamp.
•4x4 Pressure treated lumber. - 8’(2.4 m) long
•Two bags of pre-mix concrete. *
* Strongly recommended for the stability of this product.
General Information
•Read Instructions through carefully before beginning assembly.
•When handling components, place on a non-abrasive surface
(i.e.shipping box) to avoid scratching.
•We recommend an area approx 10’x 8’(3m x 2.4m) forunobstructedhandling.
Important Note:
•Please refer to local codes before installing outdoor lighting. UF-rated cable should be used for
underground wiring and all materials should be approved by the Underwriter’s Laborator (UL). Vita
assumes no liability for errors, omissions or the outcome of any project.
Please read through before starting assembly.
ASSEMBLY INSTRUCTIONS
The Sturbridge/Burton Lamp Post
1
1
Ver 5.6/080223
8
Not to Scale
    
    

  
  
  
  
4
9
Sturbridge/Burton Lamp Post
10
6
7
3
2
5
(7.62 cm)
(61 cm)
(13 cm)
(15 cm)
(183 cm)
(188 cm)
www.wearevita.com
(157cm)
57 in.

2
4
2
•Start by applying a small amount of glue to the underside of your Base
Molding Trim Cap (part #5) and to the top side of the Decorative Base
Molding Insert (part #7) as shown
•Attach to each end of the Decorative Base Molding (part #6) as shown
STEP THREE
Combine the Post, Decorative Base Molding and Trim
•Slide your completed Decorative Base Molding that you assembled in
Step One over the completed Lamp Post from Step Two. Slide the
Post Trim (part #10) onto the completed lamp post and measure
approximately 12" from top
•Temporarily slide the post trim up and out of the way and apply a thin
line of glue directly to the lamp post where you would like the trim
piece to sit. Carefully move the trim back into place over the glue and
hold for approximately 60 seconds or until trim stays in place (glue
will cure completely in 24 hours). Be sure to wipe away any excess
glue from your lamp post with a slightly damp cloth.
STEP TWO
Main Lamp Post Assembly
•Apply a small amount of glue to all four sides of your post coupler along
the ribbed surfaces on each end (part #2).
•Use the post coupler (part #2) to join the lamp post top (part #1) to the
lamp post bottom (part #3) as shown
STEP ONE
Decorative Base Molding Assembly
1
12"
(30.5 cm)
STEP FOUR
•Apply a thin line of glue inside the bottom of the post cap (part 4)
and attach to the top of your completed lamp post (image 3).
Wipe away excess glue and allow to cure for at least 60 seconds.
3

3
Lamp Post Installation
STEP FIVE
Lamp Post Installation
C
STEP SEVEN
SEVEN
Installing Lamp
OPTIONAL
•If necessary,pre-wire the lamp by running the wire inside the
cavity of the post through the universal 3 in. (7.62 cm) collar
(Image A). If installing a solar lamp, disregard this step.
•Slide the lamp post assembly over the wood post (Image B).
•Line up one corner of the vinyl post until it sits flush with the
corner of the wood post and fasten this corner at the top and
bottom of the post with the provided screws as shown (Image C).
Follow the instructions included with the lamp (purchased
separately) and secure it to the round collar on top of the post.You may
need to modify how it attaches to the collar.
B
A
Wood
Post
Top View
C
Ensure the lamp post wiring
is inside this cavity.
North America Toll Free Phone: [phone]
www.wearevita.com
•Dig a 36" (91.5cm) deep hole in the desired location. Verify the
depth of the hole to ensure that the 4x4 wood post will be buried
36" into the ground. Fill the hole 3/4 full with prepared pre-mix
concrete (not included). Insert the post into the concrete and
check for level. Allow time for the concrete to set, then fill in the
remainder of the hole.
Wood Post Installation
STEP SIX
5
36”
(91.4 cm)
Level
66““
(15.25 cm)
6
A