Vital Baby 443853 User manual

www.vitalbaby.com
Made in China to Vital Baby®specifications.
Vital Innovations Limited, Hatfield, Herts, AL10 9EW, United Kingdom.
Vital Baby®is a registered trademark. NURTURE™ is a trademark.
Patent protected. Design Rights. © Vital Innovations Ltd 2020.
pro UV steriliser & dryer
™
STERILISE MODE
1. Clean all parts according to the instructions given in “cleaning and
maintenance”. Ensure that all items to be sterilised have been thoroughly
cleaned and completely dried before putting into the machine for
sterilising without performing a dry cycle.
2. Open the lid and place your items into the steriliser. See diagrams 1 and 2
for placement guidance.
3. Close the lid and switch your steriliser on at the mains. The steriliser will
beep when on.
4. Press sterilise to select the function. There is 1 sterilising option of 11 minutes,
which will be automatically selected and displayed on the timer when
pressing sterilise . The time will flash when you press sterilise - once it has stopped
flashing and your sterilising cycle will begin.
If the lid is lifted during a cycle, the function will end. Do not open the lid
during a sterilising function, as this will affect the sterilisation results of
the contents.
To cancel your cycle at any point, press sterilise .
When your steriliser beeps 6 times your cycle is complete and your items
are fully sterilised. The steriliser will then enter standby mode and the
screen will switch off until the lid is opened.
DRY MODE
1. Clean all parts according to the instructions given in “cleaning and
maintenance”. Ensure that all items to be dried have been thoroughly
cleaned and roughly dried to remove excess water.
2. Open the lid and place your items into the steriliser. See diagrams 1 and 2
for placement guidance.
3. Press dry to select the function. There are 3 different cycles available -
31minutes (default), 41minutes and 51 minutes - for use depending on how
many items you have placed in the unit and how long it will take to dry
them. Ifthere are a lot of items in the steriliser, we recommend you choose
a longer cycle in order to ensure that all of your items are completely dry.
The time will flash until you have selected your cycle - once the time has
stopped flashing your drying cycle will begin.
4. If the lid is lifted during a cycle the function will end.
To cancel your cycle at any point press dry . If the fan is on when you press
the button, it will continue to dry for 15 seconds and enter standby mode
when finished.
When your steriliser beeps 6 times, your cycle is complete and your items
are dry. The steriliser will then enter standby mode and the screen will
switch off until the lid is opened.
STORE MODE
1. Clean all parts according to the instructions given in “cleaning &
maintenance”. Ensure that all items to be sterilised have been thoroughly
cleaned and roughly dried to remove excess water.
2. Open the lid and place your items into the steriliser.
3. Press to select the function. In store mode, the steriliser will initially
perform a full sterilising and drying cycle of 41 minutes. 41 minutes will be
automatically selected and displayed on the timer when pressing .
The time will flash when you press - once it has stopped flashing your
cycle will begin.
4. Once your steriliser has completed its auto cycle, store mode will then
commence. In store mode, once completing a full sterilising and drying
cycle, the steriliser will automatically sterilise the contents every 2 hours
for 2 minutes for up to 3 days or until the lid is opened.
If the lid is lifted during a cycle the function will end.
Tocancel your cycle at any point, press . If the fan is on when you
press the button, it will continue to dry for 15 seconds and enter standby
mode when finished.
When your steriliser beeps 6 times, your 72 hour cycle is complete. The
steriliser will then enter standby mode and the screen will switch off until
the lid is opened. To perform another ‘store’ cycle, repeat this section from
step 1.
TECHNICAL SPECIFICATION
Model: 443853
Drying Power: 240V~50Hz 75W
Inner Capacity: 7L
UV-LED light: 7V 3W
Wavelength: 275nm
DISPOSAL
In order to minimise hazards to health and the environment and ensure that
materials can be recycled, this product should be disposed of at a separate
collection facility for waste electrical and electronic equipment.
filter
REPLACING THE FILTER
• The filter in your UV steriliser
should be replaced every 6-12
months. Tochange the filter,
remove the filter casing using
the latch and gently pull the
filter out.
• Place the new filter over the vent
on the back of your steriliser
and replace the filter casing,
ensuring that the latch clicks
back into place.
• Place bottles (with the neck facing upwards), collars and caps upright in
the base of the steriliser and teats upright in the basket. We recommend
that no items come into contact with each other when placed in the
steriliser for accurate and efficient sterilising.
THIS WAY UP
Diagram 1 Diagram 2
Don’t forget to register your warranty at
www.vitalbaby.com/warranty
VB UVSteriliser A6 8pp Leaflet.indd 1-4VB UVSteriliser A6 8pp Leaflet.indd 1-4 13/02/2020 15:4513/02/2020 15:45

WARNING! INSTRUCTIONS FOR USE AND CARE.
IMPORTANT, READ CAREFULLY AND RETAIN FOR FUTURE USE.
• This appliance should not be used by children under the age of 16
or persons with reduced mental capabilities, or without the required
knowledge or experience. The product can be used by persons with
reduced physical or sensory capabilities as long as they are under
supervision or after they have received instructions for the safe use of the
appliance, and have understood the hazards involved. If the appliance is
sold by the purchaser or given to third party users, they must receive the
instructions for the safe use of the appliance. It is important to understand
the hazards involved, through reading the user manual and in particular the
safety warnings contained in it.
• The cleaning and maintenance to be performed by the user should not be
carried out by children under the age of 16 and / or people with reduced
mental capabilities or missing experience or required knowledge.
• Use the UV steriliser only for its intended use as described in this manual.
• Keep all components out of the reach of children. THIS IS NOT A TOY.
• Do not tug on the power cable, the steriliser or any of its components to
unplug from the wall.
• For safety reasons the appliance must always be connected to an
electricity system which has efficient earthing connections.
• Never immerse or drop the steriliser or plug in water or any other liquids.
Keep the device dry - RISK OF ELECTRIC SHOCK.
• Do not attempt to disassemble the steriliser – RISK OF ELECTRIC SHOCK.
• Regular care and cleaning is essential to maintain peak working order of
your steriliser.
• The steriliser and component parts may become damaged or broken if
mishandled, dropped or knocked over.
• Do not make any adjustments to the original plug.
• Before using the steriliser always check that all components are not
damaged. If damage is found do NOT use the product.
• Do not attempt to dismantle or repair the steriliser yourself.
• Clean all of the components thoroughly before first use and after each use.
• Never operate an electrical device if it has a damaged cord or plug, if it is
not working properly, if it has been dropped or damaged, or dropped into
water.
• Do not expose the steriliser to direct sunlight.
• Do not cover the air intake.
• Unwind the cord completely before inserting the plug into the socket; this
is to prevent possible overheating of the appliance.
• Do not place the appliance on or near hot surfaces or appliances such as
microwaves or ovens.
• This appliance does not contain parts or components serviceable by the
user.
• Do not reach for any electrical device that has fallen into water. Unplug
immediately from the mains.
• Take appropriate care in handling bottles and components.
• Do not store or leave in direct sunlight, near a source of heat or near a
source of water as this could damage the product.
• Do not pour water directly into the product.
• Place the appliance on flat and stable surfaces only.
CLEANING AND MAINTENANCE
• Before first use and after each use, clean all components thoroughly with
hot, soapy water. Wring excess water from the cloth or sponge before wiping
the appliance. After cleaning and before using for the first time, run a full 61
minute auto cycle followed by an 11 minute sterilisation cycle.
• Do not use bleach, abrasive materials, abrasive solutions or scourers to
clean the product. Never pour bleach or sterilising solutions/tablets into
the appliance.
• Before each use ensure that all items to be sterilised have been thoroughly
cleaned and roughly dried to remove excess water.
• Ensure that electrical items are not cleaned before sterilising. DO NOT GET
ELECTRICAL ITEMS WET.
INSTRUCTIONS FOR USE
Plug your new UV steriliser into the mains. When switched on it will beep, and
then enter standby mode until you are ready to use it. Once your items are in
the steriliser, press your desired function button to ‘wake it up’.
Place bottles and teats upright in the unit to optimise sterilising and drying
efficiency. See diagrams 1 and 2. Clean all parts according to the instructions
given in “cleaning and maintenance”. Ensure that all items to be sterilised
have been thoroughly cleaned and roughly dried to remove excess water.
Ifyou are using sterilise mode only without a drying cycle, ensure all items
are thoroughly dried before placing them in the steriliser. Ensure the contents
are disassembled and evenly spaced out to enable the UV light to reach all
areas. Do not wash items that are unsuitable for cleaning with water or fluids.
AUTO MODE
Clean all parts according to the instructions given in “cleaning and
maintenance”. Ensure that all items to be sterilised have been thoroughly
cleaned and roughly dried to remove excess water.
1. Open the lid and place your items into the steriliser. See diagrams 1 and 2
for placement guidance.
2. Close the lid and switch your steriliser on at the mains. The steriliser will
beep when on.
3. Press auto to select the function. There are 3 different cycles available -
41minutes (default), 51minutes and 61 minutes - for use depending on how
many items you have placed in the unit and how long it will take to dry
them. If there are a lot of items in the steriliser, we recommend you choose
a longer cycle in order to ensure that all of your items are completely dry
before the sterilising function begins. The time will flash until you have
stopped pressing auto , at which point the time will stop flashing and your
drying cycle will begin.
To cancel your cycle at any point, press auto . If the fan is on when you
press the button, it will continue to dry for 15 seconds and enter standby
mode when finished.
4. When the countdown timer displays 11 minutes, the sterilising cycle will
commence. As the steriliser uses UV light to sterilise, the appliance will
make no noise during this part of the cycle.
When your steriliser beeps 6 times, your cycle is complete and your items
are fully sterilised. After 1 minute, the machine will enter standby mode
and the screen will switch off until the lid is opened.
COMPONENTS CHECKLIST
STERILISE MODE
Sterilise mode can be
selected straight after
drying mode, or you
can go straight in to
an 11 minute sterilising
cycle if your items
are already clean
and dry. If you want
to end your function
mid-cycle, press sterilise or
open the lid to end the
function.
AUTO MODE
Auto mode starts by
drying the contents before
automatically moving on to
sterilising mode, doing all the
work for you. If you want to
end your function mid-cycle,
press auto or open the lid to
end the function.
TIMER
The timer
will count
down in
minutes and
show you
how much
time is left
on your
drying and/
or sterilising
cycle.
STORE MODE
In store mode the
steriliser dries and
sterilises multiple items,
before periodically
activating the bacteria
killing UV LED’s for 2
minutes every 2 hours for
up to 3 days (72 hours).
If you want to end your
function mid-cycle, press
or open the lid to end
the function.
DRY MODE
Dry your bottles, teats
and accessories after
cleaning them and
before sterilising to
ensure precise and
efficient sterilising.
If you want to end your
function mid-cycle,
press dry or open the lid
to end the function.
sterilising unit
teat and accessories basket
150ml and 240ml NURTURETM
breast like feeding bottles
and slow flow teats are
also included with your UV
steriliser
• Keep the appliance well away from other objects when in use. Do not place
items on top of the appliance.
• To immediately stop the appliance mid cycle, turn off at the mains socket
and disconnect the power cable.
VB UVSteriliser A6 8pp Leaflet.indd 5-8VB UVSteriliser A6 8pp Leaflet.indd 5-8 13/02/2020 15:4513/02/2020 15:45

WARNING! INSTRUCTIONS FOR USE AND CARE.
IMPORTANT, READ CAREFULLY AND RETAIN FOR FUTURE USE.
• This appliance should not be used by children under the age of 16
or persons with reduced mental capabilities, or without the required
knowledge or experience. The product can be used by persons with
reduced physical or sensory capabilities as long as they are under
supervision or after they have received instructions for the safe use of the
appliance, and have understood the hazards involved. If the appliance is
sold by the purchaser or given to third party users, they must receive the
instructions for the safe use of the appliance. It is important to understand
the hazards involved, through reading the user manual and in particular the
safety warnings contained in it.
• The cleaning and maintenance to be performed by the user should not be
carried out by children under the age of 16 and / or people with reduced
mental capabilities or missing experience or required knowledge.
• Use the UV steriliser only for its intended use as described in this manual.
• Keep all components out of the reach of children. THIS IS NOT A TOY.
• Do not tug on the power cable, the steriliser or any of its components to
unplug from the wall.
• For safety reasons the appliance must always be connected to an
electricity system which has efficient earthing connections.
• Never immerse or drop the steriliser or plug in water or any other liquids.
Keep the device dry - RISK OF ELECTRIC SHOCK.
• Do not attempt to disassemble the steriliser – RISK OF ELECTRIC SHOCK.
• Regular care and cleaning is essential to maintain peak working order of
your steriliser.
• The steriliser and component parts may become damaged or broken if
mishandled, dropped or knocked over.
• Do not make any adjustments to the original plug.
• Before using the steriliser always check that all components are not
damaged. If damage is found do NOT use the product.
• Do not attempt to dismantle or repair the steriliser yourself.
• Clean all of the components thoroughly before first use and after each use.
• Never operate an electrical device if it has a damaged cord or plug, if it is
not working properly, if it has been dropped or damaged, or dropped into
water.
• Do not expose the steriliser to direct sunlight.
• Do not cover the air intake.
• Unwind the cord completely before inserting the plug into the socket; this
is to prevent possible overheating of the appliance.
• Do not place the appliance on or near hot surfaces or appliances such as
microwaves or ovens.
• This appliance does not contain parts or components serviceable by the
user.
• Do not reach for any electrical device that has fallen into water. Unplug
immediately from the mains.
• Take appropriate care in handling bottles and components.
• Do not store or leave in direct sunlight, near a source of heat or near a
source of water as this could damage the product.
• Do not pour water directly into the product.
• Place the appliance on flat and stable surfaces only.
CLEANING AND MAINTENANCE
• Before first use and after each use, clean all components thoroughly with
hot, soapy water. Wring excess water from the cloth or sponge before wiping
the appliance. After cleaning and before using for the first time, run a full 61
minute auto cycle followed by an 11 minute sterilisation cycle.
• Do not use bleach, abrasive materials, abrasive solutions or scourers to
clean the product. Never pour bleach or sterilising solutions/tablets into
the appliance.
• Before each use ensure that all items to be sterilised have been thoroughly
cleaned and roughly dried to remove excess water.
• Ensure that electrical items are not cleaned before sterilising. DO NOT GET
ELECTRICAL ITEMS WET.
INSTRUCTIONS FOR USE
Plug your new UV steriliser into the mains. When switched on it will beep, and
then enter standby mode until you are ready to use it. Once your items are in
the steriliser, press your desired function button to ‘wake it up’.
Place bottles and teats upright in the unit to optimise sterilising and drying
efficiency. See diagrams 1 and 2. Clean all parts according to the instructions
given in “cleaning and maintenance”. Ensure that all items to be sterilised
have been thoroughly cleaned and roughly dried to remove excess water.
Ifyou are using sterilise mode only without a drying cycle, ensure all items
are thoroughly dried before placing them in the steriliser. Ensure the contents
are disassembled and evenly spaced out to enable the UV light to reach all
areas. Do not wash items that are unsuitable for cleaning with water or fluids.
AUTO MODE
Clean all parts according to the instructions given in “cleaning and
maintenance”. Ensure that all items to be sterilised have been thoroughly
cleaned and roughly dried to remove excess water.
1. Open the lid and place your items into the steriliser. See diagrams 1 and 2
for placement guidance.
2. Close the lid and switch your steriliser on at the mains. The steriliser will
beep when on.
3. Press auto to select the function. There are 3 different cycles available -
41minutes (default), 51minutes and 61 minutes - for use depending on how
many items you have placed in the unit and how long it will take to dry
them. If there are a lot of items in the steriliser, we recommend you choose
a longer cycle in order to ensure that all of your items are completely dry
before the sterilising function begins. The time will flash until you have
stopped pressing auto , at which point the time will stop flashing and your
drying cycle will begin.
To cancel your cycle at any point, press auto . If the fan is on when you
press the button, it will continue to dry for 15 seconds and enter standby
mode when finished.
4. When the countdown timer displays 11 minutes, the sterilising cycle will
commence. As the steriliser uses UV light to sterilise, the appliance will
make no noise during this part of the cycle.
When your steriliser beeps 6 times, your cycle is complete and your items
are fully sterilised. After 1 minute, the machine will enter standby mode
and the screen will switch off until the lid is opened.
COMPONENTS CHECKLIST
STERILISE MODE
Sterilise mode can be
selected straight after
drying mode, or you
can go straight in to
an 11 minute sterilising
cycle if your items
are already clean
and dry. If you want
to end your function
mid-cycle, press sterilise or
open the lid to end the
function.
AUTO MODE
Auto mode starts by
drying the contents before
automatically moving on to
sterilising mode, doing all the
work for you. If you want to
end your function mid-cycle,
press auto or open the lid to
end the function.
TIMER
The timer
will count
down in
minutes and
show you
how much
time is left
on your
drying and/
or sterilising
cycle.
STORE MODE
In store mode the
steriliser dries and
sterilises multiple items,
before periodically
activating the bacteria
killing UV LED’s for 2
minutes every 2 hours for
up to 3 days (72 hours).
If you want to end your
function mid-cycle, press
or open the lid to end
the function.
DRY MODE
Dry your bottles, teats
and accessories after
cleaning them and
before sterilising to
ensure precise and
efficient sterilising.
If you want to end your
function mid-cycle,
press dry or open the lid
to end the function.
sterilising unit
teat and accessories basket
150ml and 240ml NURTURETM
breast like feeding bottles
and slow flow teats are
also included with your UV
steriliser
• Keep the appliance well away from other objects when in use. Do not place
items on top of the appliance.
• To immediately stop the appliance mid cycle, turn off at the mains socket
and disconnect the power cable.
VB UVSteriliser A6 8pp Leaflet.indd 5-8VB UVSteriliser A6 8pp Leaflet.indd 5-8 13/02/2020 15:4513/02/2020 15:45

WARNING! INSTRUCTIONS FOR USE AND CARE.
IMPORTANT, READ CAREFULLY AND RETAIN FOR FUTURE USE.
• This appliance should not be used by children under the age of 16
or persons with reduced mental capabilities, or without the required
knowledge or experience. The product can be used by persons with
reduced physical or sensory capabilities as long as they are under
supervision or after they have received instructions for the safe use of the
appliance, and have understood the hazards involved. If the appliance is
sold by the purchaser or given to third party users, they must receive the
instructions for the safe use of the appliance. It is important to understand
the hazards involved, through reading the user manual and in particular the
safety warnings contained in it.
• The cleaning and maintenance to be performed by the user should not be
carried out by children under the age of 16 and / or people with reduced
mental capabilities or missing experience or required knowledge.
• Use the UV steriliser only for its intended use as described in this manual.
• Keep all components out of the reach of children. THIS IS NOT A TOY.
• Do not tug on the power cable, the steriliser or any of its components to
unplug from the wall.
• For safety reasons the appliance must always be connected to an
electricity system which has efficient earthing connections.
• Never immerse or drop the steriliser or plug in water or any other liquids.
Keep the device dry - RISK OF ELECTRIC SHOCK.
• Do not attempt to disassemble the steriliser – RISK OF ELECTRIC SHOCK.
• Regular care and cleaning is essential to maintain peak working order of
your steriliser.
• The steriliser and component parts may become damaged or broken if
mishandled, dropped or knocked over.
• Do not make any adjustments to the original plug.
• Before using the steriliser always check that all components are not
damaged. If damage is found do NOT use the product.
• Do not attempt to dismantle or repair the steriliser yourself.
• Clean all of the components thoroughly before first use and after each use.
• Never operate an electrical device if it has a damaged cord or plug, if it is
not working properly, if it has been dropped or damaged, or dropped into
water.
• Do not expose the steriliser to direct sunlight.
• Do not cover the air intake.
• Unwind the cord completely before inserting the plug into the socket; this
is to prevent possible overheating of the appliance.
• Do not place the appliance on or near hot surfaces or appliances such as
microwaves or ovens.
• This appliance does not contain parts or components serviceable by the
user.
• Do not reach for any electrical device that has fallen into water. Unplug
immediately from the mains.
• Take appropriate care in handling bottles and components.
• Do not store or leave in direct sunlight, near a source of heat or near a
source of water as this could damage the product.
• Do not pour water directly into the product.
• Place the appliance on flat and stable surfaces only.
CLEANING AND MAINTENANCE
• Before first use and after each use, clean all components thoroughly with
hot, soapy water. Wring excess water from the cloth or sponge before wiping
the appliance. After cleaning and before using for the first time, run a full 61
minute auto cycle followed by an 11 minute sterilisation cycle.
• Do not use bleach, abrasive materials, abrasive solutions or scourers to
clean the product. Never pour bleach or sterilising solutions/tablets into
the appliance.
• Before each use ensure that all items to be sterilised have been thoroughly
cleaned and roughly dried to remove excess water.
• Ensure that electrical items are not cleaned before sterilising. DO NOT GET
ELECTRICAL ITEMS WET.
INSTRUCTIONS FOR USE
Plug your new UV steriliser into the mains. When switched on it will beep, and
then enter standby mode until you are ready to use it. Once your items are in
the steriliser, press your desired function button to ‘wake it up’.
Place bottles and teats upright in the unit to optimise sterilising and drying
efficiency. See diagrams 1 and 2. Clean all parts according to the instructions
given in “cleaning and maintenance”. Ensure that all items to be sterilised
have been thoroughly cleaned and roughly dried to remove excess water.
Ifyou are using sterilise mode only without a drying cycle, ensure all items
are thoroughly dried before placing them in the steriliser. Ensure the contents
are disassembled and evenly spaced out to enable the UV light to reach all
areas. Do not wash items that are unsuitable for cleaning with water or fluids.
AUTO MODE
Clean all parts according to the instructions given in “cleaning and
maintenance”. Ensure that all items to be sterilised have been thoroughly
cleaned and roughly dried to remove excess water.
1. Open the lid and place your items into the steriliser. See diagrams 1 and 2
for placement guidance.
2. Close the lid and switch your steriliser on at the mains. The steriliser will
beep when on.
3. Press auto to select the function. There are 3 different cycles available -
41minutes (default), 51minutes and 61 minutes - for use depending on how
many items you have placed in the unit and how long it will take to dry
them. If there are a lot of items in the steriliser, we recommend you choose
a longer cycle in order to ensure that all of your items are completely dry
before the sterilising function begins. The time will flash until you have
stopped pressing auto , at which point the time will stop flashing and your
drying cycle will begin.
To cancel your cycle at any point, press auto . If the fan is on when you
press the button, it will continue to dry for 15 seconds and enter standby
mode when finished.
4. When the countdown timer displays 11 minutes, the sterilising cycle will
commence. As the steriliser uses UV light to sterilise, the appliance will
make no noise during this part of the cycle.
When your steriliser beeps 6 times, your cycle is complete and your items
are fully sterilised. After 1 minute, the machine will enter standby mode
and the screen will switch off until the lid is opened.
COMPONENTS CHECKLIST
STERILISE MODE
Sterilise mode can be
selected straight after
drying mode, or you
can go straight in to
an 11 minute sterilising
cycle if your items
are already clean
and dry. If you want
to end your function
mid-cycle, press sterilise or
open the lid to end the
function.
AUTO MODE
Auto mode starts by
drying the contents before
automatically moving on to
sterilising mode, doing all the
work for you. If you want to
end your function mid-cycle,
press auto or open the lid to
end the function.
TIMER
The timer
will count
down in
minutes and
show you
how much
time is left
on your
drying and/
or sterilising
cycle.
STORE MODE
In store mode the
steriliser dries and
sterilises multiple items,
before periodically
activating the bacteria
killing UV LED’s for 2
minutes every 2 hours for
up to 3 days (72 hours).
If you want to end your
function mid-cycle, press
or open the lid to end
the function.
DRY MODE
Dry your bottles, teats
and accessories after
cleaning them and
before sterilising to
ensure precise and
efficient sterilising.
If you want to end your
function mid-cycle,
press dry or open the lid
to end the function.
sterilising unit
teat and accessories basket
150ml and 240ml NURTURETM
breast like feeding bottles
and slow flow teats are
also included with your UV
steriliser
• Keep the appliance well away from other objects when in use. Do not place
items on top of the appliance.
• To immediately stop the appliance mid cycle, turn off at the mains socket
and disconnect the power cable.
VB UVSteriliser A6 8pp Leaflet.indd 5-8VB UVSteriliser A6 8pp Leaflet.indd 5-8 13/02/2020 15:4513/02/2020 15:45

WARNING! INSTRUCTIONS FOR USE AND CARE.
IMPORTANT, READ CAREFULLY AND RETAIN FOR FUTURE USE.
• This appliance should not be used by children under the age of 16
or persons with reduced mental capabilities, or without the required
knowledge or experience. The product can be used by persons with
reduced physical or sensory capabilities as long as they are under
supervision or after they have received instructions for the safe use of the
appliance, and have understood the hazards involved. If the appliance is
sold by the purchaser or given to third party users, they must receive the
instructions for the safe use of the appliance. It is important to understand
the hazards involved, through reading the user manual and in particular the
safety warnings contained in it.
• The cleaning and maintenance to be performed by the user should not be
carried out by children under the age of 16 and / or people with reduced
mental capabilities or missing experience or required knowledge.
• Use the UV steriliser only for its intended use as described in this manual.
• Keep all components out of the reach of children. THIS IS NOT A TOY.
• Do not tug on the power cable, the steriliser or any of its components to
unplug from the wall.
• For safety reasons the appliance must always be connected to an
electricity system which has efficient earthing connections.
• Never immerse or drop the steriliser or plug in water or any other liquids.
Keep the device dry - RISK OF ELECTRIC SHOCK.
• Do not attempt to disassemble the steriliser – RISK OF ELECTRIC SHOCK.
• Regular care and cleaning is essential to maintain peak working order of
your steriliser.
• The steriliser and component parts may become damaged or broken if
mishandled, dropped or knocked over.
• Do not make any adjustments to the original plug.
• Before using the steriliser always check that all components are not
damaged. If damage is found do NOT use the product.
• Do not attempt to dismantle or repair the steriliser yourself.
• Clean all of the components thoroughly before first use and after each use.
• Never operate an electrical device if it has a damaged cord or plug, if it is
not working properly, if it has been dropped or damaged, or dropped into
water.
• Do not expose the steriliser to direct sunlight.
• Do not cover the air intake.
• Unwind the cord completely before inserting the plug into the socket; this
is to prevent possible overheating of the appliance.
• Do not place the appliance on or near hot surfaces or appliances such as
microwaves or ovens.
• This appliance does not contain parts or components serviceable by the
user.
• Do not reach for any electrical device that has fallen into water. Unplug
immediately from the mains.
• Take appropriate care in handling bottles and components.
• Do not store or leave in direct sunlight, near a source of heat or near a
source of water as this could damage the product.
• Do not pour water directly into the product.
• Place the appliance on flat and stable surfaces only.
CLEANING AND MAINTENANCE
• Before first use and after each use, clean all components thoroughly with
hot, soapy water. Wring excess water from the cloth or sponge before wiping
the appliance. After cleaning and before using for the first time, run a full 61
minute auto cycle followed by an 11 minute sterilisation cycle.
• Do not use bleach, abrasive materials, abrasive solutions or scourers to
clean the product. Never pour bleach or sterilising solutions/tablets into
the appliance.
• Before each use ensure that all items to be sterilised have been thoroughly
cleaned and roughly dried to remove excess water.
• Ensure that electrical items are not cleaned before sterilising. DO NOT GET
ELECTRICAL ITEMS WET.
INSTRUCTIONS FOR USE
Plug your new UV steriliser into the mains. When switched on it will beep, and
then enter standby mode until you are ready to use it. Once your items are in
the steriliser, press your desired function button to ‘wake it up’.
Place bottles and teats upright in the unit to optimise sterilising and drying
efficiency. See diagrams 1 and 2. Clean all parts according to the instructions
given in “cleaning and maintenance”. Ensure that all items to be sterilised
have been thoroughly cleaned and roughly dried to remove excess water.
Ifyou are using sterilise mode only without a drying cycle, ensure all items
are thoroughly dried before placing them in the steriliser. Ensure the contents
are disassembled and evenly spaced out to enable the UV light to reach all
areas. Do not wash items that are unsuitable for cleaning with water or fluids.
AUTO MODE
Clean all parts according to the instructions given in “cleaning and
maintenance”. Ensure that all items to be sterilised have been thoroughly
cleaned and roughly dried to remove excess water.
1. Open the lid and place your items into the steriliser. See diagrams 1 and 2
for placement guidance.
2. Close the lid and switch your steriliser on at the mains. The steriliser will
beep when on.
3. Press auto to select the function. There are 3 different cycles available -
41minutes (default), 51minutes and 61 minutes - for use depending on how
many items you have placed in the unit and how long it will take to dry
them. If there are a lot of items in the steriliser, we recommend you choose
a longer cycle in order to ensure that all of your items are completely dry
before the sterilising function begins. The time will flash until you have
stopped pressing auto , at which point the time will stop flashing and your
drying cycle will begin.
To cancel your cycle at any point, press auto . If the fan is on when you
press the button, it will continue to dry for 15 seconds and enter standby
mode when finished.
4. When the countdown timer displays 11 minutes, the sterilising cycle will
commence. As the steriliser uses UV light to sterilise, the appliance will
make no noise during this part of the cycle.
When your steriliser beeps 6 times, your cycle is complete and your items
are fully sterilised. After 1 minute, the machine will enter standby mode
and the screen will switch off until the lid is opened.
COMPONENTS CHECKLIST
STERILISE MODE
Sterilise mode can be
selected straight after
drying mode, or you
can go straight in to
an 11 minute sterilising
cycle if your items
are already clean
and dry. If you want
to end your function
mid-cycle, press sterilise or
open the lid to end the
function.
AUTO MODE
Auto mode starts by
drying the contents before
automatically moving on to
sterilising mode, doing all the
work for you. If you want to
end your function mid-cycle,
press auto or open the lid to
end the function.
TIMER
The timer
will count
down in
minutes and
show you
how much
time is left
on your
drying and/
or sterilising
cycle.
STORE MODE
In store mode the
steriliser dries and
sterilises multiple items,
before periodically
activating the bacteria
killing UV LED’s for 2
minutes every 2 hours for
up to 3 days (72 hours).
If you want to end your
function mid-cycle, press
or open the lid to end
the function.
DRY MODE
Dry your bottles, teats
and accessories after
cleaning them and
before sterilising to
ensure precise and
efficient sterilising.
If you want to end your
function mid-cycle,
press dry or open the lid
to end the function.
sterilising unit
teat and accessories basket
150ml and 240ml NURTURETM
breast like feeding bottles
and slow flow teats are
also included with your UV
steriliser
• Keep the appliance well away from other objects when in use. Do not place
items on top of the appliance.
• To immediately stop the appliance mid cycle, turn off at the mains socket
and disconnect the power cable.
VB UVSteriliser A6 8pp Leaflet.indd 5-8VB UVSteriliser A6 8pp Leaflet.indd 5-8 13/02/2020 15:4513/02/2020 15:45

www.vitalbaby.com
Made in China to Vital Baby®specifications.
Vital Innovations Limited, Hatfield, Herts, AL10 9EW, United Kingdom.
Vital Baby®is a registered trademark. NURTURE™ is a trademark.
Patent protected. Design Rights. © Vital Innovations Ltd 2020.
pro UV steriliser & dryer
™
STERILISE MODE
1. Clean all parts according to the instructions given in “cleaning and
maintenance”. Ensure that all items to be sterilised have been thoroughly
cleaned and completely dried before putting into the machine for
sterilising without performing a dry cycle.
2. Open the lid and place your items into the steriliser. See diagrams 1 and 2
for placement guidance.
3. Close the lid and switch your steriliser on at the mains. The steriliser will
beep when on.
4. Press sterilise to select the function. There is 1 sterilising option of 11 minutes,
which will be automatically selected and displayed on the timer when
pressing sterilise . The time will flash when you press sterilise - once it has stopped
flashing and your sterilising cycle will begin.
If the lid is lifted during a cycle, the function will end. Do not open the lid
during a sterilising function, as this will affect the sterilisation results of
the contents.
To cancel your cycle at any point, press sterilise .
When your steriliser beeps 6 times your cycle is complete and your items
are fully sterilised. The steriliser will then enter standby mode and the
screen will switch off until the lid is opened.
DRY MODE
1. Clean all parts according to the instructions given in “cleaning and
maintenance”. Ensure that all items to be dried have been thoroughly
cleaned and roughly dried to remove excess water.
2. Open the lid and place your items into the steriliser. See diagrams 1 and 2
for placement guidance.
3. Press dry to select the function. There are 3 different cycles available -
31minutes (default), 41minutes and 51 minutes - for use depending on how
many items you have placed in the unit and how long it will take to dry
them. Ifthere are a lot of items in the steriliser, we recommend you choose
a longer cycle in order to ensure that all of your items are completely dry.
The time will flash until you have selected your cycle - once the time has
stopped flashing your drying cycle will begin.
4. If the lid is lifted during a cycle the function will end.
To cancel your cycle at any point press dry . If the fan is on when you press
the button, it will continue to dry for 15 seconds and enter standby mode
when finished.
When your steriliser beeps 6 times, your cycle is complete and your items
are dry. The steriliser will then enter standby mode and the screen will
switch off until the lid is opened.
STORE MODE
1. Clean all parts according to the instructions given in “cleaning &
maintenance”. Ensure that all items to be sterilised have been thoroughly
cleaned and roughly dried to remove excess water.
2. Open the lid and place your items into the steriliser.
3. Press to select the function. In store mode, the steriliser will initially
perform a full sterilising and drying cycle of 41 minutes. 41 minutes will be
automatically selected and displayed on the timer when pressing .
The time will flash when you press - once it has stopped flashing your
cycle will begin.
4. Once your steriliser has completed its auto cycle, store mode will then
commence. In store mode, once completing a full sterilising and drying
cycle, the steriliser will automatically sterilise the contents every 2 hours
for 2 minutes for up to 3 days or until the lid is opened.
If the lid is lifted during a cycle the function will end.
Tocancel your cycle at any point, press . If the fan is on when you
press the button, it will continue to dry for 15 seconds and enter standby
mode when finished.
When your steriliser beeps 6 times, your 72 hour cycle is complete. The
steriliser will then enter standby mode and the screen will switch off until
the lid is opened. To perform another ‘store’ cycle, repeat this section from
step 1.
TECHNICAL SPECIFICATION
Model: 443853
Drying Power: 240V~50Hz 75W
Inner Capacity: 7L
UV-LED light: 7V 3W
Wavelength: 275nm
DISPOSAL
In order to minimise hazards to health and the environment and ensure that
materials can be recycled, this product should be disposed of at a separate
collection facility for waste electrical and electronic equipment.
filter
REPLACING THE FILTER
• The filter in your UV steriliser
should be replaced every 6-12
months. Tochange the filter,
remove the filter casing using
the latch and gently pull the
filter out.
• Place the new filter over the vent
on the back of your steriliser
and replace the filter casing,
ensuring that the latch clicks
back into place.
• Place bottles (with the neck facing upwards), collars and caps upright in
the base of the steriliser and teats upright in the basket. We recommend
that no items come into contact with each other when placed in the
steriliser for accurate and efficient sterilising.
THIS WAY UP
Diagram 1 Diagram 2
Don’t forget to register your warranty at
www.vitalbaby.com/warranty
VB UVSteriliser A6 8pp Leaflet.indd 1-4VB UVSteriliser A6 8pp Leaflet.indd 1-4 13/02/2020 15:4513/02/2020 15:45

www.vitalbaby.com
Made in China to Vital Baby®specifications.
Vital Innovations Limited, Hatfield, Herts, AL10 9EW, United Kingdom.
Vital Baby®is a registered trademark. NURTURE™ is a trademark.
Patent protected. Design Rights. © Vital Innovations Ltd 2020.
pro UV steriliser & dryer
™
STERILISE MODE
1. Clean all parts according to the instructions given in “cleaning and
maintenance”. Ensure that all items to be sterilised have been thoroughly
cleaned and completely dried before putting into the machine for
sterilising without performing a dry cycle.
2. Open the lid and place your items into the steriliser. See diagrams 1 and 2
for placement guidance.
3. Close the lid and switch your steriliser on at the mains. The steriliser will
beep when on.
4. Press sterilise to select the function. There is 1 sterilising option of 11 minutes,
which will be automatically selected and displayed on the timer when
pressing sterilise . The time will flash when you press sterilise - once it has stopped
flashing and your sterilising cycle will begin.
If the lid is lifted during a cycle, the function will end. Do not open the lid
during a sterilising function, as this will affect the sterilisation results of
the contents.
To cancel your cycle at any point, press sterilise .
When your steriliser beeps 6 times your cycle is complete and your items
are fully sterilised. The steriliser will then enter standby mode and the
screen will switch off until the lid is opened.
DRY MODE
1. Clean all parts according to the instructions given in “cleaning and
maintenance”. Ensure that all items to be dried have been thoroughly
cleaned and roughly dried to remove excess water.
2. Open the lid and place your items into the steriliser. See diagrams 1 and 2
for placement guidance.
3. Press dry to select the function. There are 3 different cycles available -
31minutes (default), 41minutes and 51 minutes - for use depending on how
many items you have placed in the unit and how long it will take to dry
them. Ifthere are a lot of items in the steriliser, we recommend you choose
a longer cycle in order to ensure that all of your items are completely dry.
The time will flash until you have selected your cycle - once the time has
stopped flashing your drying cycle will begin.
4. If the lid is lifted during a cycle the function will end.
To cancel your cycle at any point press dry . If the fan is on when you press
the button, it will continue to dry for 15 seconds and enter standby mode
when finished.
When your steriliser beeps 6 times, your cycle is complete and your items
are dry. The steriliser will then enter standby mode and the screen will
switch off until the lid is opened.
STORE MODE
1. Clean all parts according to the instructions given in “cleaning &
maintenance”. Ensure that all items to be sterilised have been thoroughly
cleaned and roughly dried to remove excess water.
2. Open the lid and place your items into the steriliser.
3. Press to select the function. In store mode, the steriliser will initially
perform a full sterilising and drying cycle of 41 minutes. 41 minutes will be
automatically selected and displayed on the timer when pressing .
The time will flash when you press - once it has stopped flashing your
cycle will begin.
4. Once your steriliser has completed its auto cycle, store mode will then
commence. In store mode, once completing a full sterilising and drying
cycle, the steriliser will automatically sterilise the contents every 2 hours
for 2 minutes for up to 3 days or until the lid is opened.
If the lid is lifted during a cycle the function will end.
Tocancel your cycle at any point, press . If the fan is on when you
press the button, it will continue to dry for 15 seconds and enter standby
mode when finished.
When your steriliser beeps 6 times, your 72 hour cycle is complete. The
steriliser will then enter standby mode and the screen will switch off until
the lid is opened. To perform another ‘store’ cycle, repeat this section from
step 1.
TECHNICAL SPECIFICATION
Model: 443853
Drying Power: 240V~50Hz 75W
Inner Capacity: 7L
UV-LED light: 7V 3W
Wavelength: 275nm
DISPOSAL
In order to minimise hazards to health and the environment and ensure that
materials can be recycled, this product should be disposed of at a separate
collection facility for waste electrical and electronic equipment.
filter
REPLACING THE FILTER
• The filter in your UV steriliser
should be replaced every 6-12
months. Tochange the filter,
remove the filter casing using
the latch and gently pull the
filter out.
• Place the new filter over the vent
on the back of your steriliser
and replace the filter casing,
ensuring that the latch clicks
back into place.
• Place bottles (with the neck facing upwards), collars and caps upright in
the base of the steriliser and teats upright in the basket. We recommend
that no items come into contact with each other when placed in the
steriliser for accurate and efficient sterilising.
THIS WAY UP
Diagram 1 Diagram 2
Don’t forget to register your warranty at
www.vitalbaby.com/warranty
VB UVSteriliser A6 8pp Leaflet.indd 1-4VB UVSteriliser A6 8pp Leaflet.indd 1-4 13/02/2020 15:4513/02/2020 15:45

www.vitalbaby.com
Made in China to Vital Baby®specifications.
Vital Innovations Limited, Hatfield, Herts, AL10 9EW, United Kingdom.
Vital Baby®is a registered trademark. NURTURE™ is a trademark.
Patent protected. Design Rights. © Vital Innovations Ltd 2020.
pro UV steriliser & dryer
™
STERILISE MODE
1. Clean all parts according to the instructions given in “cleaning and
maintenance”. Ensure that all items to be sterilised have been thoroughly
cleaned and completely dried before putting into the machine for
sterilising without performing a dry cycle.
2. Open the lid and place your items into the steriliser. See diagrams 1 and 2
for placement guidance.
3. Close the lid and switch your steriliser on at the mains. The steriliser will
beep when on.
4. Press sterilise to select the function. There is 1 sterilising option of 11 minutes,
which will be automatically selected and displayed on the timer when
pressing sterilise . The time will flash when you press sterilise - once it has stopped
flashing and your sterilising cycle will begin.
If the lid is lifted during a cycle, the function will end. Do not open the lid
during a sterilising function, as this will affect the sterilisation results of
the contents.
To cancel your cycle at any point, press sterilise .
When your steriliser beeps 6 times your cycle is complete and your items
are fully sterilised. The steriliser will then enter standby mode and the
screen will switch off until the lid is opened.
DRY MODE
1. Clean all parts according to the instructions given in “cleaning and
maintenance”. Ensure that all items to be dried have been thoroughly
cleaned and roughly dried to remove excess water.
2. Open the lid and place your items into the steriliser. See diagrams 1 and 2
for placement guidance.
3. Press dry to select the function. There are 3 different cycles available -
31minutes (default), 41minutes and 51 minutes - for use depending on how
many items you have placed in the unit and how long it will take to dry
them. Ifthere are a lot of items in the steriliser, we recommend you choose
a longer cycle in order to ensure that all of your items are completely dry.
The time will flash until you have selected your cycle - once the time has
stopped flashing your drying cycle will begin.
4. If the lid is lifted during a cycle the function will end.
To cancel your cycle at any point press dry . If the fan is on when you press
the button, it will continue to dry for 15 seconds and enter standby mode
when finished.
When your steriliser beeps 6 times, your cycle is complete and your items
are dry. The steriliser will then enter standby mode and the screen will
switch off until the lid is opened.
STORE MODE
1. Clean all parts according to the instructions given in “cleaning &
maintenance”. Ensure that all items to be sterilised have been thoroughly
cleaned and roughly dried to remove excess water.
2. Open the lid and place your items into the steriliser.
3. Press to select the function. In store mode, the steriliser will initially
perform a full sterilising and drying cycle of 41 minutes. 41 minutes will be
automatically selected and displayed on the timer when pressing .
The time will flash when you press - once it has stopped flashing your
cycle will begin.
4. Once your steriliser has completed its auto cycle, store mode will then
commence. In store mode, once completing a full sterilising and drying
cycle, the steriliser will automatically sterilise the contents every 2 hours
for 2 minutes for up to 3 days or until the lid is opened.
If the lid is lifted during a cycle the function will end.
Tocancel your cycle at any point, press . If the fan is on when you
press the button, it will continue to dry for 15 seconds and enter standby
mode when finished.
When your steriliser beeps 6 times, your 72 hour cycle is complete. The
steriliser will then enter standby mode and the screen will switch off until
the lid is opened. To perform another ‘store’ cycle, repeat this section from
step 1.
TECHNICAL SPECIFICATION
Model: 443853
Drying Power: 240V~50Hz 75W
Inner Capacity: 7L
UV-LED light: 7V 3W
Wavelength: 275nm
DISPOSAL
In order to minimise hazards to health and the environment and ensure that
materials can be recycled, this product should be disposed of at a separate
collection facility for waste electrical and electronic equipment.
filter
REPLACING THE FILTER
• The filter in your UV steriliser
should be replaced every 6-12
months. Tochange the filter,
remove the filter casing using
the latch and gently pull the
filter out.
• Place the new filter over the vent
on the back of your steriliser
and replace the filter casing,
ensuring that the latch clicks
back into place.
• Place bottles (with the neck facing upwards), collars and caps upright in
the base of the steriliser and teats upright in the basket. We recommend
that no items come into contact with each other when placed in the
steriliser for accurate and efficient sterilising.
THIS WAY UP
Diagram 1 Diagram 2
Don’t forget to register your warranty at
www.vitalbaby.com/warranty
VB UVSteriliser A6 8pp Leaflet.indd 1-4VB UVSteriliser A6 8pp Leaflet.indd 1-4 13/02/2020 15:4513/02/2020 15:45