VITINNI SL-589SW User manual

LED DESK LAMP
PLEASE READ AND KEEP THESE INSTRUCTIONS FOR FUTURE USE
SAP Code: JO02020102
Model Number: SL-589SW
For further assistance, other products and more, join us at:
Website: www.vitinni.co.uk
Instagram: @vitinniuk
Facebook: www.facebook.com/vitinni

Thank you for choosing our Vitinni LED Desk Lamp. Please read this user
manual carefully and keep it for future reference. If you need any
assistance, please contact our customer service team on the details
provided on the back page of this manual.
Items Supplied
Please check the list of supplied items which correspond to the numbered
diagrams below:
Please ensure that you have received all of the above items and check
for any damages before use. If you find any damages, please contact
our customer services department.
Lamp Adaptor Instruction Manual
Please read the following instructions below carefully before using
the lamp.
Please do not cover the lamp with cloth or paper
Pleasedonotplaceanymetalorinflammableobjectswithinthelamp
parts
Please do not use the lamp where children can touch it
Please do not repair, reform or break down the lamp
Please do not use the lamp when wires are damaged (wires outside
or disconnected)
Pleasedonotprocess,twist,damagethewireormakeitblockedby
heavyobjects
Please do not use the lamp in unstable circumstances or close to
flammable materials to avoid fire or injury
Pleasedonotusethelampinbathroomorotherplaceswithexcessive
moisture
Please do not use the lamp where the voltage isunstable
Please do not look at the LED directly in case of eye damage
1

Item
Specification
Light Source
LED
Rated Input
DC12V
Lamp Power
8W I- 1W
Wireless Charging Power
Max 10W
Lamp Material
ABS+6063AL
Dimensions
45*15*6.6cm
Lamp Net Weight
Around 1 kg
Function
Wireless Charging
2
Specifications
Instructions for Use
Note:
The turning/rotating of the lamp should only be undertaken within the marked angle
as shown in the picture.
When the rotation angle reaches the limit, please do not turn/rotate the joint with
additional force to avoid breaking the lamp.
The lamp should be placed on an even and balanced surface to ensure stability.

Aluminium alloy
3
Aluminium alloy
Surface light guide plate
Reinforced shaft
DC port
Wireless charging
Touch sensor control
Product Components
Light adjustment instructions
Use the 7 points along the touch sensor at the bottom of the unit to adjust the
brightness of the desk light as shown in the below picture:
Wireless charging
indicator
Key:
Green Light = Wireless charging is working
Yellow Light = When fully charged
Red Light = Charging fault

4
Safety Instructions
Only use the Desk Lamp with the supplied mains adaptor
This appliance is for indoor use only
The LEDs fitted in this desk lamp are not replaceable. When the
LEDs reach the end of their service life the whole lamp should be
replaced.
Caution: Misuse of the desk lamp could cause injury –do not use
the appliance for anything other than its intended use
For indoor use only
Cleaning & Maintenance
Clean the product on a regular basis with a soft and clean cloth to
remove any dust particles
Do not use volatile, highly corrosive liquids (such as gas or
thinners) to wipe the lamp in order to prevent damage or
discoloration
Please be sure to turn off the power before cleaning the products
If a failure in the lamp occurs, turn off the power and contact the
manufacturer

Guarantee
Our products are guaranteed for a period of 2 years from the date of purchase.
Products that develop a fault within this period are covered by our warranty and
we will replace defective parts, or where not available the whole product. The
warranty does not apply to any defect in the goods arising from fair wear and
tear, wilful damage, accident, negligence by you or any third party, use otherwise
than as recommended by us, failure to follow our instructions, any alteration or
repair carried out without our approval or has been the subject of commercial
use. Your statutory rights remain unaffected, in particular any rights you have
under the Consumer Rights Act 2015.
If you have a problem with your product within this warranty period please contact
our customer services team.
In the event of changes to the specification of a product and we are not able to
replace parts, we will replace the whole product within the 2 year guarantee
period
For products that fall outside of the 2 year guarantee, we will endeavour to
provide spare parts to purchase for as many of the replaceable parts as possible,
but cannot foresee specification changes or upgrades to products or parts outside
of the initial 2 year period.
If you would like further advice or information on your product, ensure you have the
SAP code ready and please get in touch with us at Vitinni on the contact options
below:
Phone: [phone] (Mon –Fri 9am to 5pm)
Email: [e-mail]
Address: Vitinni, Vale Mill (Rochdale) Ltd, Robinson Street, Rochdale, OL16 1TA
5

WEEE INFORMATION
The symbol on this product or its packaging means that this product and
its fan motors may not be treated as household waste. It should be handed to an
appropriate collection point for the recycling of electrical and electronic
equipment. Contact your local council or household waste disposal service for
further information.
Do not dispose of electrical appliances as unsorted municipal waste, use
separate collection facilities.