viveroo SquareDock User manual
Safety information
!
!! WARNING
Please read the assembly instructions included carefully. Please
read this SquareDock user manual completely before using your
SquareDock. Please follow the instructions and recommendations
to ensure proper use and maximum enjoyment.
Safety
information
SquareDock and all SquareDock mounting sets are intended for use
in enclosed and dry living spaces.
The following conditions must be provided:
- Operating temperature between 0° C (32° F) and 35° C (95° F).
- Relative humidity (during use): 20 % to 90 %, non-condensing.
- No external environmental influences such as oil, chemicals, salt,
extensive dust, etc.
Installation, service or repairs, if necessary, may only be performed
by authorized persons.
The installer is responsible for selecting the proper mounting
location and safe installation of SquareDock. This also applies to
installation in movable parts, such as doors. The installer is
responsible for performing and documenting all necessary safety
tests.
All electrical installation work may only be conducted by
authorized, trained electricians, always adhering to the general rules
and regulations applying to electrical installation.
Should it become apparent that safe operation of SquareDock is not
assured, then SquareDock must immediately be taken out of service
and secured against potential misuse. If the SquareDock functions
are limited, blocked or disabled, if an unusual odor is present, if
noises such as scratching are audible or damage is visible, safe
operation can no longer be guaranteed.
Technical Data
Measurements
Measurements design cover
364 x 294
Depth SquareDock
36
Size of opening (for furniture installation)
Size of opening (for flush-mounted box)
367 x 296,5
344 x 271
Installation depth (for furniture installation)
Installation depth (for flush-mounted box)
36
76
Weight in kg
SquareDock
3,8
Electrical
connections
Low voltage
Power consumption
10-18 Vdc!
15 Watt
Removal from
power supply
SquareDock may be removed from the power supply via the circuit
breaker in the respective rooms.
CE & Co.
All SquareDocks have CE certification. SquareDock is quality
"Made in Germany". We use only high quality parts and
components produced by market leaders. SquareDock customers
are proud of their iPad Garage.
Technical changes and mistakes are excepted.
Product
contents
- User manual SquareDock
- SquareDock
Please note! External cable, power supply and mounting screws are
included in SquareDock MountingSet.
Compatability
Electrical operation of SquareDock is permitted only in connection
with SquareDock MountingSet and power supply and cable
included in the Mounting Set. Operation of SquareDock without a
MountingSet will lead to immediate loss of guarantee and warranty.
Operation
!
Funktionen
Click It! iPad-LadClick It! Opening the iPad
shelf
Open the iPad resting shelf by using the SquareDock button. Now
you can remove or insert your iPad.
!! IMPORTANT!!: SquareDock can be either installed vertically or
horizontally. The suspension of the resting shelf has been set to
wall position. For horizontal (i.e. table) or diagonal (i.e. lectern,
teacher's desk, control panel) installation, special adapter sets are
available on request.
Care and
Cleansing
Cleanse your SquareDock as needed with a soft micro fiber cloth
and clear water only. Dampen the micro fiber cloth and wipe the
surfaces gently. If necessary, you may remove the rubber pads (see
"Mounting").
The glass surfaces of DeepBlack and ClearWhite may also be
cleaned with standard glass cleaners.
!! WARNING!!: The interior of the SquareDock must remain dry.
To ensure this, use only a damp cloth for cleansing.
!! WARNING!!: Never scratch, scrape or scrub SquareDock
surfaces with abrasive materials.
Installation
Use the corresponding MountingSet to install your LoopDock. All MountingSets come with
specific mounting instructions.
Step 1
Carefully remove the lower rubber pad first and then the upper
rubber pad.
Proceed as follows:
- Open the iPad resting shelf by pressing the button down
completely. If the SquareDock is in a horizontal position, the shelf
must be gently lifted manually.
- Lift the lower rubber pad starting from the center of the
SquareDock (see photo). When the inlay has reached
approximately a 45° angle it can be carefully pulled out.
- Close the resting shelf and gently pull the upper rubber cushion
out.
Step 2
Carefully remove the four screws on the cover (see photo - green).
!! IMPORTANT: Hold cover tightly when removing the final screw
to avoid damage from falling down.
Step 3
Carefully remove the cover by lifting it towards you and place the
cover in a safe spot.
Step 4
Plug the connecting cable from the MountingSet into the
SquareDock plug contact.
!! WARNING: When inserting the SquareDock, make sure that the
connecting cable is not pinched or pulled, as this may damage the
cable.
!! WARNING: If a power supply is located close to the SquareDock,
please connect the protective grounding wire (yellow) to the
protective conductor of the power supply. (for example InWall
MountingSet)
Step 5
The various fastening points for the SquareDock are easily
identifiable (red). Using the screws included in the MountingSet,
fasten the SquareDock.
!! IMPORTANT: Please follow the instructions included with the
MountingSet.
Step 6
Place the cover on the SquareDock. The correct positioning is
dictated by the button. Thread the cover into place there. Fasten the
cover with the four screws and put the rubber pads back in place.
Warranty
Warranty
SquareDock comes with a two year warranty from date of purchase by the
original end customer, unless the device was repaired or replaced during the
warranty period. In this case, the warranty is valid until the end of the
regular two year warranty or six months following the repair/replacement,
whichever comes first.
Warranty claims and
verification
Should your SquareDock for any reason not perform as expected, please
contact your dealer and provide the original invoice with serial number as
well as a brief description of your complaint.
Warranty claims and
verification
The following devices are excluded from the warranty
Devices with damages caused by:
- acts of nature,
- misuse, including but not limited to disregarding the user manual and
mounting instructions,
- inappropriate handling,
- connection to an incorrect power supply,
- repairs or attempted repairs by unauthorized persons,
- use of the device in connection with third party products,
- devices on which the serial number of the producer has been changed,
deleted, removed or made illegible.
iPad® is a registered trademark of Apple Inc.
Table of contents
Other viveroo Rack & Stand manuals
