Viviox ZEBRA Z1000 Quick start guide

Installation and Operational Guide
Please read the manual below for important information on your Viviox
product that could prevent damage or serious injury. Faliure to follow our
instructions and other safety precautions could result in serious injury to
you or your passengers, and/or product and vehicle damage.
Important: The installation technician and operator must read this manual
before starting installation or operation of your new product. They must
have a thorough understanding of automotive systems, electronics and
procedures.
WARNING: Please understand that the user and installer assume
ultimate, complete and full responsibility in determining proper mounting
location and positioning. When installing, consider a location based on its
ability to proide total safety to all passengers.
WARNING: DO N OT USE CIRCUIT BREAKERS WITH THI S
PRODUCT! All customer-supplied wires that connect with the
positive (+) end of the battery must be able to support 125% or more of the
maximum operating current. They MUST be fused with the battery to
handle the current.
Before drilling and installation, check both sides of your mounting
service.
Gromments should be installed into all wire passage holes.
Please read your vehicle’s owner’s manual; it contains important
information about the airbag deployment area. This product should
NOT, under any circumstances, be installed in the deployment area of
the vehicle’s airbag. Do NOT route any wires in this area. Having
equipment mounted or located in this area is a serious risk; it could
reduce or damage the airbag’s effectiveness, or even become a
projectile that could result in serious injury or death.
This device may feature powerful, bright, high-intensity LED lights. DO
NOT look at the lights directly, as momentary blindness and\or
permanent eye damage can occur.
DO NOT try to activate or control this product during a hazardous or
dangerous driving situation.
If your device is controlled or activated by a remote, please double
check that the control is in a place that will allow for both the control
itself, as well as the vehicle, to be used safetly in any driving condition
and/or situation.
SPECIFICATIONS
Dimensions: 19.48”L x 5.31”W x 1.1”H
Input Voltage: 10-30 VDC Input Current: 16A Max @ 12V
Zebra
Model Z1000

applying power
to the yellow wire.
RED
Positive
BLACK
Negative
YELLOW
To +VDC - Patterns
BROWN
To +VDC - Warning Mode
ORANGE
To +VDC - Left Arrow
BLUE
To +VDC - Right Arrow
ORANGE + BLUE
To + VDC - Center Out
GREEN
To + VDC - Takedown
Visor
Passenger Side
Bracket
Center
Bracket
Center
Bracket
Driver
Side Bracket
Zebra
Use supplied mounting brackets to attach light bar to the vehicles visor.

P1- One Lamp Sequence to Double
P2- Two Lamp Sequence to Double
P3- Six Lamp Sequence to Double
P4- Sequence to Solid
P5- One Lamp Sequence to Triple
P6- Triple Lamp Sequence to Double
P7- Sequence On to Sequence Off
P8- Solid Arrow
TRAFFIC ADVISOR PATTERNS
P1- Double 75FPM Half Double 75FPM Checker 75FPM
P2- Half Double 75 FPM Checker 75FPM
P3- 4 Dual Double 75FPM Half Double 75FPM Checker 75FPM
P4- 4 Dual Double 75FPM
P5- 4 Dual Double 150FPM Half Double 150FPM Checker 150FPM
P6- Double 150Fpm Half Double 150FPM Checker 150FPM
P7- 4 Dual 75FPM Half Double 75FPM Checker 75FPM
P8- Double 35FPM Half Double 35FPM Checker 35FPM
P9- Single Flash 75FPM
P10- Single 150FPM
P11- Double Flash 75FPM
P12- Double Flash 120FPM
P13- Quad Flash 75FPM
P14- Quad Flash 150FPM
P15- Single Flash Split 75FPM
P16- Single Flash Split 150FPM
P17- Double Flash Split 25FPM
P18- Double Flash Split 150FPM
P19- Quad Flash SpLit 75FPM
P20- Quad Flash Split 150FPM
P21- Single 600FPM Checker
P22- Quad 150FPM Checker
P23- 4 Single 150FPM 4 Single 300FPM Half
P24- 3 Single 150FPM 3 Double 150FPM 3 Single 300FPM Half
P25- In Out 150FPM
P26- In Out 75FPM
P27- Steady Quad 150FPM Checker
P28- Steady Quad 75FPM Checker
P29- Modul. Checker
P30- Single 75/150/300FPM Checker & all on
P31- Auto
WARNING FLASH PATTERNS