Viviox Pandora H600 User manual
FLASH PATTERNS
1: Single 120 FPM Ph1-Color 1&2
2: Single 120 FPM Ph2-Color 1&2
3: Single 120 FPM Ph1-Color 1
4: Single 120 FPM Ph2-Color 2
5: Single 120 FPM Alt. Color 1<-->2
6: Single 300 FPM Ph1-Color 1&2
7: Single 300 FPM Ph2-Color 1&2
8: Single 300 FPM Ph1-Color 1
9: Single 300 FPM Ph2-Color 2
10: Single 300 FPM Alt. Color 1<-->2
11: Single 75 FPM Ph1-Color 1&2
12: Single 75 FPM Ph2-Color 1&2
13: Single 75 FPM Alt. Color 1<-->2
14: Double 75 FPM Ph1-Color 1&2
15: Double 75 FPM Ph2-Color 1&2
16: Double 75 FPM Alt. Color 1<-->2
17: Double 120 FPM Ph1-Color 1&2
18: Double 120 FPM Ph2-Color 1&2
19: Double 120 FPM Alt. Color 1<-->2
20: Quad 75 FPM Ph1-Color 1&2
21: Quad 75 FPM Ph2-Color 1&2
22: Quad 75 FPM Ph1-Color 1
23: Quad 75 FPM Ph2-Color 2
24: Quad 75 FPM Alt. Color 1<-->2
25: Quad 120 FPM Ph1-Color 1&2
26: Quad 120 FPM Ph2-Color 1&2
27: Quad 120 FPM Ph1-Color 1
28: Quad 120 FPM Ph2-Color 2
29: Quad 120 FPM Alt. Color 1<-->2
30: Quint 120 FPM Ph1-Color 1&2
31: Quint 120 FPM Ph2-Color 1&2
32: Quint 120 FPM Alt. Color 1<-->2
33: 2 Double 75 FPM, 4 Quad 120 FPM
34: Module Flash Color 1<-->2
35: AUTORUN
36: STEADY BURN
37: OFF
Installation and Operational Guide
BLACK
GND-Ground
BLUE
Pattern
YELLOW
Sync
RED
Positive
OPERATION
1. Operation Instructions (see diagram above:
In order to activate your Pandora, connect the red wire to a 12V post
and the black wire to the ground post of the vehicle's battery.
Less then a second
1-3 Seconds
3-5 Seconds
5+ Seconds
Next Pattern
Previous Pattern
Factory Default
Turn off and Reset
1. Syncing Instructions: Configure both Pandora's to the same pattern in Phase 1
and connect the yellow wires from each light head together.
2. To have your Pandora's alternate: Set every other light to the same pattern in
Phase 2 and connect the yellow wires. To better understand how this feature works,
each light head coming from the factory will display Phase 1.In order to have one
Pandora alternate with another, every other light needs to be advanced to Phase 2
of the current pattern.
2. Changing Patterns:
Patterns can be changed by momentarily connecting the blue wire to
the ground of your vehicle's battery.
Please read the manual below for important information on your Viviox
product that could prevent damage or serious injury. Failure to follow our
instructions and other safety precautions could result in serious injury to
you or your passengers, and/or product and vehicle damage.
Important: The installation technician and operator must read this manual
before starting installation or operation of your new product. They must
have a thorough understanding of automotive systems, electronics and
procedures.
WARNING: Please understand that the user and installer assume
ultimate, complete and full responsibility in determining proper mounting
location and positioning. When installing, consider a location based on its
ability to provide total safety to all passengers.
WARNING: DO NOT USE CIRCUIT BREAKERS WITH THIS
PRODUCT! All customer-supplied wires that connect with the
positive (+) end of the battery must be able to support 125% or more of the
maximum operating current. They MUST be fused with the battery to
handle the current.
ŸBefore drilling and installation, check both sides of your mounting
service.
ŸGrommets should be installed into all wire passage holes.
ŸPlease read your vehicle's owner's manual; it contains important
information about the airbag deployment area. This product should
NOT, under any circumstances, be installed in the deployment area of
the vehicle's airbag. Do NOT route any wires in this area. Having
equipment mounted or located in this area is a serious risk; it could
reduce or damage the airbag's effectiveness, or even become a
projectile that could result in serious injury or death.
ŸThis device may feature powerful, bright, high-intensity LED lights. DO
NOT look at the lights directly, as momentary blindness and/or
permanent eye damage can occur.
ŸDO NOT try to activate or control this product during a hazardous or
dangerous driving situation.
ŸIf your device is controlled or activated by a remote, please double
check that the control is in a place that will allow for both the control
itself, as well as the vehicle, to be used safely in any driving condition
and/or situation.
Model H600
Pandora Series
T. 844.3.VIVIOX
W. www.VIVIOX.com
E. support@VIVIOX.com
Surface Mounting (See Figure 1.)
1. Position the light unit with the flange attached on the mounting surface and mark
the position of the two screws and a center wire passage hole.
2. Drill two holes for the screws and a 0.5” center wire passage hole.
3. Place the light unit on the mounting surface and secure it with the included
hardware.
MOUNTING
SPECIFICATIONS
Dimensions: 0.99” H, 1” D
Input Voltage: 10-30VDC Input Current: 1.4A (MAX)
Headlight or Tail Light Mounting (See Figure 2.)
1. Refer to your vehicle's manual for instructions on how to remove the headlight or
taillight assembly.
2. Select the mounting location and choose a surface in the bottom or rear of the
light assembly as close to the focal point as possible. Be sure that it doesn't
interfere with the operation of the light.
3. Use a saw to cut a 1” hole in the chosen location. Insert the light unit into the hole
and mark the location of the two screw sockets. Remove the light and drill the two
holes.
4. Place the gasket on the light and insert it in the hole. Use metal screws to secure
it to the light assembly.
5. Reinstall the headlight or taillight assembly and route the wires to their
appropriate control switches.
Optional Brackets
Figure 2.
Figure 1.
Table of contents
