Vivo STAND-E-149 User manual

Electric Single Ultrawide
Monitor Desk Mount
Instruction Manual
SKU: STAND-E-149
Assembly Video & Product Info
www.vivo-us.com/products/stand-e-149

Contact Us First!
PERSONABLE CUSTOMER SUPPORT
Our friendly product support team is here to help!
DO NOT RETURN ITEM
We’re Here for You!
Missing a Part?
Our customer-minded support team is here for YOU,
Monday-Friday 7am-7pm CST.
We oer immediate assistance with rapid response times
from customer service agents and product techncians to
help you every step of the way!
Monday-Friday
Chat Us:
www.vivo-us.com
Give us a Call:
309-278-5303
Email Us:
[email protected]om
If any parts are received damaged / defective OR you are
missing a part, please reach out to us within 30 days of
product delivery to have it replaced at no cost.
We are happy to replace parts to ensure you have a fully
functioning product
7AM - 7PM

Product Warranty
Returns | Product Didn’t Work Out?
For the most up to date details on your product’s warranty, please visit
the product’s listing on our website or reach out to customer support.
vivo-us.com/products/stand-e-149
We oer a hassle-free 30 day return on all products. Contact customer
support at 309-278-5303 or [email protected]om. Please note: For items
ordered in error or no longer needed, the return shipping charges will
be at the buyer’s expense.
If you do not understand these directions, or if you have any doubts about the safety of the installation, please contact our product
support team at 309-278-5303 or [email protected] for further assistance. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly
specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting,
incorrect assembly or inappropriate use.
LBS
CAUTION!
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
DO NOT EXCEED WEIGHT CAPACITY
FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY.
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND
ELECTRIC SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR SELLER TO
REPLACE DAMAGED PARTS.
• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE MADE
CONTACT WITH LIQUIDS.
• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
• OUTDOOR USE IS PROHIBITED.
ELECTRICAL SAFETY INSTRUCTIONS

4
Package Contents
Included Hardware & Tools
F (x1)
VESA Plate
A (x1)
Electric Stand
B(x1)
Lower Clamp
Bracket
C(x1)
Upper Clamp
Bracket
D(x1)
Clamp Cable Clip
E(x1)
Arm Bracket
G (x1)
Cable Sleeve
H (x1)
AC Adapter
I (x1)
Power Cable
J (x1)
Control Panel
K (x1)
Power Cable
S-A (x4)
M6x12mm
Screw
S-B(x1)
Screw Cap
S-C (x1)
M3x8mm
Screw
M-A (x4)
M4x12mm
Screw
M-C (x4)
M5 Washer
T-A (x1)
4mm Allen
Wrench
M-B (x4)
M5x12mm
Screw
T-B (x1)
6mm Allen
Wrench
L(x1)
Large Pad
M(x2)
Small Pad N(x2)
Cable Clip
S-D (x2)
ST3.5x18mm
Screw

5
Phillips
Screwdriver
Pencil
Drill
Scissors
Tools Needed: Weight Capacity:
22lbs
(10kg)

6
ASSEMBLY STEPS
STEP 1
SECURE CLAMP BRACKET
Attach Upper Clamp Bracket (C) to the bottom of the Electric Stand (A) using M6x12mm
Screws (S-A) and 4mm Allen Wrench (T-A). Remove protective film from Large Pad (L) then
attach it to the bottom of the stand.
A(x1)
C(x1)
L(x1)
S-A (x4)
T-A
T-A
L
S-A
C
A

7
STEP 2 A. DESKTOPS 10-55mm (0.40”-2.15”)
FOR DESKTOPS 10-55mm (0.40”-2.15”)
Align the key slots on Lower Clamp Bracket (B) with the screws on Upper Clamp Bracket (C).
Pull Lower Clamp Bracket (B) down and lock the screws on Upper Clamp Bracket (C) in place
with the 4mm Allen Wrench (T-A).
PROCEED
TO STEP 3
B(x1)
6mm
10mm-55mm
T-A
B
C
T-A

8
FOR DESKTOPS 50-85mm (2”-3.35”)
Remove the screws on Upper Clamp Bracket (C) and reassemble them into the lower set of
holes using 4mm Allen Wrench (T-A).
Align the key slots on Lower Clamp Bracket (B) with the screws on Upper Clamp Bracket (C).
Pull Lower Clamp Bracket (B) down and lock the screws on Upper Clamp Bracket (C) in place
with the 4mm Allen Wrench (T-A).
T-A
T-A
STEP 2 B. DESKTOPS 50-85mm (2”-3.35”)
6mm
50-85mm
B(x1)
CT-A
C
B
T-A

9
T-A
D(x1)
STEP 3
STEP 4
SECURE CLAMP TO DESKTOP
Clamp the stand assembly onto desk and press the Clamp Cable Clip (D) onto Upper Clamp
Bracket (C).
ATTACH ARM BRACKET
Partially loosen the screw the on side of Arm Bracket (E) using 6mm Allen Wrench (T-B).
Slide Arm Bracket onto the post of Electric Stand (A) and secureusing 6mm Allen Wrench.
E (x1)
C
D
A
T-B
E

10
STEP 5
CONNECT VESA PLATE TO MONITOR
Attach VESA Bracket (E) to the monitor using either M4x12mm (M-A) or M5x12mm Screw
(M-B) and Washers (M-C) along with a Phillips Screwdriver.
M-A (x4)
M-B (x4)
M-C (x4)
F (x1)
or
F
M-C
M-A
M-B

11
STEP 6
S-C (x1)
S-B (x1)
SECURE MONITOR ON STAND
Slide the monitor onto tilt joint of the Arm Bracket (E) and lock VESA Plate (F) in place
using Screw Cap(S-B), M3x8mm Screw (S-C) and a Phillips Screwdriver. Adjust monitor
height alignment by turning Screw Cap by hand or using 6mm Allen Wrench (T-B).
T-B
S-C
S-B
T-B

12
STEP 7
ADJUST TILT JOINT
The tilt-joint has been pre-tightened and larger monitors may tilt upward when mounted.
Slowly adjust the monitor angle downward by hand until it is at your desired angle.
If you go past your desired angle and want to adjust the monitor angle upward, use 6mm Allen
Wrench (T-B) to loosen the tilt-joint then adjust monitor to desired angle and retighten the tilt-joint.
Large monitors can be very diicult to adjust by yourself.
Please use caution and have someone assist you with
adjusting your monitor to avoid possible damage or injury.
WARNING
T-B
PLEASE FOLLOW THESE STEPS FOR ALL
FUTURE ADJUSTMENTS TO PREVENT
POSSUBLE DAMAGE OR INJURY.

13
STEP 8
K (x1)
CONNECT POWER
Connect cables between Electric Stand (A), Control Panel (L), Splitter Cable (M), AC
Adapter (J), and Power Cable (K) as shown below.
Note: Extra Cable (L1) relates to a feature not available on this product and is le unconnected.
For more information, please contact Product Support at 309-278-5303 or [e-mail].
L1

14
STEP 9
CONNECT CONTROL PANEL TO DESKTOP
Attach the Control Panel (J) to the underside of the desktop using ST3.5x18mm Screws (S-D)
as shown. Remove protective film from Cable Clip (N) and secure the Extra Cable (J1) to the
desktop.
J (x1)
M (x1)
N (x3)
S-D (x2)
H (x1)
If desired, attach AC Adatper (H) to desktop using Small Pad (M), making sure the protective
film is removed.
S-D
J
J1
M
H

15
1
STEP 10
SETUP PROCEDURE
The stand will now be setup for electric height adjustments.
1. Set Device Display: Press and hold the “M” button on Control Panel for 2 seconds.
The screen should display 39.0cm. If the display shows 73.0cm, press and hold the “M”
button for 2 seconds again. Note: the 73.0 corresponds to a feature not available on this
product.
2. Adjust Desk Height (if applicable): If you are using a height adjustable desk,
move your desk to a comfortable sitting height. It is recommended to follow general
ergonomic guidelines for working posture while considering your desk frame height.
3. Calibrate Li: Press and hold on the Control Panel and bring the stand up to it’s
highest point (52.0 on screen), then press and hold . The stand will return back it it’s
lowest setting (39.0) and then move back up slightly.
3. Set Sitting Height: Loosen Arm Bracket (E) using 6mm Allen Wrench (T-B). Manually
adjust the Bracket along pole until the top of the monitor screen is at eye level while in
your normal sitting position. In some cases, the Bracket may be positioned at the very
top or the very bottom of the electric stand post respectively. Re-tighten the arm bracket
screw to secure the arm assembly in this position.
4. Save Sitting Height: Press the key and “S-” will be displayed on screen. Now
press the key within five seconds to save your preferred sitting height. This can be
adjusted later if desired. Please refer to Control Panel instructions on Page 19.
“Why do I have to set the monitor manually first?”
T-B
?
Because a comfortable viewing height is 3-4” higher when you are standing, the sitting
height of your monitor is initally set manually. This allows the motorized adjustment to be
more personalized when adjusting for standing height. Going forward, the monitor can be
set electrically for both sitting and standing.
T-B
E

16
STEP 11
SETTING VIEWING HEIGHT FOR STANDING
Set your height adjustable to a comfortable standing position. Then press on Control
Panel to adjust the montior to a comfortable ergonomic viewing height while standing.
Press the and “S-” will be displayed. Now press the key within five seconds to save your
preferred standing height.
Repeat this process to store a third working posture in memory setting 3if desired. This can
be adjusted later if needed. Please refer to Control Panel instructions on Page 19.
2

17
STEP 12
ROUTE CABLES
Route cables through Cable Sleeve (K). Make sure there is enough slack in the cables and
sleeve when the electric stand is at its tallest height. Run Cable Sleeve down the back of the
stand and secure into Clamp Cable Clip (D).
K (x1)
K
D

18
+90° to -90° Tilt 360° Swivel
360° Rotation
ADJUST AS DESIRED
Large monitors can be very diicult to adjust by yourself.
Please use caution and have someone assist you with
adjusting your monitor to avoid possible damage or injury.
WARNING

19
CONTROL PANEL INSTRUCTIONS
UPWARD AND DOWNWARD MOVEMENT
Press and hold the or until the monitor reaches the desired height.
MEMORY PRESETS
The control panel features 3 memory presets that allow you to save a height setting to easily
return to it.
1. Press and “S-” will be displayed.
2. Press 1, 2, or 3within five seconds to store the current device height in
memory.
Each number can store a dierent height. Once desired memories are set, you
can recall any of the three height settings by pressing the corresponding number
button. Touching any button will stop the automatic adjustment.
RESET PROCESS
If screen diplay height does not match the monitor height, a reset can be performed.
Press and hold on the Control Panel and bring the stand up to it’s highest point (52.0
on screen), then press and hold . The stand will return back it it’s lowest setting (39.0)
and then move back up slightly.

20
TIMED REMINDER MODE
Set a timer to remind you to transition from sitting to standing or vice verse.
SLEEP MODE
Sleep mode turns o the screen display aer 1 minute, helping to prevent accidental
operation. To exit, simply touch the screen and the control panel will awake.
TROUBLESHOOTING
SWITCH THE DISPLAY FROM CENTIMETER TO INCH
The control panel is set to CM by default. To switch it to Inch, follow these steps.
1. Press and the screen will flash “0.5h” representing 30 minutes.
2. Press repeatedly to increase 0.5 hours at a time.
The maximum timer setting is 2 hours. The timer is set when the display stops
flashing and the indicator light in the top right corner of the controller is on.
When the timer has reached the set time, three beeps will sound reminding the
user to adjust the working position. Once the timer setting has expired, the unit’s
timer is canceled.
3. To deactivate the timer, press five times or until the current height is
displayed and the indicator light in the upper right corner is turned o.
1. Restart the system by unplugging the unit for at least 5 seconds, then plug it
back in.
2. Press and hold for at least 3 seconds
The control panel will beep twice (beeps twice if changing to inch, and beeps once
changing to cm) and change the displayed unit. Repeat to switch back from inch
to cm.
Error Code Description/Resolution
ER6 Connection error between control panel and electric monitor arm cable. Reconnect the
USB cable and the connecter. Ensure the USB cable is being routed away from the cable
sleeve and outside the cable clip to avoid any interference.