Vivo STAND-TV65A User manual

Easel Studio TV Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-tv65a
SKU: STAND-TV65A/AB/AW
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2 3
PACKAGE CONTENTS
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
ASSEMBLY STEPS
STEP 1
Screw Side Legs (A) and Center Leg (B) into base of Pole (E).
TOOLS NEEDED
Phillips
Screwdriver
STEP 2
Adjust collar height using the 4mm Allen Wrench (T-A).
Drill
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF TV OR STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
A
A
B
E
L
NOTE: Please secure the locking
collar before attaching the TV
screen.
Recommended 50-150mm
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
70.4lbs
(32 kg)
NORMAL FLOOR
55 lbs
(25 kg)
GLOSSY FLOOR
Tape Measure Level Pencil
A (x2)
Side Leg
B(x1)
Center Leg
C(x1)
Lower VESA
Bracket
E (x1)
Pole
D(x1)
Upper VESA
Bracket
G (x1)
Steel Cable
M-H (x2)
Security Clip
H (x2)
Security Clip
Clamp
F(x2)
Cable Clip
S-A (x2)
ST4.2x12
Screw
T-B x1)
2mm Allen
Wrench
T-A (x1)
4mm Allen
Wrench
W-A (x4)
ST4.8x38
Screw
W-B (x4)
Anchor
M-A (x4)
M6x14mm
Screw
M-B (x4)
M8x16mm
Screw
M-C (x4)
M6x30mm
Screw
M-D (x4)
M8x35mm
Screw
M-F (x8)
Small Spacer
M-G (x8)
Big Spacer
W-C (x2)
D5 Washer
T-A
M-E (x4)
M8 Washer

4 5
STEP 3
Remove Screw (C1) from center clamp of lower VESA Bracket (C) and open the clamp.
STEP 4
OPTION A: Flat Back Monitor
Position Upper Bracket (C) over top holes on TV and secure using Screws (M-A thru M-D), Security Clips
(M-I), M8 Washers (M-E) and a Phillips screwdriver. Secure Lower Bracket (D) using Screws (M-A or
M-B), M8 Washers (M-E), and Phillips screwdriver. Spacers (M-F, M-G) may also be required.
C
STEP 5
Slide the TV with VESA Brackets (C, D) onto Pole (E). Close the clamp on Lower VESA
Bracket (C) over the pole and secure with previously removed Screw (C1).
1100 mm
C1
STEP 6
Peel backing from Cable Clips (G) and install clips on rear leg. Use clips to organize cables.
Optional: Secure cable clips using ST4.2x12 Screws (S-A). Screws are able to thread directly into
wood without drilling pilot holes.
J
1
2
3
I
S-A
G
C1
C
M-H M-H
C
D
C
D
C1

6 7
P-C
1100-1350mm
400-650mm
40mm
(1.6”)
ø 7mm
(ø 9/32”)
STEP 7
OPTION A: Wood Stud Installation
Use a stud finder and a level to locate two adjacent studs. Using Security Cable Clamps (H) as
guides, mark drilling locations on the wall. Drill a 1.6” (40mm) deep hole using a 1/8” (3.5mm) drill
bit. Mount Security Cable Clamps (H) to wall using ST4.8x38 screws (S-A). Thread Steel Cable (G)
through Security Clip (M-H), then through the center holes in the Security Cable Clamps (H) as
shown, then tighten Clamps (H) using the 2mm Allen Wrench (T-A).
P-B
P-A
P-D
P-A
P-C
STEP 7 (Continued)
mJ
mJ_
mJa
mJ^
OPTION B: Concrete/ Brick Installation
Using Security Cable Clamps (H) as guides, mark drilling locations on wall. Drill holes at least 1.6”
(40mm) deep using a 9/32” (7mm) drill bit. Insert anchors (W-B) in holes and mount Cable Clamps (H)
to wall using ST4.8x38 Screws (W-A). Thread Steel Cable (G) through Security Clips (M-H) and through
the center holes in the Cable Clamps (H) as shown, then tighten Clamps (H) using the 2mm Allen
Wrench (T-B).
W-B
W-A
H
mJ_
M-H
G
T-B
G
H
H
1100-1350mm
400-650mm
= F
QM
NK
40mm
(1.6”)
W-A
H
ø 3.5mm
(ø 1/8”)
M-H
G
T-B
G
H

LAST UPDATED: 02/07/2023
REV6
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303