VocoPro DJ-Smart-LightShow User manual

owner’s manual
Smart 5 in 1 Multi-Effect DJ Light
DJ-Smart-LightShow

2 \
WELCOME
And thank you for purchasing our DJ-Smart LightShow from VocoPro. Along with quality products our commitment
to customer satisfaction means we have technical support professionals ready to assist you. Be sure to visit our website-
www.vocopro.com for the latest information on new products.
Model Number
Serial Number
Date of Purchase
Place of Purchase
Please record the model number and serial number below, for easy reference, in case of loss or theft. These
numbers are located on the packaging the item came in. Space is also provided for other relevant information.
We are at:
VocoPro
1728 Curtiss Court
La Verne, CA 91750
Phone:
Toll Free: 800-678-5348
TEL: [phone]
FAX: [phone]
E-mail:
[email protected]
Tech Support
[email protected]
All rights reserved. Information, specifications, diagrams, images, and instructions herein are subject to change
without notice. VocoPro Products, logo and identifying product names and numbers herein are trademarks of VocoPro.
Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by
statutory or judicial law or hereinafter granted. Product names used in this document may be trademarks or registered
trademarks of their respective companies and are hereby acknowledged. All non-VocoPro Products, brands and
product names are trademarks or registered trademarks of their respective companies.
VocoPro hereby disclaims any and all liabilities for property, equipment, building, and electrical damages, injuries to any
persons, and direct or indirect economic loss associated with the use or reliance of any information contained within
this document, and/or as a result of the improper, unsafe, insufficient and negligent assembly, installation, rigging, and
operation of this product.
Legal Disclaimer

/ 3
Laser Warnings and Safety
NON-INTERLOCKED HOUSING WARNING
The DJ Smart-LightShow contains high power laser devices internally. Do not open the laser housing due to potential
exposure of unsafe levels of laser radiation. The laser power levels, if the unit is opened, can cause instant blindness,
skin burns and fires.
STOP AND READ ALL LASER SAFETY DATA
OPERATION INSTRUCTIONS AND LASER SAFETY
The light source emitted from this product can potentially cause eye injury if not set up and used properly. The light
source emitted from a laser is very different from any other light sources with which you may be aware of. Laser light is
thousands of times more concentrated than any light from any other kind of light source. This concentration of light can
cause instant eye injuries, primarily by burning the retina (the back of your eyeball containing cells that are sensitive to
light). Even if you cannot feel “heat” from a laser beam, it can still potentially injure or blind you or your audience. Even
very small amounts of laser beam light are potentially hazardous even at long distances. Laser eye injuries can be
sustained faster than you can blink.
PRECAUTIONS
• Do not think that because this laser splits the laser beam into hundreds of beams and that the laser beam is scanned
out in high speed, that an individual laser beam is safe for eye exposure. This laser uses milliwatts of laser power
before it splits into multiple beams. Many of the individual beams are potentially hazardous to the eyes.
• Do not think that because the laser light is moving, it is safe. Be aware that laser beams do not always move. Since
eye injuries can occur instantly, it is critical to prevent even the smallest possibility of any direct eye exposure. In the
laser safety regulation, it is not legal to aim lasers in areas which people can get exposed. This is true even if it is
aimed below people’s faces, such as on a dance floor.
• Do not operate the laser without first reading and understanding all safety and technical data in this manual.
• Always set up and install all laser effects so that all laser light is at least 3 meters (9.8 feet) above the floor on which
people can stand.
• After setting up, and before public use, test laser to ensure proper function. Do not use if any defect is detected. Do
not use if laser emits only one or two laser beams rather than dozens/hundreds, as this could indicate damage to the
diffraction grating optic and could allow emission of higher laser levels above Class 2
• Do not point lasers at people or animals. Never look into the laser aperture or laser beams.
• Do not point lasers in areas in which people can potentially get exposed, such as uncontrolled balconies, etc. Do not
point lasers at highly reflective surfaces, such as windows, mirrors and shiny metal. Laser reflections can
be hazardous.
• Never point a laser at aircraft, this is a federal offense.
• Never point unterminated laser beams into the sky.
• Do not expose the output optic (aperture) to cleaning chemicals.
• Do not use laser if the laser appears to be emitting only one or two beams.
• Do not use the laser if the housing is damaged, the housing is open, or if the optics appear damaged in any way.
• Never open the laser housing. The high laser power levels inside of the protective housing can start fires, burn skin
and will cause instant eye injury.
• Never leave this device running unattended.
• The operation of a class 2 laser show is only allowed if the show is controlled by a skilled and well- trained operator,
familiar with the data included in this manual.
• The legal requirements for using laser entertainment products vary from country to country. The user is responsible for
the legal requirements at the location/country of use.
• Always use proper lighting safety cables when hanging lights and effects overhead.

4 \
Safety Instructions
1. Read Instructions - All the safety and operating
instructions should be read before the appliance is
operated.
2. Retain Instructions - The safety and operating
instructions should be retained for future reference.
3. Heed Warnings - All warnings on the appliance and in
the operating instructions should be adhered to.
4. Follow Instructions - All operating and use instructions
should be followed.
5. Attachments - Do not use attachments not
recommended by the product manufacturer as they may
cause hazards.
6. Water and Moisture - Do not use this unit near water. For
example, near a bathtub or in a wet basement and the like.
7. Carts and Stands - The appliance should be used
only with a cart or stand that is recommended by the
manufacturer.
7 A. An appliance and cart combination should be
moved with care. Quick stops, excessive force, and uneven
surfaces may cause an overturn.
8. Ventilation - The appliance should be
situated so its location does not interfere
with its proper ventilation. For example, the
appliance should not be situated on a bed,
sofa, rug, or similar surface that may block
the ventilation slots.
9. Heat - The appliance should be situated away from heat
sources such as radiators, heat registers, stoves, or other
appliances (including ampliers) that produce heat.
10. Power Sources - The appliance should be connected to
a power supply only of the type described in the operating
instructions or as marked on the appliance.
11. Grounding or Polarization - Precautions should be
taken so that the grounding or polarization means of an
appliance is not defeated.
12. Power-Cord Protection - Power-supply cords should be
routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles, and
the point where they exit from the appliance.
13. Cleaning - Unplug this unit from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
14. Power lines - An outdoor antenna should be located
away from power lines.
15. Non-use Periods - The power cord of the appliance
should be unplugged from the outlet when left unused for a
long period of time.
16. Object and Liquid Entry - Care should be taken so
that objects do not fall and liquids are not spilled into the
enclosure through openings.
17. Damage Requiring Service - The appliance should be
serviced by qualied service personnel when:
A. The power supply cord or plug has been damaged; or
B. Objects have fallen into the appliance; or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or
exhibits a marked change in performance; or
E. The appliance has been dropped, or the
enclosure damaged.
18. Servicing - The user should not attempt to service
the appliance beyond that described in the operating
instructions. All other servicing should be referred to
qualied service personnel.
The lightning ash & arrowhead symbol,
within an equilateral triangle, is intended to
alert you to the presence of danger.
The exclamation point within an
equilateral triangle is intended to alert you
to the presence of important operating and
servicing instructions.
Explanation of Graphical Symbols
WARNING: To reduce the risk of re or electric shock,
do not expose this unit to rain or moisture.
CAUTION: To reduce the risk of electric shock, do
not remove cover (or back). No user-serviceable
parts inside. Only refer servicing to qualied
service personnel.
CAUTION
RISK OF SHOCK
Note: To CATV system installer’s (U.S.A.): This reminder
is provided to call the CATV system installer’s attention
to Article 820-40 of the NEC that provides guidelines for
proper grounding and, in particular, species that the
cable ground shall be connected as close to the point of
cable entry as practical.

/ 5
FCC Information
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!:
This product, when installed as indicated in the instructions
contained in this manual, meets FCC requirements.
Modications not expressly approved by Vocopro may void
your authority, granted by the FCC, to use this product.
2. IMPORTANT: When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable(s) supplied with this product MUST
be used. Follow all installation instructions. Failure to follow
instructions could void your FCC authorization to use this
product in the U.S.A.
3. NOTE: This product has been tested and found to
comply with the requirements listed in FCC Regulations,
Part 15 for Class “B” digital devices. Compliance with these
requirements provides a reasonable level of assurances
that your use of this product in a residential environment
will not result in harmful interference with other electronic
devices. This equipment generates/uses radio frequencies
and, if not installed and used according to the instructions
found in the owner’s manual, may cause interference
harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product
is found to be the source of interference, which can be
determined by turning the unit “Off” and “On”, please try
to eliminate the problem by using one of the following
measures:
Relocate either this product or the device that is being
affected by the interference.
Use power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line lter(s).
In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300-ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact your local retailer authorized to
distribute Vocopro products. If you can not locate the
appropriate retailer, please contact Vocopro,
1728 Curtiss Court, La Verne, CA 91750.
CAUTION:
READ THIS BEFORE OPERATING YOUR UNIT
1. To ensure the nest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2. Install your unit in a cool, dry, clean place - away from
windows, heat sources, and too much vibration, dust,
moisture or cold. Avoid sources of hum (transformers,
CAUTION: The apparatus is not disconnected from the
AC power source so long as it is connected to the wall
outlet, even if the apparatus itself is turned off. To fully
ensure that the apparatus is indeed fully void of residual
power, leave unit disconnected from the AC outlet for at
least fteen seconds.
NOTE: Please check the copyright laws in your country
before recording from records, compact discs, radio,
etc. Recording of copyrighted material may infringe
copyright laws.
Voltage Selector (General Model Only)
Be sure to position the voltage selector to match the
voltage of your local power lines before installing the unit.
electric motors). To prevent re or electrical shock, do
not expose to rain and water.
3. Do not operate the unit upside-down.
4. Never open the cabinet. If a foreign object drops into
the set, contact your dealer.
5. Place the unit in a location with adequate air
circulation. Do not interfere with its proper ventilation;
this will cause the internal temperature to rise and may
result in a failure.
6. Do not use force on switches, knobs or cords. When
moving the unit, rst turn the unit off. Then gently
disconnect the power plug and the cords connecting to
other equipment. Never pull the cord itself.
7. Do not attempt to clean the unit with chemical solvents:
this might damage the nish. Use a clean, dry cloth.
8. Be sure to read the “Troubleshooting” section on
common operating errors before concluding that your
unit is faulty.
9. This unit consumes a fair amount of power even when
the power switch is turned off. We recommend that you
unplug the power cord from the wall outlet if the unit is
not going to be used for a long time. This will save
electricity and help prevent re hazards. To disconnect
the cord, pull it out by grasping the plug. Never pull the
cord itself.
10. To prevent lightning damage, pull out the power cord
and remove the antenna cable during an electrical
storm.
11. The general digital signals may interfere with other
equipment such as tuners or receivers. Move the
system farther away from such equipment if
interference is observed.

6 \
What’s in the Box / Features
1.Smart 5 in 1 Multi-Effect DJ Light
2.AC Power Cord
3.Remote Control
Features:
• Smart 5 in 1 Multi-Effect DJ Light
• Power supply: AC100-240V,50-60Hz
• Power consumption: 30W
• Fuse: 250V
• MOONFLOWER LED: 6*3W RGB LEDs
• UV-White LED: 4*2W 2IN1 LEDs
• WATER WAVE: 1*4W RGBW LEDs
• LASER: Red + Green
• Beam Angle: 6°
• Play Mode: Auto, Sound-activated,Master/Slave,DMX512
• Package dimensions(L*W*H): 11.8x 8.3x 6.3 inches N.W: 2.65lb
• G.W: 3.09lb

/ 7
Safety Measures
3 Meters
9.8 ft
3 Meters
9.8 ft
Place DJ Smart Light Show 3
meters from floor to laser light.
In addition, place 3 meters
horizontally between laser light
and audience.
This unit is intended for indoor
use only, use of this product
outdoors voids all warranties.
Please mount securely and
disconnect power after use.
Warning! To prevent or
reduce the risk of electrical
shock or fire, do not expose
this unit to rain or moisture.
Caution! This may cause eye
damage. Avoid looking directly
into the light source. Use
sensible precaution.
If using a DMX
controller use of a DMX
signal terminator will
reduce signal errors,
transmission problems,
and interference. DMX
cable use only. Do not
plug audio equipment into
these connections.

8 \
Functions
Functions and Descriptions:
1- Power: Plug the provided AC power cord here, make sure to connect the cord to the smart light show first and then to
an AC wall power outlet.
2- Display: This screen shows various menu selections
3- Mic: Internal microphone to detect sound for sound activation modes
4- Menu: Press to cycle through the 8 light modes
1. Pu- UV light
2. LA- Laser effect
3. LE- Moonflower LED effect
4. FL- Strobe light effect
5. PA- Water Ripple effect
6. AU- Automatic setting
7. S- Sound Activated
8. A- DMX Channel
5- Arrows: Use to select the various settings in each light mode
6- Enter: Press to change the speed of the selected light setting. This option only works with Laser, Moonflower, and
Water Ripple effects.
1
3
4
5
6
2

/ 9
Remote Control
Remote Functions:
Power- press to disable lights and enter stand-by mode
Auto- press to enter auto mode
Sound- press to directly access the sound activated modes
LED- press to directly access the Moonflower or Water Wave effect
mode, hold to switch between the two modes
LS- press to directly access the laser modes
UV- press to directly access the UV/Black light effect
Flash- press to directly access the strobe light setting
The remote functions – MOTOR,SPEED, and SEN –can only work within certain modes:
MOTOR: Only works when the remote control is in the LED moonflower mode. Press “+” to increase the rate
at which the motor is rotating.
SPEED: Only works when the remote control is in Flash mode (strobe light effect). Press “+” to speed up the pulse rate
of the light or “–” to decrease the pulse rate.
SEN: Only works when the remote control is in Sound mode and will increase or decrease the microphone sensitivity.

10 \
Menu Functions
1. Pu- UV Control
PUON- UV on under LA LE FL mode
PUOF- UV off under LA LE FL mode
2. LA- Laser Control
LAoF- Laser off
LAAu-Laser on auto
LAr- Red laser on
LA G- Green laser on
LArG- Red and green laser on
LA01-LA20- Laser on auto. The higher the number, the faster it runs
SP 1-9- Laser and strobe both on. The bigger the number the faster it runs (Need to push enter to adjust)
3. LE- Moonflower LED Control
LE-1- Red LED on
LE-2- Green LED on
LE-3- Blue LED on
LE-4- Red green blue random
LE-5- Mix color random
LE-6- Mix color flash
LE-7- Auto repeat LE-4 to LE-6
Sd 1-9 -Flash speed control LE-4 to LE-7 (need to push enter They go to the number the faster it flashes )
SP 1-9 -Motor speed control (need to push enter to control. Bigger the number the faster it goes)
4. FL- Strobe Mode Control
FLoF -Strobe OFF
FL 1-9 -Strobe speed, the bigger the number the slower it strobes
5. PA- Water Effect LED Control
PA-1- Red water effect LED on
PA-2- Green water effect LED on
PA-3- Blue water effect LED on
PA-4- White water effect LED on
PA-5- Single color Random water effect LED on
PA-6- Mixed colored Random water effect LED on
PA-7- Flash water effect LED
PA-8- Auto repeat PA 5 to PA 6
Sd 1-9 Flash speed repeat PA 4 to PA 8 ( Press enter to adjust speed )
SP 1-9 Motor and flash speed control ( Press enter to adjust speed )
6. AU 1- Auto Mode 1
AU 2- Auto Mode 2
-Continues on page 11

/ 11
Menu Functions Continued and DMX
7. S1- Sound Activation
S101-S120- Sound activation mode 1 (the two digit in the back are the calculation of the beat of music).
VoL1-VoL9- Sensitivity for sound activation mode (press up and down to enter the bigger the number the
more sensitive)
S2- Sound Activation
S101-S120- Sound activation mode 2 (the two digit in the back are the calculation of the beat of music).
VoL1-VoL9-Sensitivity for sound activation mode (press up and down to enter the bigger the number the
more sensitive).
8. A001-A512- DMX Mode
Channel Value Function
10-9
10-255
WATER WAVE FX OFF
WATER WAVE FX SINGLE COLOR
20-9
10-255
WHITE LED OFF
WHITE LED ON
30-9
10-44
45-79
80-114
115-149
150-184
185-219
220-255
MOONFLOWER LED OFF
MOONFLOWER LED RED ON
MOONFLOWER LED GREEN ON
MOONFLOWER LED BLUE ON
MOONFLOWER LED RED + GREEN ON
MOONFLOWER LED GREEN+ BLUE ON
MOONFLOWER LED RED + BLUE ON
MOONFLOWER LED RED+ BLUE+ GREEN ON
40-9
10-99
100-199
200-255
LASER OFF
LASER RED ON
LASER GREEN ON
LASER RED + GREEN ON
50-9
10-255
UV OFF
UV ON
60-255 CONTROL CHANNELS 1-5
70-9
10-255
WATER WAVE EFFECT LED OFF
WATER WAVE EFFECT LED ON
80-9 WATER WAVE EFFECT LED MOTOR OFF
WATER WAVE EFFECT MOTOR CONTROL
90-9
10-255
MOONFLOWER MOTOR OFF
MOONFLOWER MOTOR SPEED
10 0-9
10-127
128-255
LASER MOTOR OFF
LASER MOTOR CLOCKWISE SPEED
LASER MOTOR COUNTERCLOCKWISE SPEED
11 0-50
51-150
151-200
201-250
251-255
ALL 8 CHANNELS ON
AUTO 1
AUTO 2
SOUND ACTIVE 1
SOUND ACTIVE 2

Our Team is Here to Help
Please do not return to the retailer if you are having
a technical issue operating or connecting the unit. If
you need additional help, have questions, or need
support with your VocoPro product contact us:
Toll Free: 800-678-5348
TEL: [phone]
FAX: [phone]
Email Tech Support at:
[email protected]
DJ-Smart-LightShow Owner’s Manual
© VocoPro 2019
v1.0506
www.vocopro.com