VuPoint VuCam User manual

USER’S MANUAL

Lamp Base Type
Output Voltage
Input Voltage
Lighting Control
Bluetooth®
Light bulb
Dimensions (L x W x H)
Operating Temperature
Socket type E26
DC: 5V/1A
120VAC, 60Hz
On/Off/Light Scheduling
BLE Mesh Network
Bluetooth® BLE 4.0
Support maximum 40W, A15/A19 size
Incandescent, CFL or LED light bulb
Recommended LED light bulb
(not included)
2.4" x 2.0" x 2.5"
-4°F - 113°F
Camera
Video resolution
Field of View
Wi-Fi®
Bluetooth®
Siren Alarm
Lighting Control
Weatherproof Design
Dimensions (L x W x H)
Microphone
Speaker
Input Voltage
Compatibility
Operating Temperature
HD 1080p resolution
1920x1080 at 30 fps. H.264
180 degrees (diagonal)
2.4GHz & 5GHz 802.11 b/g/n/ac
Bluetooth® BLE 4.0
100 dB
On/Off/Light Scheduling
Yes
2.4" x 2.4" x 5.9"
Built-in
Built-in
DC: 5V/1A
iOS: 8 or above /
Android : 4.3 or above
-4°F - 113°F
VUcam
VUcam
Smart Socket
Adapter
Smart Socket
Adapter
Cable Clips for
1m Cable x 6
Cable Clips for
3m Cable x 6
Kit Components
Bracket Conduit
Power Extension
Cable (3m)
Power Cable (1m)
Mount Screws x 2 Anchors x 2 AC/ DC Adapter Allen Wrench
01 02

VUcamwith
SmartSocketAdapter
InstallationGuide
Smart Socket Adapter for use in dry or damp locations
Power Connection Options
Compatible light bulb types Compatible light fixtures
Compatible light fixtures
For use only with max. 40W, E26
and standard A15 / A19 size
Incandesent, CFL or LED light bulb.
Ceiling lamp and
Wall mounted lamp.
Light fixtures with motion sensor
or 12-hour mechanical timer.
Halogen, Candelabra, Triple Twin Tube,
Two Prong, Globe, Motion-activated
Light and others.
Compatible light bulb types
NOT Compatible light fixturesNOT Compatible light bulb types
04
VUcam Model No.: OC100KU
Smart Socket Adapter Model No.: SA010KU

For another light fixture, please make
additional purchase on second Smart
Socket Adapter and install it for light
synchronization.
Smart Socket Adapter Installation
Remove cover and insert Power Cable to Smart Socket Adapter.
Install Smart Socket Adapter to fixture, and thread in light bulb.
Disassemble the lamp sconce if necessary.
Upward
Installation
Downward
installation
Before installation, ensure the power switch is OFF or disconnect power at the fuse.
Drag out Power Cable through the shade and then adjust silicon sleeve
from Power Cable to protect the cable.
Screw lamp sconce or lamp cover back to your light fixture.
Use Cable Clips to manage the cable if necessary.
05 06

Remove back cover from the bottom of the camera, insert
Power Cable, and then coil the cable around wrapping posts.
Vertical line Horizontal line
Mounting the Camera
After using the Leveler to adjust the balance of the Bracket,
mount it with Anchors and Screws.
Alternative power source
Connect camera directly to alternative power
outlet with Extension Power Cable. Use Cable
clips to manage the cable if necessary.
Power
Cable
Power
Cable
Power
Extension
Cable
For camera installation with light fixture
above the door (optional)
Use Power Extension Cable to connect
Power Cable from camera with ceiling light
fixture above the door. Use Cable clips to
manage the cable if necessary. Reinstall the back cover to the camera.
07 08
Power
Extension
Cable
AC / DC
Adapter

Attach the camera to the Bracket and slightly pull camera down
to snap the camera in place.
Align Power Cable and extend the Conduit to preferred length.
Secure conduit onto the wall.
Adjust the camera to your desired position and angle.
Tighten the security
screws on both sides
by using the supplied
Allen Wrench.
Adjust the lens vertically with
fingers to your desired position.
Do not over-tighten the security screws.
Manage the cable with optional Conduit. Remove the adhesives from the Conduit,
then slide the bottom of the Conduit into the Bracket.
09 10

Companion
withMobile
InstallationGuide
2. Open VUpoint Home app
Tap the app icon to launch application.
1. Download "VUpoint Home" app
Scan the QR code or search “VUpoint
Home” on google play or app store to
download the app.
6. Connect wifi
Enter your wifi password then tap "Next".
5. Camera found
Once camera device is found,
tap "Next" to continue setup.
3. Add camera
On the homepage, tap the add
camera icon in the upper right corner.
4. Before set up
Follow on-screen instructions to
proceed with installation.
12

7. Camera added
After camera added, tap "Add other device"
to pair camera with companion devices.
8. Adding Smart Socket Adapter
From New Device page, tap to select
Smart Socket Adapter to pair.
10. Complete
Device map illustrates which
devices are connected.
9. New device light on
Selected Smart Socket Adapter is light
on in app as well as on device.
Troubleshooting and FAQ
Note: Model Number and Serial Number (S/N) are located on the packaging, instruction
manual, or on the product. Please have this information ready before contacting tech support.
1.
2.
3.
How long will my recordings be available?
All VUcam units come standard with 24-hour event review and download. With
premium subscription plans, you can “go back in time” to access every event that
your VUcam generated.
How many VUcams can I install?
There’s no limit. We recommend installing VUcams at all major entry points. You can
add multiple cameras to your VUpoint Home app and manage each camera all in
one app.
I do not see any VUcam show up in setup screen.
VUcam uses Bluetooth® LE 4.0 for setup. You will need to be within a maximum
distance of 30 feet from VUcam devices and have Bluetooth enabled on your
mobile device. Try rebooting your mobile device and launch the VUpoint Home
app again when necessary.
Frequently Asked Questions
VUcam
TroubleshootingandFAQ
RegulationsandCompliance
Compatibility
Appendix
13 14

4.
5.
My VUcam is “Offline”.
1)
2)
How can I reset my camera?
VUcam can be reset through app, you can remove camera and re-add the camera in app
again. You can also reset the camera manually by pressing the reset button at back for 7
seconds until you see the flash light changes to red.
Reboot camera: Turn off your VUcam (using the light switch it’s connected to) and wait
at least 10 seconds. Then, turn on the light switch back on.
Run through the set-up process: Re-add the VUcam again.
This may be caused by weak Wi-Fi signal. Improve performance by moving your router
closer to your VUcam, or adding a Wi-Fi extender in between.
Do I have to leave my light switch on?
Yes, VUcam uses power continuously, so you will have to leave the light switch on. We
have provided with your VUcam a “Keep it on” label as reminder to leave the switch on.
Can I use LED bulb with Smart Socket Adapter?
Yes, we recommend that you use an LED bulb.
What is the maximum light bulb wattage I can use with the Smart Socket Adapter?
Smart Socket Adapter supports up to maximum 40W.
My Smart Socket Adapter is “Offline”.
VUcam uses BLE Mesh Network that is capable to provide connections for all devices within
30 feet. Firstly, ensure your Smart Socket Adapter is within this range with the camera. If your
device still looks offline in the device map of VUpoint Home app, please go through the reset
procedures once.
How can I reset my Smart Socket Adapter?
Smart Socket Adapter can be reset through app, you can remove Smart Socket Adapter
and re-add it in app again. Another reset method is to press the on/off button in a designed
sequence. When the light is on, press the light off for 3 seconds then on for 1 second. Repeat
this sequence for three times. After reset, the light bulb will flash for 3 times, please note the
light bulb will not light up once reset is successful.
Smart Socket Adapter
1.
2.
3.
4.
5.
Regulations and Compliance
IMPORTANT SAFETY INSTRUCTIONS
Please adhere to the following safety instructions. Failure to follow the instructions outlined in
the user’s manual may lead to serious personal injury and possible property damage.
SAVE THESE INSTRUCTIONS
Smart Socket Adapter DC power output max. up to 5W.
The Smart Socket Adapter must be installed in the listed lampholder.
Power Cable use only with the Camera Model: OK110KU.
Class 2 output connections are not intended for supporting products or appliances.
Use only the Power Cable packaged with the Camera Model: OK110KU. The Smart
Socket Adapter and Power Cable may become warm during normal use. Always
allow adequate ventilation around the Smart Socket Adapter and Power Cable and
use care when handing. Unplug the device if any of the following conditions exist:
• The Power Cable or Smart Socket Adapter has become frayed or damaged
• The Power Connector or Smart Socket Adapter is exposed to rain, liquid, or
excessive moisture
• The Power Cable or Smart Socket Adapter has become damaged
• You suspect the Power Cable or Smart Socket Adapter needs service or repair
• You want to clean the Power Cable or Smart Socket Adapter
• Class 2 output connections are not intended for supporting products
or appliances
Safety & Operations
15 16

FCC Statement
Warning: Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference
that may cause undesired operation.
The transmitter must not be co-located or operated in conjunction with any other antenna or
transmitter. This equipment complies with the FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with a minimum
distance of 20cm between the radiator and any part of your body.
(i) the device for operation in the band 5150–5250 MHz is only for indoor use to reduce
the potential for harmful interference to co-channel mobile satellite systems;
(ii) for devices with detachable antenna(s), the maximum antenna gain permitted for
devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment
still complies with the e.i.r.p. limit;
(iii) the worst case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask
requirement set forth in Section 6.2.2(3) shall be clearly indicated.
17 18
Until further notice, devices subject to this section shall not be capable of transmitting in the
band 5600-5650 MHz.This restriction is for the protection of Environment Canada’s weather
radars operating in this band.
OC100KU FCC ID: 2AK7ELIH01 SA010KU FCC ID: 2AK7ELIH03
IC Caution
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102
and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF
exposure and compliance.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter. This equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation estautorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareildoit accepter tout brouillageradioélectrique subi,
mêmesi le brouillage est susceptible d'en compromettre le fonctionnement.
Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de
RSS 102 etla conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information
canadienne surl'exposition et la conformité de rf.
Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune
autre antenne ouémetteur. Cet équipement devrait être installé et actionné avec une
distance minimum de 20 centimètres entre le radiateur et votre corps.
OC100KU IC: 22430-LIH01 SA010KU IC: 22430-LIH03

Compatibility
For a compatible list of light bulbs and light fixtures,
visit: www.vupointhome.com/compatibility
Socket for use in dry or damp locations. Support up to max. 40W, E26 and
standard A15 / A19 size incandesent, CFL or LED light bulb.
Socket requires continuous power from light fixtures.
Not compatible to motion-activated light fixtures and power timer.
App Store is a service mark of Apple Inc., in the U.S. and other countries. Google Play badge is
a trademark of Google, Inc. Use of this trademark is subject to Google Permission.
Product names, logos, brands, and other trademarks, referred to herein are the property of
their respective trademark holders. All trademarks remain the property of their respective
holders, and are used only to directly describe the products being provided. These trademark
holders are not affiliated with VuPoint Solutions Inc. They do not sponsor or endorse VuPoint
Solutions Inc. products or services.
VUcam_US Manual_17-0310
vupointhome.com