WAGO 750-626 User manual

Fieldbus Independent
I/O Modules
24 V DC Power Supply Filter with
Overvoltage (Surge) Protection
750-626
Manual
Version 1.0.2

ii • General
WAGO-I/O-SYSTEM 750
I/O Modules
Copyright ©2006 by WAGO Kontakttechnik GmbH & Co. KG
All rights reserved.
WAGO Kontakttechnik GmbH & Co. KG
Hansastraße 27
D-32423 Minden
Phone: [phone] – 0
Fax: [phone] – 1 69
E-Mail: [email protected]
Web: http://www.wago.com
Technical Support
Phone: [phone] – 5 55
Fax: [phone] – 85 55
E-Mail: [email protected]
Every conceivable measure has been taken to ensure the correctness and com-
pleteness of this documentation. However, as errors can never be fully ex-
cluded, we would appreciate any information or ideas at any time.
E-Mail: [email protected]
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally trademark or patent protected.

Content •iii
WAGO-I/O-SYSTEM 750
I/O Modules
CONTENT
1Important Comments ................................................................................. 4
1.1 Legal Principles........................................................................................4
1.1.1 Copyright............................................................................................. 4
1.1.2 Personnel Qualification .......................................................................4
1.1.3 Intended Use ........................................................................................4
1.2 Symbols....................................................................................................5
1.3 Number Notation......................................................................................5
1.4 Safety Notes .............................................................................................6
1.5 Scope ........................................................................................................6
2I/O Modules ................................................................................................. 7
2.1 System Modules .......................................................................................7
2.1.1 750-626 [24 V DC Power Supply Filter with Overvoltage (Surge)
Protection] ...........................................................................................7
2.1.1.1 View................................................................................................7
2.1.1.2 Description......................................................................................7
2.1.1.3 Display Elements ............................................................................8
2.1.1.4 Schematic Diagram.........................................................................8
2.1.1.5 Technical Data ................................................................................9
2.1.1.6 Power supply concept ...................................................................10

4 •Important Comments
Legal Principles
WAGO-I/O-SYSTEM 750
I/O Modules
1 Important Comments
To ensure fast installation and start-up of the units described in this manual,
we strongly recommend that the following information and explanations are
carefully read and abided by.
1.1 Legal Principles
1.1.1 Copyright
This manual is copyrighted, together with all figures and illustrations
contained therein. Any use of this manual which infringes the copyright
provisions stipulated herein, is not permitted. Reproduction, translation and
electronic and photo-technical archiving and amendments require the written
consent of WAGO Kontakttechnik GmbH & Co. KG. Non-observance will
entail the right of claims for damages.
WAGO Kontakttechnik GmbH & Co. KG reserves the right to perform
modifications allowed by technical progress. In case of grant of a patent or
legal protection of utility patents all rights are reserved by WAGO
Kontakttechnik GmbH & Co. KG. Products of other manufacturers are always
named without referring to patent rights. The existence of such rights can
therefore not be ruled out.
1.1.2 Personnel Qualification
The use of the product detailed in this manual is exclusively geared to
specialists having qualifications in PLC programming, electrical specialists or
persons instructed by electrical specialists who are also familiar with the valid
standards. WAGO Kontakttechnik GmbH & Co. KG declines all liability
resulting from improper action and damage to WAGO products and third party
products due to non-observance of the information contained in this manual.
1.1.3 Intended Use
For each individual application, the components supplied are to work with a
dedicated hardware and software configuration. Modifications are only
permitted within the framework of the possibilities documented in the
manuals. All other changes to the hardware and/or software and the non-
conforming use of the components entail the exclusion of liability on part of
WAGO Kontakttechnik GmbH & Co. KG.
Please direct any requirements pertaining to a modified and/or new hardware
or software configuration directly to WAGO Kontakttechnik GmbH & Co.
KG.

Important Comments •5
Symbols
WAGO-I/O-SYSTEM 750
I/O Modules
1.2 Symbols
Danger
Always abide by this information to protect persons from injury.
Warning
Always abide by this information to prevent damage to the device.
Attention
Marginal conditions must always be observed to ensure smooth operation.
ESD (Electrostatic Discharge)
Warning of damage to the components by electrostatic discharge. Observe
the precautionary measure for handling components at risk.
Note
Routines or advice for efficient use of the device and software optimization.
More information
References on additional literature, manuals, data sheets and INTERNET
pages
1.3 Number Notation
Number Code Example Note
Decimal 100 normal notation
Hexadecimal 0x64 C notation
Binary '100'
'0110.0100'
Within ',
Nibble separated with dots

6 •Important Comments
Safety Notes
WAGO-I/O-SYSTEM 750
I/O Modules
1.4 Safety Notes
Warning
Switch off the system prior to working on bus modules!
In the event of deformed contacts, the module in question is to be replaced, as
its functionality can no longer be ensured on a long-term basis.
The components are not resistant against materials having seeping and
insulating properties. Belonging to this group of materials is: e.g. aerosols,
silicones, triglycerides (found in some hand creams).
If it cannot be ruled out that these materials appear in the component
environment, then additional measures are to be taken:
- installation of the components into an appropriate enclosure
- handling of the components only with clean tools and materials.
Attention
Cleaning of soiled contacts may only be done with ethyl alcohol and leather
cloths. Thereby, the ESD information is to be regarded.
Do not use any contact spray. The spray may impair the functioning of the
contact area.
The WAGO-I/O-SYSTEM 750 and its components are an open system. It
must only be assembled in housings, cabinets or in electrical operation
rooms. Access must only be given via a key or tool to authorized qualified
personnel.
The relevant valid and applicable standards and guidelines concerning the
installation of switch boxes are to be observed.
ESD (Electrostatic Discharge)
The modules are equipped with electronic components that may be destroyed
by electrostatic discharge. When handling the modules, ensure that the
environment (persons, workplace and packing) is well grounded. Avoid
touching conductive components, e.g. gold contacts.
1.5 Scope
This manual describes the System Module 750-626 24 V DC Power Supply
Filter with Overvoltage (Surge) Protection of the modular
WAGO-I/O-SYSTEM 750.
Handling, assembly and start-up are described in the manual of the Fieldbus
Coupler. Therefore this documentation is valid only in the connection with the
appropriate manual.

750-626 [24 V DC Power Supply Filter with Overvoltage (Surge) Protection] •7
View
WAGO-I/O-SYSTEM 750
I/O Modules
2 I/O Modules
2.1 System Modules
2.1.1 750-626 [24 V DC Power Supply Filter with Overvoltage (Surge)
Protection]
Filter Module, for system and field side power supply
2.1.1.1 View
++
-
13 14
C
D
B
A
750-626
+
+Ñ
-
-
0V
Data contacts
Power jumper contacts
Status
voltage supply
- Power jumper contacts
- System
Supply via power
jumper contacts
24V
System supply (out)
24 V
0V
System supply (in)
24 V
0V
Fig. 2.1.1-1: Filter Module 750-626 g062600e
2.1.1.2 Description
The overvoltage protection module 750-626 is used to supply a fieldbus node.
This module has a filter for the 24 V system power supply and is equipped
with surge suppression for both the system and field side power supply via
power jumper contacts.
The WAGO-I/O-SYSTEM 750 can also be used in shipping industry
applications. Suitable onshore and offshore installations are: platforms,
loading facilities, cranes, monitor systems for containers, and other onboard
systems. This is possible via certification under the standards of leading
agencies such as Germanischer Lloyd and Lloyd‘s Register. Proper system
operation is ensured (certified) by using this filter module.

8 • 750-626 [24 V DC Power Supply Filter with Overvoltage (Surge) Protection]
Display Elements
WAGO-I/O-SYSTEM 750
I/O Modules
Warning
The maximum current of the filter module is 10 A. When configuring the
system it is important not to exceed the maximum/sum current. However, if
such a case should occur, another supply module must be added.
The filter module 750-626 can be used with all couplers/controllers of the
WAGO-I/O-SYSTEM 750.
2.1.1.3 Display Elements
LED Designation State Function
off No DC 24 V system voltage
supply.
A
green
Status
voltage supply
–
System on DC 24 V system voltage supply.
off No DC 24 V voltage supply via
power jumper contacts.
Fig. 2.1.1-2: Display
Elements g062602x C
green
Status voltage
supply
–
Power jumper
contacts. on DC 24 V voltage supply via power
jumper contacts.
2.1.1.4 Schematic Diagram
750-626
1
2
3
4
5
6
7
8
24 V
0V
24 V
0V
24 V
0V
24 V
24 V
0V
24 V
0V
0V
Fig. 2.1.1-3: Filter Module 750-626 g062601e

750-626 [24 V DC Power Supply Filter with Overvoltage (Surge) Protection] •9
Technical Data
WAGO-I/O-SYSTEM 750
I/O Modules
2.1.1.5 Technical Data
Module Specific Data
Voltage via power jumper contacts max. DC 24 V (-25% ... +30%)
Current via power jumper contacts max. 10 A
Current via system voltage max. 1 A
Dimensions (mm) W x H x L 12 x 64* x 100
* from upper edge of 35 DIN rail
Weight ca. 50 g
Standards and Regulations (cf. Chapter 2.2 of the Coupler/Controller Manual)
EMC-Immunity to interference (CE) acc. to EN 50082-2 (1996)
EMC-Emission of interference (CE) acc. to EN 50081-1 (1993)
EMC-Immunity to interference (Ship building) acc. to Germanischer Lloyd (01)
EMC-Emission of interference (Ship building) acc. to Germanischer Lloyd (01)
Approvals (cf. Chapter 2.2 of the Coupler/Controller Manual)
CULUS (UL508)
ABS (American Bureau of Shipping) 1)
BV (Bureau Veritas) 1)
DNV (Det Norske Veritas) 1) Cl. B
GL (Germanischer Lloyd) 1) Cat. A, B, C, D
KR (Korean Register of Shipping) 1)
LR (Lloyd's Register) 1) Env. 1, 2, 3, 4
NKK (Nippon Kaiji Kyokai)
RINA (Registro Italiano Navale) 1)
Conformity Marking
1) Note information on “Voltage Supply“!
More Information
Detailed references to the approvals are listed in the document "Overview
Approvals WAGO-I/O-SYSTEM 750", which you can find on the CD ROM
ELECTRONICC Tools and Docs (Item-No.: 0888-0412)
or in the internet under:
www.wago.com !Documentation !WAGO-I/O-SYSTEM 750 !
System Description

10 • 750-626 [24 V DC Power Supply Filter with Overvoltage (Surge) Protection]
Power supply concept
WAGO-I/O-SYSTEM 750
I/O Modules
2.1.1.6 Power supply concept
The following illustration shows the power supply concept of a
WAGO-I/O-SYSTEM 750 fieldbus node for the certified application
according to GL / LR.
626 602 610 624 612
(601)
(610) 609
611(602)
(601)
~
24V 24V 24V 230V
Potential 1 Potential 2 Potential 3
Field Electronic Field Field
Field
I/O Modules
Fieldbus Coupler/
Controller
Endmodule
Fig. 2.1.1-1: Power supply concept g060203e
The 24 V system power supply of the coupler / controller must be filtered
using the filter module 750-626 and protected against overvoltages.
The 24 V field power supplies must be protected against overvoltage using the
filter modules 750-624 or 750-626.
When supplying the ground (earth) potential via the power jumper contacts or
if a fuse protection or monitoring of the field power supply is required, a
supply module 750-601 (24 V power supply with fuse), 750-602 (24 V power
supply without fuse) or 750-610 (24 V power supply with fuse and
diagnostics) should be used in addition to the filter module 750-626.
Otherwise the use of a supply module is not required in addition to the filter
module 750-626. The downstream modules can then be directly supplied via
the power jumper contacts of the filter module 750-626.
For each additional 24 V field side power supply, a filter module 750-624 is to
be used in addition to the supply module 750-601, 750-602 or 750-610.
No filter module is required using 230 V field side power supply.

750-626 [24 V DC Power Supply Filter with Overvoltage (Surge) Protection] •11
Power supply concept
WAGO-I/O-SYSTEM 750
I/O Modules

WAGO Kontakttechnik GmbH & Co. KG
Postfach 2880 • D-32385 Minden
Hansastraße 27 • D-32423 Minden
Phone: [phone] – 0
Fax: [phone] – 1 69
E-Mail: [email protected]
Internet: http://www.wago.com