WAGO 750 Series User manual

System manual | Version 3.3.1
WAGO I/O System 750/753
Decentralized Automation Technology
Serie 750, 753

Serie 750, 753Legal Information
© 2023 WAGO GmbH & Co. KG
All rights reserved.
WAGO GmbH & Co. KG
Hansastraße 27
D - 32423 Minden
Phone: [phone] – 0
Fax: [phone] – 844169
E-Mail: * [email protected]
Internet: ü www.wago.com
Technical Support
Phone: [phone] – 44555
Fax: [phone] – 844555
E-Mail: * [email protected]
Every conceivable measure has been taken to ensure the accuracy and completeness of
this documentation. However, as errors can never be fully excluded, we always appreci-
ate any information or suggestions for improving the documentation.
E-Mail: * [email protected]
We wish to point out that the software and hardware terms as well as the trademarks of
companies used and/or mentioned in the present manual are generally protected by
trademark or patent.
WAGO is a registered trademark of WAGO Verwaltungsgesellschaft mbH.
System manual | Version: 3.3.1

Serie 750, 753 Table of Contents
System manual | Version: 3.3.1 iii
Table of Contents
1Provisions ........................................................................................................................6
1.1 Validity of this Documentation .................................................................................6
1.2 Intended Use ...........................................................................................................6
1.3 Typographical Conventions .....................................................................................7
1.4 Legal Information.....................................................................................................9
2Safety ..............................................................................................................................10
2.1 General Safety Regulations...................................................................................10
2.2 Elektrische Sicherheit ............................................................................................10
2.3 Mechanical Safety .................................................................................................11
2.4 Thermal Safety ......................................................................................................11
2.5 Indirect Safety........................................................................................................11
3System Features ............................................................................................................12
3.1 Component Structure ............................................................................................12
3.1.1 Designs.........................................................................................................12
3.1.2 Structure of the Head Stations .....................................................................13
3.1.3 I/O Module Configuration .............................................................................15
3.1.4 Product Identification....................................................................................18
3.1.4.1 Versions ..............................................................................................18
3.1.4.2 Marking................................................................................................19
3.1.4.3 Identification ........................................................................................21
3.1.4.4 Update Matrix......................................................................................21
3.1.5 System Contacts ..........................................................................................21
3.1.5.1 Data Contacts......................................................................................21
3.1.5.2 Power Jumper Contacts......................................................................22
3.1.5.3 DIN-Rail Contact .................................................................................23
3.1.6 Coding Keys .................................................................................................23
3.1.7 Marking Elements.........................................................................................23
3.2 Electrical Structure ................................................................................................24
3.2.1 Potential Levels ............................................................................................24
3.2.2 System Supply..............................................................................................25
3.2.3 Field Supply..................................................................................................26
3.2.4 Power Supply Components..........................................................................26
4Functions........................................................................................................................28
4.1 Process Image.......................................................................................................28
5Planning..........................................................................................................................29
5.1 Node Structure ......................................................................................................29
5.2 Structure Guidelines ..............................................................................................30
5.2.1 Warning Messages for Structure Guidelines................................................30
5.2.2 Safety Measures at the Installation Location................................................30
5.2.3 Overcurrent Protection .................................................................................30
5.2.4 Protective Conductor and Protective Ground...............................................31
5.2.5 Buffering .......................................................................................................31

Serie 750, 753Table of Contents
iv System manual | Version: 3.3.1
5.2.6 Mounting Position and Clearances...............................................................31
5.2.7 DIN-Rail Characteristics ...............................................................................32
5.2.8 EMC Installations..........................................................................................33
5.2.9 Data Security................................................................................................33
5.3 Designing the System Supply................................................................................34
5.4 Field Supply Layout ...............................................................................................35
5.5 Special Applications and Environments ...............................................................35
5.5.1 Marine and Offshore.....................................................................................35
5.5.2 Exi Applications ...........................................................................................38
5.5.3 Marine and Offshore Exi Applications .........................................................39
5.5.4 Functional Safety..........................................................................................41
5.5.4.1 Power Supply Concept........................................................................41
5.6 Examples and Aids................................................................................................42
5.6.1 Aids...............................................................................................................42
5.6.2 I/O Test.........................................................................................................43
6Transport and Storage ..................................................................................................45
7Assembly and Disassembly .........................................................................................46
7.1 Warning Messages for Assembly and Disassembly..............................................46
7.2 Assembly Sequence..............................................................................................46
7.3 Snapping the Head Station to the DIN-Rail ...........................................................46
7.4 Attaching an I/O Module ........................................................................................47
7.5 Removing a Head Station from the DIN-Rail.........................................................48
7.6 Removing an I/O Module.......................................................................................49
7.7 Inserting Coding Keys ...........................................................................................51
8Conductor Termination .................................................................................................53
8.1 Conductor Termination ..........................................................................................53
8.1.1 Connecting Conductors to CAGE CLAMP®.................................................53
8.1.2 Connecting Conductors to Push-in CAGE CLAMP® ...................................54
9Decommissioning..........................................................................................................55
9.1 Shutting Down .......................................................................................................55
9.2 Disposal and Recycling .........................................................................................55
10 Appendix ........................................................................................................................56
10.1 Installation Regulations Specified by Approvals....................................................56
10.1.1 Special Notes Regarding Explosion Protection............................................56
10.1.2 UL Requirements from Installation Regulations ...........................................57
10.1.2.1 UL Ordinary Locations per Report Reference E175199-19970402 ....57
10.1.2.2 UL Ordinary Locations per Report Reference E175199-20180807 ....57
10.1.2.3 UL Ordinary Locations per Report Reference E175199-20181019 ....58
10.1.2.4 UL Ordinary Locations per Report Reference E175199-20210716 ....58
10.1.2.5 UL Ordinary Locations per Report Reference E175199-20230421 ....59
10.1.2.6 UL Hazardous Locations per Report Reference E198726-19980911
............................................................................................................59
10.1.2.7 UL Hazardous Locations per Report Reference E198726-2023-01-31
............................................................................................................61

Serie 750, 753 Table of Contents
System manual | Version: 3.3.1 v
10.2 Protected Rights ....................................................................................................61
10.3 Accessories ...........................................................................................................62

Serie 750, 753Provisions
6 System manual | Version: 3.3.1
1Provisions
1.1 Validity of this Documentation
This document applies to the I/O system:
WAGO I/O System 750/753 (Series 750, 753).
The complete operating instructions for the I/O system consists of several, applicable
documents. The I/O system must only be installed and operated in accordance with the
complete operating instructions. Knowledge of all applicable documents is required for
proper use. Please find all documents and information on the product detail pages.
Please find all documents and information at:
üwww.wago.com/all_750_753
Applicable documents
& Product manuals of used products
1.2 Intended Use
The I/O system is used to receive digital and analog signals from sensors and to control
actuators. Higher-level controllers can be communicated with through fieldbus interfaces.
The signals can be (pre-)processed with the controllers.
The products are open type devices and are designed for installation in an additional en-
closure. In order to use them, it is connect to take protective measures suitable for the
specific application.
• The products are intended for installation in automation technology systems.
• The products are designed for use in dry indoor rooms.
• Operation of the products in industrial areas is permitted.
• The products meet the EMC requirements for the residential, office and commercial
area as well as small business, if the products used complie with the required emis-
sions of interference (emission limits).
• Operation of the products in other application areas is only permitted when corre-
sponding approvals and labeling are present.
Improper Use
Improper use of the products is not permitted. Specifically, improper use occurs in the fol-
lowing cases:
• Non-observance of the intended use
• Use without protective measures in an environment in which moisture, salt water, salt
spray mist, dust, corrosive fumes, gases, direct sunlight or ionizing radiation can occur
• Use of the products in areas with special risk that require continuous fault-free opera-
tion and in which failure or operation of the product can result in an imminent risk to
life, limb or health or cause serious damage to property or the environment (such as
the operation of nuclear power plants, weapon systems , aircraft and motor vehicles)

Serie 750, 753 Provisions
System manual | Version: 3.3.1 7
Warranty and Liability
The provisions of the latest WAGO General Terms and Conditions of Deliveries and Ser-
vices (GTC) apply as well as the Software License Terms for Standard Software (SW-Li-
cense) applicable to software products und software embedded in WAGO hardware prod-
ucts, both available at: üwww.wago.com.
In particular, the warranty is void if:
• The products are used improperly.
• The deficiency (hardware and software configurations) is due to special instructions.
• Modifications to the hardware or software have been made by the user or third parties
that are not described in this documentation and that has contributed to the fault.
Individual agreements always have priority.
Obligations of Installers/Operators
The installers and operators bear responsibility for the safety of an installation or a sys-
tem assembled with the products. The installer/operator is responsible for proper con-
struction and safety of the installation. All laws, standards, guidelines, local regulations
and accepted technology standards and practices applicable at the time of installation,
and the instructions in the the products’ Instructions for Use, must be complied with. In
addition, the installment requirements for licensing must be observed. In the event of non-
compliance, the products may not be operated within the scope of the approval.
1.3 Typographical Conventions
Number Notation
100 Decimals: Normal notation
0x64 Hexadecimals: C-notation
‘100’
‘0110.0100’
Binary: In single quotation marks
Nibbles separated by a period
Text Formatting
italic Names of paths or files
bold Menu items, entry or selection fields, emphasis
Code Sections of program code
> Selection of a menu point from a menu
“Value” Value entries
[F5] Identification of buttons or keys
Cross References / Links
Cross references/links to a topic in a document
Cross references / links to a separate document
ü
Cross references / links to a website
Cross references / links to an email address

Serie 750, 753Provisions
8 System manual | Version: 3.3.1
Sequence of Action
üThis symbol identifies a precondition.
1. Action step
2. Action step
ðThis symbol identifies an intermediate result.
ðThis symbol identifies the result of an action.
• Individual action step
Lists
• Lists, first level
– Lists, second level
Figures
Figures in this documentation are for better understanding and may differ from the actual
product design.
Warning Messages
DANGER
Type and source of hazard
Indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury.
• Action step to reduce risk
WARNING
Type and source of hazard
Indicates a potentially hazardous situation which, if not avoided, could result in death or
serious injury.
• Action step to reduce risk
CAUTION
Type and source of hazard
Indicates a potentially hazardous situation which, if not avoided, may result in minor or
moderate injury.
• Action step to reduce risk

Serie 750, 753 Provisions
System manual | Version: 3.3.1 9
!
NOTICE
Type and source of malfunction (property damage only)
Indicates a potentially hazardous situation which, if not avoided, may result in damage to
property.
• Action step to reduce risk
Information Notices
Note
Information
Indicates information, clarifications, recommendations, referrals, etc.
1.4 Legal Information
Intellectual property
The intellectual property of this document belongs to WAGO GmbH & Co. KG. The repro-
duction and distribution of its content (in whole or in part) is prohibited, unless otherwise
provided by statutory provisions, written agreements or this document. In case of doubt,
the written consent of WAGO GmbH & Co. KG must be obtained in advance.
Third-party products are always mentioned without any reference to patent rights. WAGO
GmbH & Co.KG, or the manufacturer of third-party products, retains all rights regarding
patent, utility model or design registration.
Third-party trademarks are referred to in the product documentation. The “®” and “TM”
symbols are omitted hereinafter. The trademarks are listed in the Appendix: 8Protected
Rights [}61].
Subject to Change
The instructions, guidelines, standards, etc., in this manual correspond to state of the art
at the time the documentation was created and are not subject to updating service. The
installer and operator bear sole responsibility to ensure they are complied with in their
currently applicable form. WAGO GmbH & Co. KG retains the right to carry out technical
changes and improvements of the products and the data, specifications and illustrations
of this manual. All claims for change or improvement of products that have already been
delivered – excepting change or improvement performed under guarantee agreement –
are excluded.
Licenses
The products may contain open-source software. The requisite license information is
saved in the products. This information is also available under: üwww.wago.com.

Serie 750, 753Safety
10 System manual | Version: 3.3.1
2Safety
This section lists installation regulations that must be observed for safe operation of the I/O
System.
2.1 General Safety Regulations
• This documentation is part of the Products. Retain the documentation for the entire
service life of the Products. Pass on the documentation to any subsequent user of the
Products. In addition, ensure that any supplement to this documentation is included, if
necessary.
• The Products must only be installed and put into operation by qualified electrical spe-
cialists per EN 50110-1/-2 and IEC 60364.
• Comply with the laws, standards, guidelines, local regulations and accepted technol-
ogy standards and practices applicable at the time of installation.
2.2 Elektrische Sicherheit
• Disconnect all power supplies from the product before performing any installation, re-
pair or maintenance.
• Make sure the products do not carry any voltage before starting work.
Power Supply
• For non-hazardous active voltage per EN/UL/IEC 61010-1, SELV/PELV power sup-
plies shall be used.
• When configuring the system, make sure that the maximum total current of the field
supply of the node is not exceeded. Where needed, include an additional supply mod-
ule.
• When configuring the system, make sure that the maximum total current of the system
supply of the node is not exceeded. Where needed, include an additional supply mod-
ule.
• Pay attention to the permissible voltage and frequency ranges of the products when
using different supplies.
• Plan for voltage buffering if the requirement for voltage buffering according to EN
61131-2 is to be met.
• Take suitable measures to protect against overload (e.g., a supply module with fuse or
an external fuse).
• In mixed operation, always separate the areas in the XTR version and the areas with
the standard version with the separate potential supply modules for the field supply
and separate power supply units of the respective version in different potential groups.
Do not mix the versions within a potential group.
Grounding/Protection/Fuses
• Establish sufficient grounding. Make sure there is a flawless electrical connection be-
tween the DIN-rail and frame / additional enclosure.
• Connect the DIN-rail to protective ground (PE) when using hazardous active voltages.

Serie 750, 753 Safety
System manual | Version: 3.3.1 11
• In systems operated within the scope of UL, only use UL-approved fuses.
Cables
• To minimize interference (e.g., by electromagnetic interference), maintain a spatial
separation between control, signal and data lines and the power supply lines.
• SELV/PELV circuits must be safely disconnected from circuits with hazardous active
voltage or all connecting cables must be designed for the maximum current load.
• The conductor cross-sections specified in the product manual refer exclusively to the
mechanical connection capacity of the clamping points. Always use connecting cables
designed for the maximum current load.
• Additional heat can be produced at the clamping point by high currents and inherent
heat generated by the product. Plan a higher tenmperature range for the conductors,
or reduce inherent heat by selecting larger conductor cross-sections.
• Only one conductor may be connected to each connection point (e.g., CAGE CLAMP®
connection).
Protection
• When working on the system (e.g., during maintenance), protect the facility part in
question from accidental or unauthorized restart.
2.3 Mechanical Safety
• Before start-up, check the product for any damage that may have occurred during ship-
ping. Do not put the product into operation if there is any mechanical damage.
• Do not open the product housing.
• Do not touch the power jumper contacts.
• Avoid conductive contamination.
2.4 Thermal Safety
• The temperature inside the additional enclosure must not exceed the surrounding air
temperature permitted for the mounted products.
2.5 Indirect Safety
• Do not use any contact spray for cleaning.
• Clean product housings and soiled contacts with propanol.
• The products are not resistant to materials having seeping and insulating properties
such as aerosols, silicones and triglycerides (found in some hand creams). If these
substances occur in the environment of the products, install the products in an addi-
tional housing that is also resistant to these substances.
• Replace any defective or damaged devices.
• Do not place products on the data or power jumper contacts.
• If product fails, communication to downstream products may be interrupted.
• Products from the WAGO I/O System 750/753 can be operated in combination with
those of the WAGO I/O System 750 XTR. For combined operation, take the specifica-
tions for the ambient conditions for both I/O Systems into account.
• Operate ETHERNET and PROFINET interfaces in separate networks.
• Only use accessories authorized by WAGO.

Serie 750, 753System Features
12 System manual | Version: 3.3.1
3System Features
3.1 Component Structure
3.1.1 Designs
Head Stations
Figure1: Example Head Station Housings
The housings of head stations (fieldbus couplers or controllers) may differ, for instance in
terms of:
• The connection level with or without field-side power supply (Eco)
• The operator control elements and indicators
• The specific fieldbus interfaces
• Further communication interfaces
I/O Modules
Figure2: Example I/O Module Housings
The housings of the I/O modules differ in terms of:
The housings of the I/O modules may differ, for instance in terms of:
• The module width (12mm, 24mm or 48mm)
• The structure of the wiring interface (CAGE CLAMP® or Push-in CAGE CLAMP® con-
nections)
• Different indicators
• The number of power jumper contacts
• The fuse holder (supply module)
• The protective cover (distance module)

Serie 750, 753 System Features
System manual | Version: 3.3.1 13
3.1.2 Structure of the Head Stations
Beispielansicht PFC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Figure3: Beispielansicht PFC
1 Reset button & Product Manual
2 Data contacts 8System Contacts [}21]
3 Display elements: Power supply status & Product Manual
4 Display elements: System status & Product Manual
5 Access to open the associated CAGE CLAMP® con-
nection
8Conductor Termination [}53]
6 CAGE CLAMP® connection for the power supply
connection
7 Memory card slow with protective flap & Product Manual
8 Power jumper contact (spring) 8System Contacts [}21]
9 Release tab 8Assembly and Disassembly [}46]
10 Service interface cover & Product Manual
11 Mode selector switch & Product Manual
12 Network connection & Product Manual
13 Item number 8Product Identification [}18]
14 DIN-rail locking cam 8Assembly and Disassembly [}46]
15 Serial interface (optional) & Product Manual
16 Slot for Mini-WSB (optional) 8Marking Elements [}23]
8Versions [}18]

Serie 750, 753System Features
14 System manual | Version: 3.3.1
Beispielansicht Feldbuskoppler/Controller
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Figure4: Beispielansicht Controller
1 Slot for Mini-WSB (optional) 8Marking Elements [}23]
8Versions [}18]
2 Data contacts 8System Contacts [}21]
3 Display elements: Power supply status & Product Manual
4 Display elements: Fieldbus status & Product Manual
5 Access to open the associated CAGE CLAMP® con-
nection
8Conductor Termination [}53]
6 CAGE CLAMP® connection for the power supply
connection
7 Item number 8Product Identification [}18]
8 Power jumper contact (spring) 8System Contacts [}21]
9 Release tab 8Assembly and Disassembly [}46]
10 Service interface cover & Product Manual
11 Fieldbus connection (optional) & Product Manual
12 Memory card slow with protective flap & Product Manual
13 DIN-rail locking cam 8Assembly and Disassembly [}46]
14 Address selection switch (optional) & Product Manual

Serie 750, 753 System Features
System manual | Version: 3.3.1 15
3.1.3 I/O Module Configuration
Example View of the 750 Series I/O Module (CAGE CLAMP® Connections)
1
2
23
4
5
6
7
8
9
Figure5: 750 Series I/O Module with CAGE CLAMP® Connections (Example)
1 Slot for Mini-WSB (optional) 8Marking Elements [}23]
8Versions [}18]
2 Data contacts 8System Contacts [}21]
3 Indicators & Product Manual
4 Access to open the associated CAGE CLAMP® con-
nection
8Conductor Termination [}53]
5 CAGE CLAMP® connection
6 Power jumper contact (spring) 8System Contacts [}21]
7 Release tab 8Assembly and Disassembly [}46]
8 Item number 8Product Identification [}18]
9 Power jumper contact (blade) 8System Contacts [}21]

Serie 750, 753System Features
16 System manual | Version: 3.3.1
Example View of the 750 Series I/O Module (Push-in CAGE CLAMP® Connections)
1
2
23
4
5
6
7
8
9
Figure6: 750 Series I/O Module with Push-in CAGE CLAMP® Connections (Example)
1 Slot for Mini-WSB (optional) 8Marking Elements [}23]
8Versions [}18]
2 Data contacts 8System Contacts [}21]
3 Indicators & Product Manual
4 Access to open the associated Push-in CAGE
CLAMP® connection
8Conductor Termination [}53]
5 Push-in CAGE CLAMP® connection
6 Power jumper contact (spring) 8System Contacts [}21]
7 Release tab 8Assembly and Disassembly [}46]
8 Power jumper contact (blade) 8System Contacts [}21]
9 Item number 8Product Identification [}18]

Serie 750, 753 System Features
System manual | Version: 3.3.1 17
Example View of the 753 Series I/O Module (Pluggable Connector)
1
2
23
4
5
6
7
8
9
10
11
12
13
Figure7: 753 Series I/O Module (Example)
1 Slot for Mini-WSB (optional) 8Marking Elements [}23]
8Versions [}18]
2 Data contacts 8System Contacts [}21]
3 Indicators & Product Manual
4 Access to open the associated CAGE CLAMP® con-
nection
8Conductor Termination [}53]
5 CAGE CLAMP® connection
6 Release tab for the pluggable connector 8Assembly and Disassembly [}46]
7 Power jumper contact (spring) 8System Contacts [}21]
8 Release tab for the I/O module 8Assembly and Disassembly [}46]
9 Fastening clip for cable ties
10 Test slot for the associated CAGE CLAMP® connec-
tion
11 Power jumper contact (blade) 8System Contacts [}21]
12 Coding key 8Assembly and Disassembly [}46]
13 Item number 8Product Identification [}18]

Serie 750, 753System Features
18 System manual | Version: 3.3.1
3.1.4 Product Identification
3.1.4.1 Versions
Color Coding for Identifying the Component Type
To get an overview of the different I/O components quickly and easily, they are color-
coded.
Table1: Color coding of Component Types
Housing Color Component Type
Light gray WAGO I/O System 750/753 (standard modules)
Blue Intrinsically safe modules (Ex i)
Signal yellow Modules for functional safety
Blue + signal yellow Intrinsically safe modules (Ex i) for functional safety
Dark gray WAGO I/O System 750 XTR
Blue + dark gray WAGO I/O System 750 XTR – intrinsically safe modules (Ex i)
Color Coding for Identifying Functionality
To allow you to get an overview of the component classes present in a node quickly and
easily, they are color-coded.
• Housings with up to four round indicators have permanently installed color-coded pull-
out labeling fields.
• I/O modules in the 8-channel housing can be color-coded by attaching marking ele-
ments (Mini-WSB) above the indicators.
• For housings with 16indicators, they are highlighted in color.
Table2: Color Coding of Component Classes
Coding Key Color Component Class
Green Analog inputs
Blue Analog outputs
Yellow Digital inputs
Red Digital outputs
Transparent Supply modules, function and technology modules

Serie 750, 753 System Features
System manual | Version: 3.3.1 19
3.1.4.2 Marking
1
2
3
4
5
6
7
8910
11
12 13 14 15
Table3: Explanation of the Marking Example
No. Content Description
1 WAGO logo and address WAGO GmbH & Co. KG
2 Product information Item number and product description; conductor
cross-section if applicable
3 Production data
4 DataMatrix code (production data)
5 Terminal allocation For more information on Sprungziel: Anhang, see
the corresponding & Product Manual.
6 CE mark With the CE mark, WAGO declares that the product
meets the applicable requirements as set out in
Community harmonization legislation per EC Regu-
lation 765/2008, which allows the product to carry
this mark.
7 “ESD” mark Note: Avoid electrostatic discharge!
The products are equipped with electronic compo-
nents that may be destroyed by electrostatic dis-
charge when touched. Please following the safety
precautions per DIN EN 61340-5-1/-3 to prevent
electrostatic discharge.
8 “Ex” registration icon The product meets the classified requirements ac-
cording to ATEX for operation in hazardous areas.
For more information on approvals, see the corre-
sponding & Product Manual.

Serie 750, 753System Features
20 System manual | Version: 3.3.1
No. Content Description
9 “Caution” exclamation icon Note: Observe the product documentation!
Applicable information and documents concerning
the product exist which must be observed.
10 “KC” registration icon This approval mark indicates compliance with Ko-
rean product safety requirements for electrical and
electronic devices and components.
11 “UL Listed” mark “Certification Mark for Safety” of UL-listed product in
the North America and Canadian market
12 “WEEE” mark Note: Electrical and electronic equipment must not
be disposed of with household waste!
Electrical and electronic equipment contains materi-
als and substances that can be harmful to the envi-
ronment and health. Electrical and electronic equip-
ment must be disposed of properly after use.
For more information on this topic, see 8Disposal
and Recycling [}55].
13 Production number 8Identification [}21]
14 “Marine approvals” icon Collective icon for marine approvals
For more information on this topic, see 8Special
Applications and Environments [}35].
For more information on the topic of approvals, see
the corresponding & Product Manual.
15 Update matrix 8Update Matrix [}21]
Table4: Explanation of the Example of Different Marking
No. Content Description
UKCA The UKCA (UK Conformity Assessed) mark de-
clares that the conformity requirements for the UK
market are met.
“RFID” icon This product contains RFID (Radio Frequency
Identification) technology.
“Hot surface” warning symbol Warning: Do not touch hot surfaces!
The housing surface can become hot during oper-
ation. If the product has been used in high ambient
temperatures, let it cool down before touching it.
“TÜV” registration icon TÜV (Technischer Überwachungsverein) Rhein-
land® as the testing laboratory for functional safety
“FS” registration icon Conformity marks with the keyword “Functional
Safety” are issued for electrical/electronic/program-
mable electronic and electromechanical products
that are intended for use in safety-related applica-
tions.
“RCM” mark With the RCM mark (Regulatory Compliance
Mark), WAGO declares that the product meets the
applicable requirements according to Australian
standards.
“CCC” mark With the CCC (China Compulsory Certification)
mark, WAGO declares that the product meets the
applicable requirements according to standards
valid for the Chinese market.