Wali GSDM001-P User manual

[email protected]
75x75/100x100 35"
MAX
2-12kg
(4.4-26.
4lbs)
RATED
GSDM001-P
INSTALLATION MANUAL
Single Monitor Desk Mount

2

A (x1)
VESA Plate
B (x1)
Pole
C (x1) D (x1)
E (x1) F (x1) G (x1)
Bolt
H (x1)
I (x1) J (x1) K (x1)
Spring Washer
L (x1)
M6X16 Bolt
M (x3)
M6X12 Bolt
N (x3)
M6X10 Bolt
O (x2)
M5X12 Bolt
M-B (x4)
D5 Washer
M-C (x4)
P (x4)
Wire Clip
Q (x1)
4mm Allen Key
R (x1)
6mm Allen Key
S (x1)
Wrench
T (x1)
Base
C-Clamp
Cover
Grommet Base Plate Nut
Anti-skid Pad
M4X12 Bolt
M-A (x4)
Support Plate
Supplied Parts List
3
Arm
C-clamp Brace

R
N
E
R
P
4
Step 2
Fit clamp: 0.4”-3.3”
Grommet: 0.4”-3.3“
Step 1
Option A
D
D
Clamp Installation
1. Connect Pole and Base from the bottom using M6X16 Bolt and tighten with 4mm Allen Key .
D
E
C
C
M
R
2. Connect Base and C-clamp Brace using M6x12 Bolt and tighten with 4mm Allen Key . Tear off the
protective paper to attach Anti-Skid Pad to the bottom designated position of Base as image shown.
DENR
PD
R
M
M
D

RO
or
G
O
5
4. Rotate the hand knob clockwise to fasten for stability. Attach the Cover to the C-Clamp.
G
FO
R
3. Select the preferred height firstly and connect C-Clamp to C-Clamp Brace using M6x10 Bolt and tighten
with 4mm Allen Key
.E
2’’-3.3’’
0.4’’-2.2’’
R
Hand Knob
F
F
F
F
EE

Option B
Grommet Base Installation
I
H
N
R
P
0.4’’-3.3’’
0.4’’-3.3’’
ø 10mm
(ø ")3/8
D
N
R
If the existing grommet hole comes with a plastic
protector, remove it to ensure a flat surface before
installing the desk mount.
P
D
2. Tear off the protective paper to attach Anti-Skid Pad to the
bottom designated position of Base as image shown.
1.Guide Grommet Base Plate through Bolt
and connect them to Base from the bottom
using M6x12 Bolt and tighten with 4mm Allen
Key . I
IH
D
6
3a.Existing Grommet Hole Installation 3b.Self-drilled Grommet Hole Installation
Mark the position of the hole on your mounting surface. Drill
a 3/8"(10mm) diameter hole at the marked position through
the mounting surface.
D

S
Q
A
Step 3
T
K
L
J
Put the Arm and Wire Clip through the Pole , adjust the preferred height and tighten using 6mm Allen Key .
AQCS
H
J
L
K
K
4. Insert the assembled pole through the desk hole, guide the Support Plate , Washer and Nut through the
Bolt , rotate the Nut clockwise to fasten for stability.
7

A
Select M4x12 Bolt or M5x12 Bolt according
to your TV/Monitor,connect VESA Plate together
with D5 Washer
into the mounting holes on the
back of TV/Monitor, tighten with screwdriver.
(Screwdriver needed but not included)
M-A M-B
B
M-C
BM-A
M-B
M-C
M-C
8
Step 4
Step 5
Step 4.1
M4 M5
Only one screw size fits your Monitor
Hand thread screws into the
threaded inserts on the back
of your Monitor to determine
which screw (M4or M5) to
use.
Step 4.2
Select Monitor Screws
Step 4.1
Step 4.2
Pull the buckle and put the assembled TV/Monitor onto the Arm and ensure stability.

S
9
Step 6
To properly balance the arm with monitors mounted, adjust the spring tension with 6mm Allen Key .
First, position and firmly hold the arm horizontally as
shown. Ask for assistance should you require it. If the arm drops, turn the adjustment screw
counter-clockwise until it stays in a horizontal
position.
To avoid damage to monitors or mount,
always keep the arm in a horizontal
position while making adjustments.
Again, ask for assistance if required.
If the arm rises, turn the adjustment screw
clockwise until it stays in a horizontal
position.
DO NOT over tighten the screws.

10
Step 7
Guide the cable through the cable slot.

Tilt: Adjust the VESA Plate tilt using
6mm Allen Key . (Tilt: +45°/-45°)
S
Note: Adjust to the desired
angle then tighten the screws
using the Allen key as shown,
alternating from each screw
as you tighten them.
S
Swivel : Manually adjust swivel angle. (Swivel:-90°/+90°) Rotate: Manually adjust rotate angle. (Rotate:180°)
11
Step 8 Angle Adjustments

1-844-SATTLER (18447288537) [email protected]
If you have any questions,please contact us.
 
We support the technology that brings your home to life.
We offer high quality products, professional customer service,
and extensive technical support.
www.walielectric.com