Wali M002XLS User manual

M002XLS
WARNING
！
！
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIP OVER.
SMALL PARTS- NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual.
Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect
assembly or inappropriate use.
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
Dual Monitor Desk Mount
INSTALLATION MANUAL
1-844-SATTLER (18447288537)
[email protected]
www.walielectric.com
TIPOVER WARNING
● NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
● USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL.
Supplied Parts List
Nut
E (x2) K (x2)
Wire Clip
Allen Key
I (x1)
M4x30 Bolt
G (x8)
M4x12 Bolt
F (x8) H (x8)
M4~M6 SpacerVESA Plate
D (x2)
C-Clamp
B1 (x1)
C-Clamp Brace
B2 (x1)
Grommet Base Plate
B5 (x1)
M10 Hand Knob
B4 (x1)
B3 (x1)
Support Plate
Lower Pole
A1 (x1)
Upper Pole
A2 (x1)
M5x14 Bolt
J1 (x3)
Monitor Arm
C (x2)
M8x12 Bolt
J2 (x2)
1
A2
A2
A1
A1
A1
I
I
Option A : 31.5'' Pole Installation
Loosen the screw on the Lower Pole a1 with Allen key 3mm o . Connect
Lower Pole a1 to Upper Pole and tighten the screw with Allen key
3mm o to fix the two poles.
A1
A1
Pre-Assembly
I
A2
I
Option A : Clamp Installation
1. Connect Lower Pole a and C-Clamp Brace c from the bottom using M5x14 Bolt f and tighten with Allen Key 3mm o .
2
Hand Knob
B2
A1
B2
J1
I
I
I
J1
B2
J2
B1
A1
B4
B3 B1
2. Remove the screw and washer at the top of the M10 Hand Knob and connect the M10 handle , C-clamp B1 and support plate with the screw
and washer that were just removed. Select the preferred height according to your desk thickness. Connect C-Clamp B1 to C-Clamp Brace B2 using M8x12
Bolt J1 , and tighten with Allen Key 5mm I . Rotate the hand knob N clockwise to fasten for stability.
B4 B4 B1 B3
B2
B1
B4
I
J2

I
K
A2
3Put the Wire Clips k and Monitor Arms c through the Upper Pole a , adjust the preferred
height and tighten using Allen Key 5mm o .
7Manually swivel, tilt, and rotate the monitor for the best viewing angle. 6Guide the cable through the Wire Clips and store the Allen Keys o in the Wire Clips k .
Adjust the tilt angle using Allen Key 5mm n .
KIK
I
C
C
K
45°
45°
45°
45°
A2
I
Select bolts and spacers (if needed) according to your TV/Monitor. Attach the VESA Plate to the Monitor and tighten with a screwdriver. (Screwdriver not included)
Step 4.1
Select Monitor Screws
Step 4.3a
Flat Back Monitor
Step 4.3b
Curved or Recessed Back Monitor
D
F
H
G
D
M4x12 M4x30
4
Only one screw size fits your Monitor
Step 4.2
Select Spacers( if needed )
Hand thread screws into the
threaded inserts on the back
of your Monitor to determine
which screw (M4x12 orM4x30)
to use.
5Put the assembled TV/Monitor onto the Monitor Arms d and tighten the VESA Plate e with
Nut h for stability.
I
I
K
CD
E
E
D
Notice: Please make sure the security nut is installed before you rotate the monitor.E
E
Option B : Grommet Base Installation
1. Place Lower Pole a onto Grommet Base Plate m . Connect them from the bottom using M5x14
Bolt J1 and tighten with Allen Key 3mm .
I
J1
A1 B5
I
A1
B5
J1
Remove the screw and washer at the top of the M10 Hand Knob N .
If the existing grommet hole comes with a plastic protector, remove it to ensure a flat surface before
installing the desk mount.
Position the Pole A on the mounting surface and connect the hand knob N through the Support
Plate Q and the grommet hole with the Pole A . Rotate the hand knob N clockwise to fasten for
stability.
Remove the screw and washer at the top of the M10 Hand Knob N .
Mark the position of the hole on your mounting surface. Drill a 3/8"(10mm) diameter hole at the
marked position through the mounting surface.
Position the Pole A on the mounting surface and connect the hand knob N through the Support
Plate Q and the self-drilled hole with the Pole A . Rotate the hand knob N clockwise to fasten
for stability.
2a. Existing Grommet Hole Installation 2b. Self-drilled Grommet Hole Installation
A1
B3
B4
B4
B4
B4A1
A1
B3
B4 A1
A1
B4
B4
B4B3
A1
B3
B4
B4
C
ø 10mm
(ø ")3/8