Wali M12XXL User manual

M12XXL
WARNING
！
！
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIP OVER.
SMALL PARTS- NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual.
Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect
assembly or inappropriate use.
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
Dual Monitor Desk Mount
INSTALLATION MANUAL
1-844-SATTLER (18447288537)
[email protected]
www.walielectric.com
TIPOVER WARNING
● NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
● USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL.
Supplied Parts List
K (x2)
Wire ClipNut
E (x2)
M5x14 Bolt
J1 (x3)
M8x12 Bolt
J2 (x2)
Allen Key
I (x1)H (x8)
M4x30 Bolt
G (x8)
M4x12 Bolt
F (x8)
M4~M6 Spacer
VESA Plate
D (x2)
C-Clamp
B1 (x1)
C-Clamp Brace
B2 (x1)
Grommet Base Plate
B5 (x1)
B3 (x1)
M10 Hand Knob
B4 (x1)
Support Plate Swivel Arm
C (x2)
Wire Clip
L (x4)
Option A : Clamp Installation
1. Connect Lower Pole a and C-Clamp Brace c from the bottom using M5x14 Bolt f and tighten with Allen Key 3mm o .
2
Hand Knob
B2
A1
B2
J1
I
I
I
J1
B2
J2
B1
A1
B4
B3 B1
2. Remove the screw and washer at the top of the M10 Hand Knob and connect the M10 handle , C-clamp B1 and support plate with the screw
and washer that were just removed. Select the preferred height according to your desk thickness. Connect C-Clamp B1 to C-Clamp Brace B2 using M8x12
Bolt J1 , and tighten with Allen Key 5mm I . Rotate the hand knob N clockwise to fasten for stability.
B4 B4 B1 B3
B2
B1
B4
I
J2
Lower Pole
A1 (x1)
Upper Pole
C3 (x1)
Middle Pole
B2 (x1)
1
A3
A2
A2
A1
A2
A1
I
I
Option A : 39'' Pole Installation
A1
A3
Pre-Assembly
Loosen the screws on the Lower Pole a1 and Middle Pole a2 with Allen key
3mm o . Connect Lower Pole a1 , Middle Pole a2 and Upper Pole a3 by
tightening the screws with Allen key 3mm o to fix the three poles.
A1
A1
A2
I A2 A3
I

A3
3Put the Wire Clip and Swivel Arm d through the Upper Pole a , adjust the preferred height
and tighten using Allen Key 5mm o . Attach the Wire Clips to the Swivel Arm d .
7Manually swivel, tilt, and rotate the monitor for the best viewing angle.
6Guide the cable through the Wire Clips ( k , l ) and store the Allen Keys o in the Wire Clip k .
Adjust the tilt angle using Allen Key 5mm n .
KK
I
I
L
C
C
n1L
K
L
K
90°
90°
90°
90°
A3
C
I
Select bolts and spacers (if needed) according to your TV/Monitor. Attach the VESA Plate to the Monitor and tighten with a screwdriver. (Screwdriver not included)
Step 4.1
Select Monitor Screws Step 4.3a
Flat Back Monitor
Step 4.3b Curved or Recessed Back Monitor
D
D
G
H
F
M4x12 M4x30
4
Only one screw size fits your Monitor
Step 4.2
Select Spacers ( if needed )
Hand thread screws into the
threaded inserts on the back
of your Monitor to determine
which screw (M4x12 or M4x30)
to use.
5Put the assembled TV/Monitor onto the Swivel Arm d and tighten the VESA Plate e with
Nut h for stability.
h
d
D
C
E
Option B : Grommet Base Installation
1. Place Lower Pole a onto Grommet Base Plate m . Connect them from the bottom using M5x14
Bolt J1 and tighten with Allen Key 3mm .I
J1
A1 B5
I
A1
B5
J1
L
D
C
E
Notice: Please make sure the security
nut is installed before you
rotate the monitor.
E
E
Remove the screw and washer at the top of the M10 Hand Knob N .
If the existing grommet hole comes with a plastic protector, remove it to ensure a flat surface before
installing the desk mount.
Position the Pole A on the mounting surface and connect the hand knob N through the Support
Plate Q and the grommet hole with the Pole A . Rotate the hand knob N clockwise to fasten for
stability.
Remove the screw and washer at the top of the M10 Hand Knob N .
Mark the position of the hole on your mounting surface. Drill a 3/8"(10mm) diameter hole at the
marked position through the mounting surface.
Position the Pole A on the mounting surface and connect the hand knob N through the Support
Plate Q and the self-drilled hole with the Pole A . Rotate the hand knob N clockwise to fasten
for stability.
2a. Existing Grommet Hole Installation 2b. Self-drilled Grommet Hole Installation
A1
B3
B4
B4
B4
B4
A1
A1
B3
B4 A1
A1
B4
B4
B4
B3
A1
B3
B4
B4
I
I
I
K