Walls+Forms T2+ GENERIC User manual

Assembly Number:
Description:
Sheet
Number:
Date:
Drawn by:
UOM:
Scale:
Rev:
This drawing and all information and concepts contained thereupon is exclusive property,
and may not be reproduced in any form without the expressed written consent of:
204 Airline Drive, Suite
200,
Coppell, Texas 75019
P - 972 745 0800
F - 972 304 8402
www.wallsform.com
Part Number: PAGE (1)
N/A
GENERIC T2+ INSTRUCTIONS
N/A
02/28/2020
JVILLANUEVA
INCH
NTS
--
T2+ GENERIC
INSTRUCTIONS

Assembly Number:
Description:
Sheet
Number:
Date:
Drawn by:
UOM:
Scale:
Rev:
This drawing and all information and concepts contained thereupon is exclusive property,
and may not be reproduced in any form without the expressed written consent of:
204 Airline Drive, Suite
200,
Coppell, Texas 75019
P - 972 745 0800
F - 972 304 8402
www.wallsform.com
Part Number: PAGE (2)
N/A
GENERIC T2+ INSTRUCTIONS
N/A
02/28/2020
JVILLANUEVA
INCH
NTS
--
#8 X 1-1/2" PHILLIPS PAN HEAD SCREW
#8 X 2" PHILLIPS PAN HEAD SCREW
M6 X 20 SOCKET HEAD BOLT
M6 HEX NUT
M6 X 70 SOCKET HEAD BOLT
M10 X 40 BASE LEVELER
3/16" X 4" TOGGLE BOLT
3/16" X 2-3/4" CONCRETE SCREW
3/16" X 1-1/4" FLAT WASHER

Assembly Number:
Description:
Sheet
Number:
Date:
Drawn by:
UOM:
Scale:
Rev:
This drawing and all information and concepts contained thereupon is exclusive property,
and may not be reproduced in any form without the expressed written consent of:
204 Airline Drive, Suite
200,
Coppell, Texas 75019
P - 972 745 0800
F - 972 304 8402
www.wallsform.com
Part Number: PAGE (3)
N/A
GENERIC T2+ INSTRUCTIONS
N/A
02/28/2020
JVILLANUEVA
INCH
NTS
--
**NOTE**
ALL T2 RAILS SHOULD COME
PRE-INSTALLED, IN THE CASE OF
WANTING TO RELOCATE OR ADD A
T2+ RAIL. REMOVE M6 BOLTS
LOCATED TWO ON EACH END AND
PULL T2+ RAIL OUT AS SHOW.
REVERSE INSTRUCTIONS WHEN
ADDING A T2+ RAIL

Assembly Number:
Description:
Sheet
Number:
Date:
Drawn by:
UOM:
Scale:
Rev:
This drawing and all information and concepts contained thereupon is exclusive property,
and may not be reproduced in any form without the expressed written consent of:
204 Airline Drive, Suite
200,
Coppell, Texas 75019
P - 972 745 0800
F - 972 304 8402
www.wallsform.com
Part Number: PAGE (4)
N/A
GENERIC T2+ INSTRUCTIONS
N/A
02/28/2020
JVILLANUEVA
INCH
NTS
--
**NOTE**
IF WALL DISPLAY ONLY REQUIRES
ONE FRAME SKIP THIS STEP
STEP 1
PLACE T2+ FRAMES FACE DOWN ON
THE FLOOR, BOLT FRAMES TOGETHER
USING PROVIDED M6 X 70 BOLTS AND
M6 HEX NUTS AS SHOWN. SEE DETAIL
FOR CLARITY.

Assembly Number:
Description:
Sheet
Number:
Date:
Drawn by:
UOM:
Scale:
Rev:
This drawing and all information and concepts contained thereupon is exclusive property,
and may not be reproduced in any form without the expressed written consent of:
204 Airline Drive, Suite
200,
Coppell, Texas 75019
P - 972 745 0800
F - 972 304 8402
www.wallsform.com
Part Number: PAGE (5)
N/A
GENERIC T2+ INSTRUCTIONS
N/A
02/28/2020
JVILLANUEVA
INCH
NTS
--
**NOTE**
WHEN INSTALLING FURRING STRIPS, INSTALL TWO
FURRING STRIPS ON EACH END FRAME AND ONE PER
FRAME, STAGGERED TOP THEN BOTTOM IN BETWEEN THE
TWO END FRAMES
STEP 2
ATTACH THE FURRING STRIPS TO THE
FRAME BY INSERTING SECTIONAL
FITTINGS INTO T2+ FRAME AS SHOWN,
SECURE WITH M6 X 20 SOCKET HEAD
BOLTS. SEE DETAIL FOR CLARITY.
M6 X 20 SOCKET HEAD BOLT
SECTIONAL FITTING

Assembly Number:
Description:
Sheet
Number:
Date:
Drawn by:
UOM:
Scale:
Rev:
This drawing and all information and concepts contained thereupon is exclusive property,
and may not be reproduced in any form without the expressed written consent of:
204 Airline Drive, Suite
200,
Coppell, Texas 75019
P - 972 745 0800
F - 972 304 8402
www.wallsform.com
Part Number: PAGE (6)
N/A
GENERIC T2+ INSTRUCTIONS
N/A
02/28/2020
JVILLANUEVA
INCH
NTS
--
STEP 3
STAND T2+ FRAME(S) UPRIGHT
AGAINST DRYWALL. MAKE SURE THAT
THE FRAME(S) IS LEVEL WITH THE
FLOOR.
DETAIL AREA
DRILL HERE
STEP 4
DRILL HOLES WITH 5/8" DRILL BIT, TWO
HOLES PER FURRING STRIP.
STEP 5
INSERT TOGGLE BOLT AND FLAT
WASHER INTO HOLES DRILLED. DO NOT
OVER TIGHTEN.

Assembly Number:
Description:
Sheet
Number:
Date:
Drawn by:
UOM:
Scale:
Rev:
This drawing and all information and concepts contained thereupon is exclusive property,
and may not be reproduced in any form without the expressed written consent of:
204 Airline Drive, Suite
200,
Coppell, Texas 75019
P - 972 745 0800
F - 972 304 8402
www.wallsform.com
Part Number: PAGE (7)
N/A
GENERIC T2+ INSTRUCTIONS
N/A
02/28/2020
JVILLANUEVA
INCH
NTS
--
STEP 6
ATTACH THE END PLATES TO WALL UNIT WITH
#8 X 1-1/2" PHILLIP PAN HEAD SCREW. THE T2+
FRAME(S) MAY NEED TO BE ADJUSTED SO
THAT THE FRAME IS FLUSH WITH THE FRONT
EDGE OF END PLATES AND THE BACK IS
AGAINST THE WALL. SEE DETAILS FOR
CLARITY.
#8 X 1-1/2" PHILLIPS
3/16" X 1-1/4" FLAT WASHER
PAN HEAD SCREW
BACK EDGE OF END
PLATE SHOULD BE
TOUCHING THE WALL
ADJUST THE WALL
UNIT SO THAT END
END PLATE IS FLUSH
WITH FRAME

Assembly Number:
Description:
Sheet
Number:
Date:
Drawn by:
UOM:
Scale:
Rev:
This drawing and all information and concepts contained thereupon is exclusive property,
and may not be reproduced in any form without the expressed written consent of:
204 Airline Drive, Suite
200,
Coppell, Texas 75019
P - 972 745 0800
F - 972 304 8402
www.wallsform.com
Part Number: PAGE (8)
N/A
GENERIC T2+ INSTRUCTIONS
N/A
02/28/2020
JVILLANUEVA
INCH
NTS
--
STEP 7
LOCATE T2 PLATES AND ATTACH ONE ROW OF PLATES AS SHOWN. INSERT SCREW
HEADS LOCATED ON BACK OF T2 PLATE INTO THE KEY HOLES LOCATED ON T2+ FRAME(S).
PUSH DOWNWARD TO LOCK IN PLACE. USE THE ROW OF PLATES AS A REFERENCE, LEVEL
THE FRAME(S) BY TURNING THE BASE LEVELER WITH A WRENCH. BASE LEVELERS ARE
LOCATED AT THE BOTTOM OF T2+ FRAME(S). SEE DETAILS FOR CLARITY.
KEY HOLE
LEVEL ALONG THE ROW OF PLATES

Assembly Number:
Description:
Sheet
Number:
Date:
Drawn by:
UOM:
Scale:
Rev:
This drawing and all information and concepts contained thereupon is exclusive property,
and may not be reproduced in any form without the expressed written consent of:
204 Airline Drive, Suite
200,
Coppell, Texas 75019
P - 972 745 0800
F - 972 304 8402
www.wallsform.com
Part Number: PAGE (9)
N/A
GENERIC T2+ INSTRUCTIONS
N/A
02/28/2020
JVILLANUEVA
INCH
NTS
--
**NOTE**
USE A 17MM WRENCH, NOT
PROVIDED. TURN WRENCH
CLOCKWISE TO LOWER THE
FRAME(S) UP. TURN WRENCH
COUNTER-CLOCKWISE TO RAISE THE
FRAME(S)
DETAIL AREA
BOTTOM OF
M10 X 40 BASE LEVELER
T2+ FRAME

Assembly Number:
Description:
Sheet
Number:
Date:
Drawn by:
UOM:
Scale:
Rev:
This drawing and all information and concepts contained thereupon is exclusive property,
and may not be reproduced in any form without the expressed written consent of:
204 Airline Drive, Suite
200,
Coppell, Texas 75019
P - 972 745 0800
F - 972 304 8402
www.wallsform.com
Part Number: PAGE (10)
N/A
GENERIC T2+ INSTRUCTIONS
N/A
02/28/2020
JVILLANUEVA
INCH
NTS
--
STEP 8
AFTER MAKING SURE FRAME(S) ARE
LEVEL, TIGHT ALL SCREWS AND BOLTS
ON FRAME(S), WALL MOUNTS AND
FURRING STRIPS.
DETAIL AREA
STEP 9
LOCATE WALL STUDS AND REINFORCE
FURRING STRIPS WITH #8 X 2" DRYWALL
SCREWS AND 3/16" X 1-1/4" FLAT
WASHERS
WALL STUD
WALL STUD
WALL STUD
WALL STUD
WALL STUD
WALL STUD
WALL STUD
WALL STUD