walraven 6901975 User manual

walraven.com walraven.com
Walraven Wall Mounting Set 62 | H
ISO hdg L = 750 mm and L = 900 mm
Part No. 6901975 (L = 750 mm), 6901990 (L = 900 mm)
and 6901998 (ISO Kit for female thread units)
EN Assembly instruction
DE Montageanleitung
NL Montage-instructie
FR Instructions de montage
ES Instrucciones de montaje
PT Instrução de montagem
PL Instrukcja montażu
CZ Montážní návod
SK Montážny návod
RO Instrucțiuni de montaj
UA Інструкція з монтажу
DK Monteringsvejledning
SE Monteringsanvisninga
NO Montasjeanvisning
IT Istruzioni di montaggio
[phone]
UK
[phone]
DE
[phone]
NL
[phone]
BE
[phone]
CZ / SK
[phone]
PL
[phone]
FR
[phone]
ES [phone]
US
[phone]
UA
[phone]
HU
[phone]
DK
[phone]
SE
[phone]
NO
[phone]
GR
CN [phone]
[phone]
SG
Other countries
[phone]
Part No. L (mm) Fa,z (kg)
6901975 750 120
Part No. L (mm) Fa,z (kg)
6901990 900 180
4x
4x
4x
4x
4x
4x
4x
4x
2x
2x
2x
2x
2x
2x
2x
2x
2x
2x
4x
4x
Step 3a:
Mount the brackets on the female thread of the unit.
Slide Nuts need to be straight with the bracket.
There are two types of brackets, type 1 with the damper in the middle and type 2
with the damper at the end. Type 1 needs to be positioned on the inner side.
Part no. 6901998 (ISO Kit for female thread units)
Installation
Note: This assembly set is only required for devices
with female thread on the underside to mount the unit
Step 1:
Unscrew the dampers from the standard Wall Mounting Set including slide nuts.
The U-washers, round washers and nuts are not needed, take them off.
Step 2:
Screw the dampers (handtight) on the U-shaped brackets in the open hole by
using the slidenuts.
Step 3b:
Position the unit with the mounted U-shaped brackets on the Wall Mounting Set.
Push the screw down and turn 90° to close the fasteners
(check the right t before tightening; T = 40Nm).
1
2
3a
3b
90°
Type 2Type 1
M8: 25Nm
M10: 40Nm
9660000189 - Assembly Instruction Walraven Wall Mounting Set 62|H ISO hdg L=750mm and L=900mm - 08/2023 - pdf - Full content subject to modications

walraven.com walraven.com
Part No. 6901975 (L = 750 mm)
Installation
Walraven RapidStrut®slidenuts - Correct Use!
walraven.com
RapidStrut® / Strut slidenuts - Correct Use!
9660000201 - Strut Slidenuts - Correct Use! - 05/2022 - Subject to modications
B
TB
T
200 508
819
750
Note: Select suitable screws and anchors to secure the system rails on the wall.
If the load bearing capacity of the wall cannot be guaranteed, do not use the wall mounting bracket.
Walraven has an extensive range of anchors and fasteners suitable for this application.
M8: 25Nm
M10: 40Nm
Part No. 6901990 (L = 900 mm)
Installation
B
TB
T
400
808
970
900
Walraven RapidStrut®slidenuts - Correct Use!
walraven.com
RapidStrut® / Strut slidenuts - Correct Use!
9660000201 - Strut Slidenuts - Correct Use! - 05/2022 - Subject to modications
Note: Select suitable screws and anchors to secure the system rails on the wall.
If the load bearing capacity of the wall cannot be guaranteed, do not use the wall mounting bracket.
Walraven has an extensive range of anchors and fasteners suitable for this application.
M8: 25Nm
M10: 40Nm