1. Press PGM button followed by MODE button (a small S symbol appears bottom of screen)
2. Press and hold DAY button until all seven days of the week are displayed
3. Press HOUR and MIN buttons to set first on period
4. Press PGM then HOUR and MIN buttons to set first off period
5. Press PGM then HOUR and MIN buttons to set second on period
6. Press PGM then HOUR and MIN buttons to set second off period
7. Press RETURN to resume normal operation.
Note: To remove a heating period press PGM until time is displayed then press CLEAR.
1. Press TEMP button
2. Press sor ▼keys to set desired temperature.
3. Press RETURN
1. Select MANUAL MODE
2. Press sor ▼keys to set desired temperature.
3. Press RETURN
This completes basic programming
INSTALLERS BASIC PROGRAMMING GUIDE
Programme Day and Time
(WITH THERMOSTAT TURNED ON)
1.
Press DAY and view displayed day. Press sor tarrows to set the day
2.
Press HOUR and view current hour. Press sor tarrows to set the hour
3.
Press MIN and view current minutes. Press sor tarrows to set the minutes
Programming Automatic Operating Times
(Factory default –all seven days)
First heat period 0600 ON
0800 OFF
Second Heating Period 1800 ON
2130 OFF
To customize time settings
1. Press PGM (first symbol appears) to set First heat up period ON time.
2. Press and hold DAY button until all seven days of the week are displayed.
3. Press HOUR button until first heat up hour is reached
4. Press MINUTE button until first heat up minute is reached
5. Press PGM (second symbol appears) to set First heat up period OFF time.
6. Press HOUR and then MINUTE buttons as above to set first heat up period OFF
time.
7.
Press PGM. Repeat steps 3 to 6 as above to set second heating period.
8.
Press RET to exit programme
Note: If a key is not pressed when setting heat times within 20 seconds, you will need to press programme
button until you reach the heating period you wish to alter (indicated by symbol)
Programme Weekend Times
1. Press PGM.
2. Press DAY button until Saturday is displayed
3. Repeat the process (3 -8 as above) to set 1
st and 2nd heat up periods for Saturday
4. Once Saturday has been programmed press DAY to step to Sunday
and set times
as previous
5.
Press RETURN to exit program.
Note: To remove a heating period press PGM until time is displayed then press CLR.
ADVANCED PROGRAMMING OPTIONS
Alter Sensor Type
(THERMOSTAT TURNED OFF)
•Press TEMP until desired method is indicated as below:
1.
Floor Sensing
2.
Air Sensing
3.
Air Sensing with floor limiting temperature
Setting Maximum and Minimum Temperatures
(THERMOSTAT TURNED OFF)
•Press and hold WATTS button for 3 seconds
•Press MODE to toggle and view temperature
(Note 1 & 2 symbol appears at bottom of screen)
1. Floor Temperature Maximum (default setting 30°C)
2. Floor Temperature Minimum (default setting 5°C)
•Use sand tbuttons to adjust temperature settings
•Press RETURN to exit
Enable/Disable Power Indicator
(THERMOSTAT TURNED ON)
•Press WATTS button to toggle Power Indicator (displayed bottom right) to ON or OFF
•Press CLEAR to delete accumulated value
Programming Cable Size for Power Meter Function
(THERMOSTAT TURNED OFF)
•Press sand tkeys to set to closest Cable Wattage value
Note: This is for indication only to assist achieving lowest consumer running
costs (see owners operating instructions)
Reset to Default
(THERMOSTAT TURNED OFF)
•Press and hold PGM for 15 seconds (OFF flashes)
•Press RETURN within 5 seconds to reset.
To customize time settings
1. Press PGM (first symbol appears) to set First heat up period ON time.
2. Press and hold DAY button until all seven days of the week are displayed.
3. Press HOUR button until first heat up hour is reached
4. Press MINUTE button until first heat up minute is reached
5. Press PGM (second symbol appears) to set First heat up period OFF time.
6. Press HOUR and then MINUTE buttons as above to set first heat up period OFF time.
7. Press PGM. Repeat steps 3 to 6 as above to set second heating period.
8. Press RET to exit programme
Note: If a key is not pressed when setting heat times within 20 seconds, you will need to press
programme button until you reach the heating period you wish to alter (indicated by symbol)
Programme Weekend Times
1. Press PGM.
2. Press DAY button until Saturday is displayed
3. Repeat the process (3 - 8 as above) to set 1st and 2nd heat up periods for Saturday
4. Once Saturday has been programmed press DAY to step to Sunday and set times as previous
5. Press RETURN to exit program.
Note: To remove a heating period press PGM until time is displayed then press CLR.
2. Installers Basic Programming Guide continued
4. Advanced Programming Options
Alter Sensor Type
(WITH THERMOSTAT TURNED OFF)
• Press TEMP until desired method
is indicated as below:
1. Floor Sensing
2. Air Sensing
3. Air Sensing with floor
limiting temperature
Setting Maximum and Minimum Temperatures
(WITH THERMOSTAT TURNED OFF)
• Press and hold WATTS button for 3 seconds
• Press MODE to toggle and view temperature
(Note 1 & 2 symbol appears at bottom of screen)
1. Floor Temperature Maximum, adjustable from 16°C to 35°C (default setting 30°C)
2. Floor Temperature Minimum, adjustable from 5°C to 20°C (default setting 18°C)
• Use sand ▼buttons to adjust temperature settings
• Press RETURN to exit
Enable/Disable Power Indicator
(WITH THERMOSTAT TURNED ON)
• Press WATTS button to toggle Power Indicator (displayed bottom right) to ON or OFF
• Press CLEAR to delete accumulated value
Programming Cable Size for Power Meter Function
(WITH THERMOSTAT TURNED OFF)
• Press sand ▼keys to set to closest Cable Wattage value
Note: This is for indication only to assist achieving lowest consumer running costs
(see owners operating instructions)
Reset to Default
(WITH THERMOSTAT TURNED OFF)
• Press and hold PGM for
15 seconds (OFF flashes)
• Press RETURN within 5 seconds to reset.
Thermostat Lock/Unlock
• Press power button for 6 seconds to lock.
• Press return for 6 seconds to unlock.
3. Additional Installers Options
Programming Automatic Operating Times
(Factory default – all seven days)
First heat period 00:-- ON
00:-- OFF
Second Heating Period 00:-- ON
00:-- OFF
ADDITIONAL INSTALLERS OPTIONS
HEATED TOWEL RAIL
(To alter factory default on/off times)
Programming Automatic Operating Times
(Factory default –all seven days)
First heat period 0600 ON
0900 OFF
Second Heating Period 1800 ON
2100 OFF
1. Press PGM button followed by MODE button (a small
S
symbol appears bottom of
screen)
2. Press and hold DAY button until all seven days of the week are displayed
3. Press HOUR and MIN buttons to set first on period
4. Press PGM then HOUR and MIN buttons to set first off period
5. Press PGM then HOUR and MIN buttons to set second on period
6. Press PGM then HOUR and MIN buttons to set second off period
7. Press RETURN to resume normal operation.
Note: To remove a heating period press PGM until time is displayed then press CLEAR.
Programming Temperature Set Point
Default set point 22 Deg Celsius (floor sensing)
1. Press TEMP button
2. Press
s
or
t
keys to set desired temperature.
3. Press RETURN
This completes basic programming
ADVANCED PROGRAMMING OPTIONS
INSTALLERS BASIC PROGRALLERS BASIC PROGRAMMING
GUIDE
ADDITIONAL INSTALLERS OPTIONS
HEATED TOWEL RAIL
(To alter factory default on/off times)
Programming Automatic Operating Times
(Factory default –all seven days)
First heat period 0600 ON
0900 OFF
Second Heating Period 1800 ON
2100 OFF
1. Press PGM button followed by MODE button (a small
S
symbol appears bottom of
screen)
2. Press and hold DAY button until all seven days of the week are displayed
3. Press HOUR and MIN buttons to set first on period
4. Press PGM then HOUR and MIN buttons to set first off period
5. Press PGM then HOUR and MIN buttons to set second on period
6. Press PGM then HOUR and MIN buttons to set second off period
7. Press RETURN to resume normal operation.
Note: To remove a heating period press PGM until time is displayed then press CLEAR.
Programming Temperature Set Point
Default set point 22 Deg Celsius (floor sensing)
1. Press TEMP button
2. Press
s
or
t
keys to set desired temperature.
3. Press RETURN
This completes basic programming
ADVANCED PROGRAMMING OPTIONS
INSTALLERS BASIC PROGRALLERS BASIC PROGRAMMING
GUIDE
Programming Temperature Set Point (Auto Mode)
Default set point 24 Degrees Celsius (floor sensing)
INSTALLERS BASIC PROGRAMMING GUIDE
Programme Day and Time
(WITH THERMOSTAT TURNED ON)
1.
Press DAY and view displayed day. Press sor tarrows to set the day
2.
Press HOUR and view current hour. Press sor tarrows to set the hour
3.
Press MIN and view current minutes. Press sor tarrows to set the minutes
Programming Automatic Operating Times
(Factory default –all seven days)
First heat period 0600 ON
0800 OFF
Second Heating Period 1800 ON
2130 OFF
To customize time settings
1. Press PGM (first symbol appears) to set First heat up period ON time.
2. Press and hold DAY button until all seven days of the week are displayed.
3. Press HOUR button until first heat up hour is reached
4. Press MINUTE button until first heat up minute is reached
5. Press PGM (second symbol appears) to set First heat up period OFF time.
6. Press HOUR and then MINUTE buttons as above to set first heat up period OFF
time.
7.
Press PGM. Repeat steps 3 to 6 as above to set second heating period.
8.
Press RET to exit programme
Note: If a key is not pressed when setting heat times within 20 seconds, you will need to press programme
button until you reach the heating period you wish to alter (indicated by symbol)
Programme Weekend Times
1. Press PGM.
2. Press DAY button until Saturday is displayed
3. Repeat the process (3 -8 as above) to set 1st and 2nd heat up periods for Saturday
4. Once Saturday has been programmed press DAY to step to Sunday
and set times
as previous
5.
Press RETURN to exit program.
Note: To remove a heating period press PGM until time is displayed then press CLR.
Programme Day and Time
(WITH THERMOSTAT TURNED ON)
1. Press DAY and view displayed day. Press sor ▼arrows to set the day
2. Press HOUR and view current hour. Press sor ▼arrows to set the hour
3. Press MIN and view current minutes. Press sor ▼arrows to set the minutes
Programming Automatic Operating Times
(Factory default – all seven days)
First heat period 0600 ON
0800 OFF
Second Heating Period 1800 ON
2130 OFF
1. Installers Basic Programming Guide
ADVANCED PROGRAMMING OPTIONS
Alter Sensor Type
(THERMOSTAT TURNED OFF)
•Press TEMP until desired method is indicated as below:
1.
Floor Sensing
2.
Air Sensing
3.
Air Sensing with floor limiting temperature
Setting Maximum and Minimum Temperatures
(THERMOSTAT TURNED OFF)
•Press and hold WATTS button for 3 seconds
•Press MODE to toggle and view temperature
(Note 1 & 2 symbol appears at bottom of screen)
1. Floor Temperature Maximum (default setting 30°C)
2. Floor Temperature Minimum (default setting 5°C)
•Use sand tbuttons to adjust temperature settings
•Press RETURN to exit
Enable/Disable Power Indicator
(THERMOSTAT TURNED ON)
•Press WATTS button to toggle Power Indicator (displayed bottom right) to ON or OFF
•Press CLEAR to delete accumulated value
Programming Cable Size for Power Meter Function
(THERMOSTAT TURNED OFF)
•Press sand tkeys to set to closest Cable Wattage value
Note: This is for indication only to assist achieving lowest consumer running
costs (see owners operating instructions)
Reset to Default
(THERMOSTAT TURNED OFF)
•Press and hold PGM for 15 seconds (OFF flashes)
•Press RETURN within 5 seconds to reset.
ADDITIONAL INSTALLERS OPTIONS
HEATED TOWEL RAIL
(To alter factory default on/off times)
Programming Automatic Operating Times
(Factory default –all seven days)
First heat period 0600 ON
0900 OFF
Second Heating Period 1800 ON
2100 OFF
1. Press PGM button followed by MODE button (a small
S
symbol appears bottom of
screen)
2. Press and hold DAY button until all seven days of the week are displayed
3. Press HOUR and MIN buttons to set first on period
4. Press PGM then HOUR and MIN buttons to set first off period
5. Press PGM then HOUR and MIN buttons to set second on period
6. Press PGM then HOUR and MIN buttons to set second off period
7. Press RETURN to resume normal operation.
Note: To remove a heating period press PGM until time is displayed then press CLEAR.
Programming Temperature Set Point
Default set point 22 Deg Celsius (floor sensing)
1. Press TEMP button
2. Press
s
or
t
keys to set desired temperature.
3. Press RETURN
This completes basic programming
ADVANCED PROGRAMMING OPTIONS
INSTALLERS BASIC PROGRALLERS BASIC PROGRAMMING
GUIDE
Programming Temperature Set Point (Manual Mode)
Default set point 24 Degrees Celsius (floor sensing)
