Warren Evans Chester Ottoman User manual

Stockport Ottoman Minster Ottoman Ripley Ottoman
Richmond Ottoman
Chester Ottoman (Wooden)
Ludlow Ottoman
Oxford Ottoman (Wooden)
ASSEMBLY GUIDE
New Upholstered and Wooden Space Saving Ottoman Bed Range
handmade in London

2
1.
2.
3.
When unwrapping these beds please keep all the wrapping intact should it be needed for
returns. Make a space in your bedroom for where the bed will actually be positioned.
Start the assembly process by leaning the head end against the wall of choice.
Open the 3 largest boxes, one of which contains both the foot end and the head end of the
bed (this box also contains screws, bolts and allen key inside).
Place the head end on its feet leaning against your wall of choice. Place the foot end on its
feet to one side. (Do not slide the headboard onto the head end until instructed to do so).
There are 12 bolts, 3 that go in each of the legs. Put each bolt in but only one full turn so
that it’s loosely connected.
Bolts x 12
Head End
Please make sure that all the surfaces that you lean any of our products on are clean and soft so
as not to mark or damage the bed.
Please ensure that you wash your hands or that your gloves are very clean even after and during
unwrapping the products, to not mark the finished product in any way. We wish you to have an
excellent clean Warren Evans bed!
PLEASE READ THE USER GUIDE BEFORE FOLLOWING THESE INSTRUCTIONS

3
4.
Hook the bracket (C) over the bolts (D), one
side at a time, onto the headboard first.
Then hook the foot end to the other end of
the sides.
Make sure that the sides of the bed are
facing up
UP
Make sure the exterior of the side (A) overlaps the head end (B).
The metal ottoman lifting mechanism must go at the head end of the bed.
(A)
(D)
(C)
(B)

4
Unwrap the lightest long package carefully. There are 3x cross beams (A), a slat with ply
support (B) and a slat with a handle (C) which will be used later.
5.
Place the 3x cross beams (A) into the cut out slots which appear on the inside of the side
panels, at the bottom.
ottoman base
(B)
(C)
(A)
Head End
Foot End

5
Please unwrap the rectangular thin box. Place the 8 base plates into the frame as shown.
Starting with the head end first and make your way down to the foot end.
7.
Now using just your fingers tighten all 12 bolts as much as possible all the way around all 4 legs.
6.
Head End Head End
Foot End Foot End
Shown here is an aerial view looking down on your bedframe, please ‘square it up’ so that it
is not ridiculously out of kilt.
Now tighten the 12 bolts firmly (but not super tight) with the allen key provided.
AERIAL VIEW

6
If your bed is a super king size or a small super king size (6ft or 5ft 6inch wide) you will
need to insert the centre beam.
8.
Take the 2 slats (head end (B) and foot end (C)) that are available and place them onto the
bed as shown.
The edge of the head end slat (the ply mattress buffer faces upwards and is at the head
end of the bed as shown) should sit at the edge of the lifting mechanism wooden rail.
The foot end slat with the handle should have the label facing upwards that reads ‘Please
use with a mattress’ and should also sit at the edge of the lifting mechanism wooden rail.
The tips of both ends of every slat should equal distance from the sides.
9.
Head End
Hoop-lock screws
Foot End
The hoop-lock screws should remain firmly screwed down in place.
(B)
(C)

7
Please space the foot end slat appropriately and screw down all 4 screws, and now do the
same with the head end slat. Please continue the same process with all of the other slats,
which are in the last package to be opened. Please spread these slats out so that they are
equally spaced in between the first and last slat.
The tips of both ends of every slat should equal distance from the sides. The hoop-lock
screws should remain firmly screwed down in place.
10.
With 2 people please lift the headboard up (with clean hands!) and keeping it level, slide
it down fully onto the headboard posts.
11.
Head End Head End
Foot End Foot End

8
IMPORTANT:
LAST STEP OF YOUR BED ASEEMBLY
The 2 hoop-lock screws at the foot end of
each side of the bed must be completely
unscrewed and then screwed back in 4
turns to keep it conveniently located for use
whenever your bed is to be moved. Failure to
remove far enough before use could scratch
the stationary side rail and damage it.
AND THE FIRST STEP IF EVER MOVING /
DISASEMBLING YOUR BED.
Failure to use it when moving the bed
creates an injury risk as this screw keeps
the ottoman sides from flipping up
unexpectedly.
The hoop-lock screws shown must be
completely screwed in. So that the ottoman
can no longer be raised until a mattress is
about to be placed on it again for normal use.
To disassemble reverse the order of the
assembly instructions, but first number the
slats as shown (1, 2, 3, 4, 5 etc...) so that
they screw back into the same places when
reassembling.
Make sure hands, surfaces are clean and all
of the parts of the bed do not get damaged
against rough or hard surfaces. Thank you.
12.
DISASSEMBLING YOUR BED