Wasserstein 3-in-1 Smart Floodlight, Charger & Mount for Wyze Cam... User manual

USER MANUAL
3-in-1 Floodlight, charger and mount
for Wyze Cam Pan V2

EVA gasketUSB cable
2 x screwsfloodlight 1 x screw cap1 x crossbar
3 x wire nuts
1 x plastic screw insert 1 x metal screw 1 x silicone skin 2 x flat silicone rings
1x metal plate
In the Box
Page 1
Safety Information
• Disassembling the light head is not recommended as it may cause
damage to internal components. The floodlight may not function
properly after disassembly.
• Turn the main circuit OFF before installation.
• DO NOT remove the protective LED lens.
• DO NOT look directly at LEDs that are turned on for any length of time.
• DO NOT leave bare wires exposed outside the wall canopy enclosure.
• Mount the floodlight on the wall shaded from the rain and not to be
splashed by direct rainfall.

Page 2
Installing Your Floodlight
1. Make sure you have all the included materials.
2. You will be working with electrical wires during the installation process.
For safety reasons, shut off the power to your floodlight at the circuit
breaker.
1. Remove your existing floodlight from the junction box, and disconnect
the wires. If there is a crossbar attached to your junction box, remove it
also.
Preinstallation
If you have an existing floodlight
Note: If you are unfamiliar with electrical installations, we highly
recommend hiring a professional electrician to perform the installation.

2a. Remove the protective tape from the EVA gasket. Press the adhesive
side firmly against the rear of the floodlight.
2b. Ensure that the center screw hole and wire slot of the foam gasket
are aligned with the screw hole and wire slot.
1. Attach the crossbar included in the package to the junction box with
the screws.
Installing the floodlight to the junction box
2. Remove the crossbar attached to your junction box.
Page 3

Page 4
1. Connect the green and yellow wire from the floodlight to the existing
ground wire inside the junction box. Use the included wire nut to
connect the wires properly.
2. Using a wire nut, connect the white neutral wire from the floodlight
to the neutral wire of the junction box.
3. Using a wire nut, connect the black hot wire from the floodlight to
the hot wire of the junction box.
Wiring the floodlight and junction box through the EVA gasket
The white wire on your floodlight is neutral wire.
The black wire on your floodlight is hot wire.
Neutral Wire (White)
Hot Wire (Black)
Ground Wire (Copper)
Junction Box
Wire Nuts
4a. Make sure the wire connections are secured. Carefully place the
wires into the junction box.

Page 5
4b. Mount the floodlight onto the crossbar and secure it with the screw
cap provided.
5. Switch on the electricity, checking that the wiring has been done
correctly and that the floodlight turns on.
Important: Before mounting the floodlight, completely apply the EVA
gasket around the perimeter of the cover plate where the back of the
cover plate meets the mounting surface. This prevents water from
seeping into the junction box.
Note: The floodlight will provide continuous charging to the USB port
24/7, however, the motion sensor will only get triggered and turn the
lights on when it is dark outside (i.e., during nighttime).
Mounting Your Camera
1. Wear the silicone skin on the camera.
2. Flip the camera upside down. Place a silicone ring on top of the metal
plate and use the metal screw to secure the camera.
Step 1 Step 2

Page 6
3. Place another silicone ring on top of the other side of the metal plate
vertically, use the plastic screw insert to screw on the floodlight mounting
screw.
4. Open the USB port cap of the floodlight and connect the cable.
Press in firmly.
5. Connect the other micro-USB end to the camera female micro-USB port.
6. Adjust the camera to your preferred viewing angle.
Remark: You have to rotate the image 180 degrees in the Wyze App.
Step 3 Step 4
Step 5 Step 6

Page 7
FAQ
1. One or more floodlight(s) is flashing on and off. What's going on?
There are several possibilities. Try the following items:
• Check your connection to the house power.
• Check the area around the floodlight. There may be something in the
area (e.g. a small animal) that is triggering it.
2. A floodlight will not turn on. What's going on?
There are several possibilities. Try the following items:
• Check your connection to the house power.
• Leave the area for 10 minutes to give time for the floodlight to reset
without you triggering them. Return and check the floodlight by turning
off the power for at least a minute, then turning it back on.
• Make sure you are testing the floodlight in darkness.
Specifications
Materials:
Sensor angle range:
Sensor thresholds:
Max LED light intensity:
Color temperature:
Power:
PC + Aluminum
120°
13 to 33 ft (4 to 10 m)
2000 Lumens
5500 - 6500 k
AC 120 V

Get More Support
Scan the QR code below or email us at [email protected].
Made in China
www.wasserstein-home.com
Wyze Cam Pan V2 is not included.
Wyze Cam Pan V2 is a trademark of Wyze Labs, Inc.
Wasserstein is not affiliated with Wyze Labs, Inc.
Wasserstein is a trademark of Dropcases Ltd.