WatchBot Home Security Camera User manual

1
WatchBot Home Security Camera - User Guide
User Guide
Revision 3 - Dec 2011

2
WatchBot Home Security Camera - User Guide
Contents
SECTION PAGE
Introducon and Safety 4
Product Overview and Basic Features 5
Camera Diagram 6
1 QuickSetupGuideandOperaon   7
1.1 The WatchBot camera 7
1.2 Connect Camera and Components 8
1.3 Install the WatchBot Camera Tool soware 8
1.4 Run the WatchBot Camera Tool soware 9
1.5 Seng up your camera on your Local Area Network (LAN) 9
1.5.1 Important informaon about Microso AcveX Controls 10
1.6 Operator Controls - Basic Camera Operaon 11
1.6.1 Pan/Tilt (P/T) Controls 11
1.6.2 Patrol 11
1.6.3 I/O Switch On/O 11
1.6.4 Flipping the feed image 11
1.6.5 Pre-Posioning Buons 12
1.6.6 Screen Resoluon/Mode 12
1.6.7 Brightness and Contrast 12
1.6.8 Default Sengs 12
1.7 Visitor Controls - Recording Video and Audio 12
1.7.1 Mul-View 13
1.7.2 Add Timestamp 13
1.7.3 On-Screen Display (OSD) 13
1.7.4 Audio Buer 13
1.7.5 Live feed On/O and Snapshot 13
1.7.6 Recording Video and Audio 13
1.7.7 Moon Sensor, Alarm and Email Alert 13
2 SengupyourcameraforaccessviatheInternet 14
2.1 Seng up Network Sengs 14
2.1.1 Administrator | Basic Network Sengs 14
2.1.2 Administrator | UPnP Sengs 14
2.2 Visit the web page assigned to your camera 15
3 AdvancedSetupGuide     16
3.1 Administrator Sengs 16
3.1.1 Device Info 16
3.1.2 Alias Sengs 16
3.1.3 Date and Time Sengs 17
3.1.4 User Sengs 17
3.1.5 Mul-Device Sengs 18
3.1.6 Basic Network Sengs 19

3
WatchBot Home Security Camera - User Guide
3.1.7 Wireless LAN Sengs 19
3.1.7.1 Using your WatchBot camera wirelessly 19
3.2 Windows Live Messenger (MSN) Sengs 21
3.2.1 Create an MSN account for your camera 21
3.2.2 Add contact’s details 21
3.2.3 Add the camera as a contact in MSN 21
3.2.4 ‘Chat’ with your camera! 22
3.3 DDNS Sengs 22
3.4 Mail Service Sengs 23
3.4.1 Enter the sender email sengs 23
3.4.2 Enter the receiving email address(s) 23
3.4.3 Mail Server Sengs 23
3.4.4 Save and Test 23
3.5 FTP Service Sengs 24
3.5.1 Save and Test 24
3.6 Alarm Service Sengs 24
3.6.1 Arming moon detecon 24
3.6.2 Moon Detect Sensivity 24
3.6.3 Alarm Input Armed 25
3.6.4 I/O Linkage on Alarm 25
3.6.5 Seng up I/O linkage hardware 25
3.6.6 Send Alarm Nocaon by Mail 25
3.6.7 Upload Image on Alarm 25
3.6.8 Scheduler 25
3.6.9 Save sengs 25
3.7 PTZ Sengs 26
3.8 Upgrade Device Firmware 26
3.9 Backup/Restore Sengs 26
3.10 Restore Factory Sengs 26
3.11 Reboot Device 26
3.12 Log 26
3.13 Back 26
4 Usingotherbrowserstoaccesscamerawebinterface 27
4.1 Logging in on your PC, Mac or Tablet 27
4.1.1 The Web Interface 27
4.2 Logging in on a mobile device (eg. Symbian/Android browsers) 28
4.2.1 The Web Interface 28
5 FrequentlyAskedQuesons(FAQs)   29
6 Glossary       31
SECTION PAGE
APPENDIX - EXTRA ROUTER CONFIGURATION 33
Accessing the camera locally without the Camera Tool soware (Mac Users) 40

4
WatchBot Home Security Camera - User Guide
Introducon&safety
Congratulaons on the purchase of your new WatchBot home security camera. Please read
this manual correctly as it will help you to use the camera correctly and understand it’s
funcons and features.
Beforeinstalling
Before installing and using the camera, please read all the safety instrucons below carefully.
Installaonenvironment
The WatchBot camera is designed to be used indoors. The manufacturer and distributor
assume no liability for damage arising from using the device outdoors.
• Working temperature is limited to between 0°C - 50°C and humidity is limited to
between 5% - 90%.
• Avoid inammable and explosive environments;
• Do not expose to excessive vibraon and do not place other items on the camera;
• Avoid installing near strong magnec or electrical elds that could damage the unit;
• Always ensure the installaon environment is well venlated;
Transportaonandcarrying
The camera packaging ensures the device will not be accidentally damaged during transport.
In handling the unit, it is best to use the original packaging. Avoid moving the camera between
extremely cold and hot environments which may result in condensaon forming.
Maintenanceandprotecon
• Please refrain from opening the camera housing to avoid damage and risk of
electric shock.
• Please only use the original power adapter. Use of unauthorised power adapters
can damage the camera.
• Touching the camera lens will leave ngerprints and cause image blurring.
• Do not immerse in liquid; this may cause the camera hardware to short circuit and
become a re hazard.
What'sinthebox?
Item Quanty
WatchBot Home Security Camera 1
Wi-Fi Antenna 1
Soware CD 1 (includes User Manual/Soware)
DC Power Supply (5V 2A) 1
Network Cable 1
Mounng bracket 1

5
WatchBot Home Security Camera - User Guide
Productoverview
WatchBot is an integrated wireless IP Camera soluon. It combines a high quality digital video
camera with network connecvity and a powerful web server, allowing you to view live video
on your Desktop PC, Laptop or Mobile device using your local network or remotely over the
Internet. The basic funcon of the WatchBot is transming remote video over an IP network.
The high quality video image can be transmied with up to 30fps speed over a LAN/WAN by
using MJPEG hardware compression technology.
The WatchBot is based on the TCP/IP standard. There is a web server inside which supports
modern web browsers, making management and maintenance of your device simple and
intuive. You can use the WatchBot camera to remotely monitor, for example, your home,
oce, car or pets. Controlling the camera and managing the live video image is easily
accessible via your web browser.
Basic Features
• Powerful high-speed video protocol processor
• High-sensivity 1/4" CMOS sensor
• 300K Pixels
• IR night vision (Range: 3-5m)
• Opmised MJPEG video compression for transmission
• Mul-level users management and passwords denion
• Embedded Web Server for users to visit via web browser
• Support wireless network (Wi-Fi/802.11/b/g) mobile
• Supporng Dynamic IP (DDNS) and UPnP LAN
• Alarm for moon detecon
• Support one-way (I/O) alarm connecon
• Image snapshot
• Mulple network protocols incl: HTTP/TCP/IP/UDP/SMTP/DDNS/DHCP/FTP
• Remote system update

6
WatchBot Home Security Camera - User Guide
DCPower
Wi-Fi Antenna
LEDs
I/O Connector
LightSensor
Lens(turntofocus)
Microphone
MiniJackforSpeaker
Pan/Tiltmoon
RJ45NetworkPort
Warning: Do not forcibly move the camera pan/lt moon manually. This is likely to result in
damage to internal components and will void your warranty.

7
WatchBot Home Security Camera - User Guide
1 QuickSetupandOperaon
1.1 The WatchBot IP camera is a capable and technical piece of hardware. To get you up
and running quickly with your device, please follow this Quick Setup Guide.
For more advanced setup opons and troubleshoong, please consult the AdvancedGuideon
page16andFAQsonpage29ofthisguide.
1.2 Connectcameracomponents
On removing your camera from the box, there are three essenal components you need to
connect together:
• Connect your Wi-Fi Antenna to the rear of the camera
• Connect the camera to a spare port on your network router using the network cable
provided
• Connect the power supply

8
WatchBot Home Security Camera - User Guide
1.3 InstalltheWatchBotCameraToolSoware
Insert the supplied Soware CD into your CD-ROM drive. It should auto-run, but if it
does not, open up ‘Computer’ and double-click on the CD-ROM drive icon and select
‘WatchBotCamSetup.exe’.
Choose ‘Install WatchBotCam Tool’ and follow the on-screen instrucons.
When complete, pleaseRestartyourcomputer.

9
WatchBot Home Security Camera - User Guide
1.4 RuntheWatchBotCameraToolSoware
The WatchBot Camera Tool icon will have appeared on your Computer Desktop.
Double-click the icon to run the camera soware.
A dialogue window will appear similar to the one shown below. You should see your camera
listed and it’s assigned Local IP (Internet Protocol) Address. This is usually takes the form of
192.168.0.X or 192.168.1.X. If no camera(s) are listed, or you see any other error message,
pleasegotoSecon5-FAQs,formoredetails.
Note: The assigned IP Address will change each me the WatchBot Camera Tool is
launched or if the camera is rebooted.
Note: Right-clicking on the entry above will give access to a context menu for funcons
described in detail later in this manual.
1.5 SengupyourWatchBotcameraonyourLocalArea
  Network(LAN)
Note: This Quick Setup Guide assumes you are using Microso Internet
Explorer web browser. Other browsers will work for viewing the camera’s
live video feed, however less features will be available. Please upgrade
your browser to the latest version of Internet Explorer available to you.
Using another browser? Please see Secon 4.
Before your camera can be accessed via the Internet, it needs to be setup on your LAN.
Double-click on the camera lisng as shown above in the WatchBot Camera Tool soware.
Aer a short me, a Log In window will appear as shown overleaf.
As we have not yet set up any extra Administrators or Users, log in with admin/nopassword.

10
WatchBot Home Security Camera - User Guide
A Sign In screen will appear as shown below. Click the ‘Sign-In’ buon in the top secon
labelled ‘AcveX IE Browser’. You will then be logged into the camera control interface.
1.5.1 ImportantInformaonaboutMicrosoAcveXControls
AcveX controls are small programs, somemes called add-ons, that are used on the Internet.
They can enhance your browsing experience by allowing interacve content or they can help
with tasks such as installing security updates. Some websites require you to install AcveX
controls to see the site or perform certain tasks on it. When you visit such a site, Internet
Explorer asks if you want to install the AcveX control. Some WatchBot camera funcons such
as recording and audio require AcveX controls to be enabled. If you experience any issues
with enabling AcveX on your computer, please visit hp://windows.microso.com/en-GB/
windows-vista/Why-does-Internet-Explorer-block-some-AcveX-controls for more assistance.
AcveX is not required when using other browsers such as Firefox, Chrome or Safari, however
features are much more limited. (Seesecon4fordetails).
Once AcveX is correctly congured within Internet Explorer, you will see the live video feed
from your WatchBot camera and a green light will appear next to ‘1’ under ‘Device Status’.
The camera is now available to your local network. If required, focus can be manually adjusted
by gently turning the camera’s focal lens.

11
WatchBot Home Security Camera - User Guide
1.6 OperatorControls-Basiccameraoperaon
Your WatchBot camera features pan/lt (P/T) controls, providing a wide viewing angle.
Access to these controls appears on the right of the video feed.
1.6.1 Pan/Tilt(P/T)Controls
Click on any of the direconal arrow buons and the camera will respond and move in that
direcon. To centre the camera, click on the red centre icon. The device will then perform a
full vercal and horizontal patrol before re-centering it’s view.
1.6.2 Patrol
Clicking the horizontal or vercal patrol buons will tell the camera to make a patrol in that
direcon. Click the pause buon to pause the patrol.
1.6.3 I/OSwitchOn/O
Toggles the I/O Switch Output On and O. I/OconnecvityisdescribedinSecon3.6.5.
1.6.4 Flippingthefeedimage
If required, the video feed image can be horizontally or vercally ipped by checking these
boxes:
PatrolBuons
Pan/Tilt Controls
I/OSwitchOn/O

12
WatchBot Home Security Camera - User Guide
1.6.5 Pre-PosioningBuons
First, move the camera to a certain posion and press to save the posion. Then, move to
another posion and press the buon. The camera will go back to the posion you just saved.
1.6.6 ScreenResoluon/Mode
The video feed screen resoluon can be toggled between 320 x 240 pixels (low-res) and
640 x 480 pixels (high-res), and the Mode (Refresh Rate) can be set to either 50Hz, 60Hz or
‘Outdoor’ for a icker-free video display.
1.6.7 BrightnessandContrast
Brightness and Contrast can be adjusted to suit.
1.6.8 Defaultsengs
Click ‘Default all’ to reset all preferences to their default sengs.
1.7 VisitorControls,Recordingvideoandaudio
Via Internet Explorer, the WatchBot camera features comprehensive monitoring and recording of
video images and sound. To access these features, click the ‘For Visitor’ tab on the right.

13
WatchBot Home Security Camera - User Guide
1.7.1 Mul-View
Up to nine WatchBot cameras can be connected and monitored simultaneously via a
split-screen. Click the mul-view icons to monitor up to 1, 4, or 9 cameras.
1.7.2 AddTimestamp
Check this box to add a mestamp to your video footage for accurate me-tracking.
1.7.3 On-ScreenDisplay(OSD)
Choose from a range of colours to display the camera name, date and me on screen and
recorded footage.
1.7.4 AudioBuer
If experiencing slow internet speeds, set the Audio Buer to a higher number. This will
however result in more of a sound delay.
1.7.5 LivefeedOn/OandSnapshot
Click the ‘PLAY ARROW’ icon to monitor the live video feed, click the ‘PAUSE’ icon to turn o
the live video feed and click the ‘Camera’ icon to take a sll snapshot of the current view.
1.7.6 Recordingvideoandaudio
Simultaneous recording of up to nine WatchBot cameras can be performed using the record
funcons. Each camera is listed from 1 - 9 and has it’s own set of icons:
i ii iii
i. Toggle recording of audio on/o.
ii. Toggle voice interacon on/o. (Don’t forget to connect a speaker via the mini jack).
iii. Toggle Recording of video on/o. (On clicking this buon, you will be asked where you
wish to save the subsequently recorded .AVI video le).
1.7.7 MoonSensor,AlarmandEmailAlert
Your WatchBot camera comes complete with comprehensive moon detecon, alarm and
email alert funcons. PleaseseeSecon3.6fordetailsofthesefeatures.

14
WatchBot Home Security Camera - User Guide
2 Sengupyourcameraforaccessvia
  theInternet
Up to now, we have covered seng up your WatchBot camera on your local network (LAN).
Here, we will look at accessing the camera from the Internet, so that wherever you are, you
can access the live video feed from your camera.
2.1 SengupNetworkSengs
Your WatchBot camera needs an IP (Internet Protocol) address in order to appear on your local
network and subsequently to be accessed via the Internet.
2.1.1 Click‘Administrator’tabonright,thengoto‘BasicNetworkSengs’
This page allows you to either manually enter the network details (these would be available
from your Internet Service Provider), or in most cases, obtain these details from the DHCP
(Dynamic Host Conguraon Protocol) server.
Note: If in doubt, try DHCP rst, as in many cases this will work by assigning your camera
an IP address automacally. Please contact your Internet Service Provider if you are sll
experiencing any diculty.
Once DHCP box is checked:
2.1.2 Oncethisisset,thengoto‘UPnPSengs’
Check the box next to ‘Use UPnP to Map Port’, then click ‘Submit’. On compleng these steps,
your camera is now available to be accessed over the Internet.

15
WatchBot Home Security Camera - User Guide
2.2 Visitthewebpageassignedtoyourcamera
Now visit the web page listed on the scker on the base of your camera under ‘DDNS
Hostname’. It will resemble wbot[XXXXX].watch-bot.net and login with the default admin/no
password. (To set up more users, please see Secon 3.1.4).
Aer logging in, click ‘Sign-In’ under ‘AcveX Mode for IE Browser’, you will be logged in to the
camera viewing and control interface.
Note: Please see technical note in Secon 1.5.1 regarding Microso AcveX controls
if experiencing any diculty.
Formanymorefeatures,pleaseseeSecon3-AdvancedSetupGuide.

16
WatchBot Home Security Camera - User Guide
3 AdvancedSetupGuide
Your WatchBot camera contains many innovave features, making it a versale and complete
home security system, including Moon detecon, Alarm, Email and Live Messenger (MSN)
funcons. This advanced guide will take you through the more technical capabilies of the device.
3.1 AdministratorSengs
Click the ‘ADMINISTRATOR’ tab on the right of the interface to access these sengs.
3.1.1DeviceInfo
See screenshot above. This provides an overview of the Camera Device unique ID, Firmware
version, Interface version, Alarm Status, assigned Name Server (DNS) sengs, Universal Plug
and Play (UPnP) sengs and MSN status.
3.1.2 AliasSengs
This screen allows you to set the name of each camera on your network for easy reference.
For example, Car port, Kitchen, Living Room.

17
WatchBot Home Security Camera - User Guide
3.1.3 DateandTimeSengs
Here you can set the device mezone and synchronise the me with any one of a number of
Network Time (NTP) Servers around the world, or your own Computer me sengs.
3.1.4 UserSengs
Here you can set up User Accounts and Access Levels for yourself and anyone else who will
need access to the camera. They are as follows:
Administrator: Access to all camera funcons and administrator sengs.
Operator: Access to all viewing, camera control and recording funcons,
but not the administrator sengs.
Visitor: Access to viewing and recording funcons, but no access to camera
controls or administrator sengs.
Simply enter the username(s) and password(s) and access level(s) you wish to assign and click
‘Submit’. These are then used as logins.
(Tip: You may wish to make a note of these elsewhere).

18
WatchBot Home Security Camera - User Guide
3.1.5 Mul-DeviceSengs
This screen provides an overview of your connected cameras and their IP addresses. It also
allows eding of the IP addresses, providing the ability to access a wider network of WatchBot
cameras anywhere in the world, via the Internet. Up to nine devices can be added, four of
which can be online at any one me
AddcameraswithintheLocalNetwork(LAN)
Here, you can see all devices searched in LAN. The 1st Device is your rst camera. You can add
more cameras in the LAN for monitoring. The Web soware supports up to 4 Cameras online
simultaneously. Click ‘The 2nd Device’ and Double click the item in the ‘Device List in LAN’.
‘Host’ and ‘Hp Port’ will ll in automacally. Enter the correct username and password then
click ‘add’. Add more cameras in the same way.
AddcamerasviatheInternet
Firstly, make sure the camera added can access the Internet with the IP address or DDNS
domain. For example: hp://219.133.200.165: 81 or hp://wbot[XXXXX].watch-bot.net. Enter
these details in ‘Host’ along with the ‘Alias’ and ‘Hp Port’ seng. Enter the correct username
and password then click ‘add’. Add more cameras in the same way.

19
WatchBot Home Security Camera - User Guide
3.1.6 BasicNetworkSengs
Your WatchBot camera needs an IP address in order to appear on your local network and
subsequently to be accessed via the Internet. This page allows you to either manually enter
the network details (these would be available from your Internet Service Provider), or in most
cases, obtain these details from the DHCP (Dynamic Host Conguraon Protocol) server.
‘Hp Port’ can usually be le as the default.
Note: If in doubt, try DHCP rst, as in many cases this will work by assigning your
camera an IP address automacally.
3.1.7 WirelessLANSengs
Your WatchBot camera can funcon wirelessly on your local network, negang the need for a
network cable to be aached to the device.
By adding your wi- sengs here, your camera will remember them and funcon wirelessly.
3.1.7.1UsingyourWatchBotcamerawirelessly
First, ensure your camera has mains power and that your Wi-Fi antenna is aached to your
camera. Also ensure your Wireless LAN is using WEPencrypon. (See note overleaf).
Click ‘Scan’ to search for your wireless network, then complete the details on the page. If the
scan does not nd your network, your SSID can be obtained from your router page. If you have
problems, please consult your router manual and/or contact your Service Provider

20
WatchBot Home Security Camera - User Guide
Important Note about Wi-Fi networks! At the moment, the WatchBot camera
only supports wireless networks secured with WEP encrypon. WPA/WPA2 encrypon
is currently not supported. Please set ‘Encrypon’ to WEP and ensure your network
router sengs are set the same.
Click Submit to save the sengs. The camera will reboot.
Unplugthenetworkcable
Once the sengs above have been saved and the camera has rebooted, unplug the network
cable from the camera, then unplug the power cable.
Re-aach the power cable and wait approximately 30 seconds to 1 minute for the device to
appear on the wireless LAN. (You can test this by aempng to access your camera interface
via Internet Explorer).
Your WatchBot camera is now funconing wirelessly and will only need it’s power cable
aached in order to operate.