Waterworks 100518 Instruction sheet
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM PAGE 1 OF 4 | UPDATED ON 11.05.2020
STYLE No. 100518
Lucerne Metal Two Leg Single Washstand
36 15/16” X 22 7/8” X 29 3/8”
INSTALLATION GUIDELINES
TECHNICAL DETAILS
DETAIL SPECIFICATION
ADJUSTABLE LEVERS / FEET YES
DIAMETER OF LEGS 2-15/16” [75mm]
LEG MATERIAL NICKEL / BRASS
PRIMARY MATERIAL NICKEL / BRASS
WEIGHT 66 lbs [30kg]
WARNING: Some parts are large and heavy, the assistance of
one or more person is highly recommended in order to prevent
personal injury and/or damage to the product during the
assembly process.
IMPORTANT
¾To ensure this product is installed properly, you must read and follow
these guidelines.
¾The owner/user of this product must keep this information for future
reference.
¾Install adequate blocking or position over a stud to properly secure
the fixture.
¾Inspect this product, upon receiving, to ensure it is the correct model
and you have all parts required for proper installation.
¾Slab top, fittings, and lavatory sold separately.
¾Take all necessary precautions to ensure that this product is protected
during installation.
¾This product is extremely heavy. It is STRONGLY recommended that
2 or more persons install this product.
¾Ensure the floor is level and the weight of this product will be
adequately supported.
¾The use of certain plumber’s putty may stain stone or tile surfaces.
¾If further assistance is required, please contact Product Support at
1-800-927-2120 Monday through Friday, 8 am -6 pm EST.
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM PAGE 2 OF 4 | UPDATED ON 11.05.2020
STYLE No. 100518
Lucerne Metal Two Leg Single Washstand
36 15/16” X 22 7/8” X 29 3/8”
INSTALLATION GUIDELINES
HARDWARE LIST
1SOCKET FLAT HEAD SCREW
6mm x10
2FINISHED PHILLIPS SCREW
40mm x4
3FINISHED ROUND HEAD PHILLIPS
SCREW 60mm x6
4ALLEN WRENCH
4mm x1
5OPEN END WRENCH
| RING SPANNER x1
FAUCET (SOLD SEPARATELY)
SLAB TOP (SOLD SEPARATELY)
SINK (SOLD SEPARATELY)
WASHSTAND SINK FRAME
WASHSTAND LEG
GLASS SHELF FRAME
GLASS SHELF
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM PAGE 3 OF 4 | UPDATED ON 11.05.2020
STYLE No. 100518
Lucerne Metal Two Leg Single Washstand
36 15/16” X 22 7/8” X 29 3/8”
INSTALLATION GUIDELINES
3. From your prepared location, pre-set the assembled
WASHSTAND against the wall, examine the alignment of
the WASHSTAND to see if leveling is necessary. If needed,
slightly tilt the WASHSTAND and turn the LEVELERS
clockwise to raise the FIXTURE and counter-clockwise
to lower it. Adjust all LEVELERS until the correct level is
achieved.
2. Set the WASHSTAND SINK FRAME on top of the LEGS
and secure this with the SOCKET FLAT HEAD SCREW.
Tighten all the SCREWS to a snug fit.
NOTE: The SINK FRAME has 2 CORNER BRACKETS with
holes for the SCREWS to pass through which correspond
to the threaded holes on the top of each LEG.
1. In preparation for assembly, place the WASHSTAND
LEGS on a non-abrasive working bench with the
LOCATOR of the LEG facing upward. Fit both ends of the
GLASS SHELF FRAME into the LOCATOR of each LEG
and secure the FRAME using the SOCKET FLAT HEAD
SCREW provided.
NOTE: Both ends of the SHELF FRAME have holes for
the SCREWS to pass through which correspond to the
threaded holes on the LOCATOR on each LEG.
WASHSTAND LEG
LOCATOR
GLASS
SHELF
FRAME
SOCKET FLAT HEAD
SCREW X 2 / LEG
SOCKET FLAT HEAD
SCREW X3 / LEG
CORNER BRACKET
WASHSTAND SINK
FRAME
LEVELER
LOWER RAISE
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM PAGE 4 OF 4 | UPDATED ON 11.05.2020
STYLE No. 100518
Lucerne Metal Two Leg Single Washstand
36 15/16” X 22 7/8” X 29 3/8”
OPEN END
WRENCH
INSTALLATION GUIDELINES
6. It is recommended to install the FAUCET, and SINK (sold
separately) to the SLAB TOP before setting it into the
FRAME. The GLASS SHELF should be installed after
plumbing is complete.
NOTE: Plumbing Installation must be done by a qualified
plumber and in accordance with all applicable plumbing
and building codes in force in your area.
5. Secure the WASHSTAND SINK FRAME and GLASS
SHELF FRAME to the wall with the FINISHED ROUND
HEAD PHILLIPS SCREWS provided.
NOTE: For safe mounting, it is important to use the proper
hardware for your wall type. The included hardware is for
stud mounting only. If the METAL BRACKET cannot be
secured to a wall stud because of inappropriate spacing
and/or because you have a different wall type (e.g.,
plaster, concrete, brick, etc..) please consult your local
hardware store for fastener advice.
4. Slightly loosen the metal BRACKETS attached to the
back of the WASHSTAND SINK FRAME. At your desired
location, bring the WASHSTAND against the wall and
secure the WASHSTAND BRACKETS using the FINISHED
PHILLIPS SCREWS provided. After fastening the
BRACKETS on the wall, re-tighten the metal BRACKETS
with the OPEN END WRENCH or RING SPANNER
provided.
WASHSTAND SINK
FRAME
WASHSTAND SINK
FRAME
GLASS SHELF
FRAME
GLASS SHELF
FAUCET
(SOLD SEPARATELY)
SINK
(SOLD SEPARATELY)
SLAB TOP
(SOLD
SEPARATELY)
BRACKET
FINISHED PHILLIPS
SCREW 40mm X4
FINISHED
PHILLIPS
SCREW ROUND
HEAD 60mm
X6
