WAVESYS IP-10201LDI User manual
Fixed Mini Dome Camera
2M HD IP
G Ver. 1.2 / 2021.03
User’s Manual_Install Part
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
Contents
INTRODUCTION
Product & Accessories
Part Name
03
06
07
INSTALLATION
Disassemble the Camera
Cabling
08
09
10
12
13
SPECIFICATION
Dimension14
2
POWER
1. Use only standardized adapters wrien in the manual.
Incorrect cower source can cre,
electric shock, or failure.
2. If there is smoke or a strange smell from the power
source, disconnect the power immediately and contact
the service center orpurchasingoce. If you conto
use it as it is, it can cre and electric shock.
3. Disconnect the power plug from the outlet before
cto the power terminal block.
INSTALLATION
1. Install it according to the temperature and humidity environment
suitable for the product speccatherwise, it can cause
re and electric shock.
2. Thunder and lightning can cause problems with the camera.
When installing, be careful to minimize damage caused by
lightningsuch as grounding.
3. Do not place cve materials (drivers, coins, metal
sks, etc.) and water-containers on the camera. It
causes injuries caused bre, electric shock, and falling.
4. If you want to move the installed product, turn o
power and move it or reinstrwise, it can cause
re and electric shock.
5. Do notinstall itin places where there is alotof moisture,
dust, soot, etc. It care and electric shock
.
6. Avoid places where direct sunlight comes in or where heat
comes out, such as heagappliances. It causere and electric
shock.
CLEANING
1. Do not spray water directly on each part of the product
when cleaning. It cre and electric shock.
POWER
1. Use the power line aergitrmly to the power connec
terminal. Incomplete conneccan causere.
2. Do not extend the adapter output cable. If you need to
install the power cable extension, please contact the
service center.
3. Use insulated power for PoE connected external power.
INSTALLATION
1. It is recommended not to touch the lens when installing
the product as the factory ships with a focus adjustment
completed during the manufacturing comple
2. Avoid installing cameras facing bright lights like sunlight.
Causes damage to the image sensor.
3. Make sure it safe and securely when installing camera on
the wall or ceilling. This can cause injury by the fall.
4. Do not ccameras to one adapter. Excess
capacity causes abnormal heare.
5. Wear protve gloves when installing/uninstalling the
camera. This causes burns caused by high temperature
on the surface of the product.
6. Don't drop or shock the product. Please stay away from
places where vibraevere or magnet types are
present.
7. Install it in a well-venated place. This can cre and
failure.
CLEANING
1. Wipe the contaminated surfry
cloth or wery cloth to prevent water from
owing, then wipe the contaminated area.
Safety Instruction
Theseinstrucare intended to ensure that the user can use the product correctly to avoid danger orproperty loss.
If the product is notfuncgproperly ordamaged, contact the service center orpurchasingoce.
Warnings
Serious injury or death may be caused
if any of these warnings are neglected.
Cautions
Injury or equipment damage may be caused
if any of these cautions are eglected.
3
Installarec
1. The baery (baery pack or equipped baery) must not be exposed to excessive heat such as sunlighre, etc.
2. Do not disassemble the camera at your discre
3. If you forcefully install the product with excessive forcan damage the camera.
4. Do notpunch orshake the camera and be careful not to damage the camera with careless storage or malfuncn.
5. Be careful not to install the camera in a rainy or humid place, and do not leave it in a wet place.
6. Installing or using the product in water can cause serious product failure.
7. Do not install the product if there is chemical or vapor in the place where the product is installed, or if it can be generated.
8. Be careful not to get chemicals on the surface of the product when installing the product. Chemical solvents such as cleaning
agents and adhesive components can cause fatal damage to the surface of the product.
9. Do not install it near the kitchen or cooking table as edible oil such as soybean oil can also cause product damage and
deformacan cause product damage.
10. Be careful not to get foreign substances on the Micro SD card terminal. If there is any foreign subst
cloth.
11. Data will not be saved at the end of the life of the Micro SD card. In this case, purchase a new Micro SD card.
12. Moisture may occur in the glass of the camera when the new product box is opened (or when the pr
The generated moisture is removed by a Gore vent aached to the camera within hours of the power c
13. For products enclosed with a desiccant or card-type absorbent, please install it according to the manual.
14.
or sold with the apparatus.
15.
4
Disposal of Old Appliances
1. The symbol marked in the product, will follow and covered by the Europe Dirve 2002/95/EC.
2. All electornic disposal of waste is dierenct by the government or locally, so so it need to check.
3. The correct disposal of your old appliance will help prevent potengave consequences for
the environment and human health.
4. For more detailed informayour old appliance, please contact your city o
waste disposal service or the shop where you purchased the product.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protgainst harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the insay cause
harmful interference to radio communicarant in a residenrea is likely to cause harmful interference in which case the user
will be required to correct the interferenece at his own expense.
5
Product & Accessories
Introduc
Camera
Cables
Template Sheet
for Installing by Bolt & Nut
Mount Bolt & Nut
Screw &
Torx Wrench Waterproof cap & Gasket
Quick Manual
6
Part Name
Introduc
Dome Cover
IR LED
Lens
Gimbal
DC Power Jack
RJ-45 Connector
IR Switch
Waterproof cap
7
Disassemble the camera
Installa
Before installing your camera, you have to read the following cau�ons.
valuable things under the place, move them away.
Detach the dome cover by torx wrench provided from
Match the one screw hole on the dome cover and
1
Reset to the Factory Default
Press the reset buon for 5 seconds to return the setup
to the factory default.
Warning:
data. If needed, please, make a note for further installaon.
The camera has a manual IR switch, located under
the camera’s lens. You can use this switch to
2
8
7
1
2
3
4
Disassemble the camera’ for details.
Using the template sheet, make the cabling hole on
the wall/ceiling.
Connect the network cable and power cable
details.
on the ceiling.
stopper screw.
5
6
ab
c
Put the Lan cable into (a), then (b) will be assembled to (a)
without making any space.
Installa
Installa
3
2
6
5
4
3
3
3
2
Template Sheet
7
9
Installa
InstallaUsing Mount Bolt & Nut
Template Sheet 1
Disassemble the camera’ for details.
Using the template sheet, make the cabling holes on
the ceiling panel.
3
2
10
Installa
InstallaUsing Mount Bolt & Nut
5
mount bolts on the ceiling panel.
4
7
8
6
stopper screw.
11
Installa
12
Cabling
Installa
Power
Two Op�ons
Use a PoE-enabled switch to connect data and power through a single cable and begin viewing and recording images instantly.
A non-PoE switch will require an adaptor for power transmission.
Ethernet cableEthernet cable
2. Using a Non-PoE Switch
If a PoE-enabled switch is not used, use a power adaptor
for power transmission and non-PoE switch for data
transmission.
without a PoE-enabled Switch.
1. Using a PoE-Enabled Switch
The Camera is PoE-compliant, allowing transmission of
power and data via a single Ethernet cable.
power, record, or control t
below to connect the camera to a PoE-enabled switch using
an Ethernet cable.
13
Unit: mm
Dimension
ø105
32.5
28.5
14
Table of contents
