Waydoo Flyer ONE-RC User manual

Quick Start Guide
2020.11V1.0
Waydoo Technical Support
This guide may be updated without notice.
Check the ocial Waydoo website for the latest version.
www.waydootech.com
Model: Waydoo Flyer ONE-RC

Content
2
3
3
8
9
12
13
Disclaimer
Parts
Assembly Steps
Safety Guidelines
Troubleshooting
Maintenance
Waydoo Flyer ONE
Waydoo Flyer ONE Quick Start Guide
Minors under the age of 18 are not suggested to use this product. A
safety summary as part of the operating safety knowledge is included. Please read the
entire content of the disclaimer and safety operating instructions carefully. After reading
the entire user manual, familiarize yourself with the functions of the product before
proceeding. This product can cause serious injury to oneself or others, or cause product
damage and property loss. This product can only be used safely with instructions clearly in
mind, and it requires some basic common sense before operation. Do not use parts that
are not provided or recommended by Waydoo, and strictly follow Waydoo's instructions to
install and use the product. This guide contains instructions on safety, operation, and main-
tenance. Make sure to carefully read all instructions and warnings in the quick start guide
before assembly, setup, and use.
Disclaimer
Please read this manual and related warnings carefully before use. This product concerns water
sports equipment. Using this product has inherent risks that may cause serious injury or even
death. Users who use this product must understand and accept the inherent risks of using this
product. Misuse of this product may cause product damage or personal injury. As a continuous
eort of product development, Waydoo reserves the right to change the components, specica-
tions or other aspects of this product without prior notice. For more information, please visit:
www.waydootech.com.
EN
1 2
All rights reserved by WaydooAll rights reserved by Waydoo

Waydoo Flyer ONE Quick Start Guide Waydoo Flyer ONE Quick Start Guide
ENEN
The Waydoo Flyer ONE has been ingeniously built to allow more people to experience the thrill of
water sports. The overall weight of the product is 16 kg without battery and 28 kg with battery,
with an overall size of 1680×700×1050 mm.
The Jet ONE Controller should be paired with the PowerFlight Cell for Bluetooth connection. The
Jet ONE Controller is ergonimcally designed and adopts an OLED display interface. The display
shows the speed and the power level of the PowerFlight Cell and the Jet ONE Controller.
Waydoo Flyer ONE
Founded in 2018, Shenzhen Waydoo Intelligence Technology Co., Ltd. is a company that invests
and manufactures intelligence hardware for water sports enthusiasts.
Feature Highlights
Power 6000W Operating Time
55 – 85 min
Charging Time
2 h
Maximum Speed
42 km/h
Introduction
Jet ONE Controller Display
Parts
Jet ONE Controller
1. Power Button
2. Display
3. Magnetic Charging Port
4. "+” Speed Gear
5. "-" Speed Gear
6. Trigger
1. Jet ONE Controller Power Level
2. Speed 3. Waydoo Flyer ONE Power Level
4. Bluetooth 5. Speed Gear
6
4
5
1
2
3
The Jet ONE Controller displays power, Bluetooth
connection and ight speed. It oers 24 speed gears.
Charge the Jet ONE Controller
1. This product uses magnetic charging to reduce
friction between terminals.
2. When the charging cable connector is closed to the
charging port of the Jet ONE Controller, the charging
connector automatically connects to charge. The
charging time is 3 hours.
1
4
5
2
3
1. When the Jet ONE Controller is not connected, the
Bluetooth icon on the display continues to ash until it
is connected.
2. The Jet ONE Controller oers 24 speed gear options.
In speed limit mode, speed options can be limited to
10 gears and the highest gear can be adjusted.
3. The number on the left of the speed level shows the
current gear.
Remarks:
1. When the battery level of the Jet ONE Controller is
lower than 20%, a low battery warning prompt
appears. Make sure to charge in time.
2. When the Jet ONE Controller is in standby for more
than 8 seconds, it will switch to the screen with the
lock icon. Press and hold ”-“ for 1 second to unlock.
Remarks:
3 4
All rights reserved by WaydooAll rights reserved by Waydoo

Fast Charger
Adopting an aluminium alloy diecasting , the Fast
Charger has an input voltage of 90-260 V, output
voltage of 58.6-59 V, charging current of 16-18 A, and
a protection level of IPX6.
1. Integrated Line 2. Power Cord
3. Indicator Light
Battery
Status Indicators
100%25%
Fault Indicator
Output Indicator
Waydoo Flyer ONE Quick Start Guide Waydoo Flyer ONE Quick Start Guide
ENEN
1. Bluetooth Button
2. Battery Status Display
3. Rotary Lock
4. Power Button
5. Integrated Port
Short press “+” and “-” simultaneously when the Jet
ONE Controller is powered on to enter Settings.
Scroll through the menu by pressing the“+” or “-” and
press the Power Button to conrm.
After entering the sub-menu, use "+" or "-" to scroll
and press the Power Button to select the Mode. Press
"+" or "-" to switch and press the Power Button to
conrm. The highest gear can be adjusted in speed
limit mode.
Finally press“+”or“-“ to scroll to the return option, and
press the Power Button to conrm until you exit the
Settings. Refer to the Units and change operation as
follows:
For languages, refer to the Language and change
operation work as the following mode operation.
Switching Working Mode:
Normal Mode
PowerFlight Cell Charging Status Description
The PowerFlight Cell can be embedded in the board
and has an average battery life of 55-85 minutes. The
battery has a capacity of 32500mAh and the voltage is
14S/58.8V. Additionally, the built-in AL system tracks
the battery status, allowing for a safer user experience.
(Front) (Back)
5
1
2
3
4
Units
Units
return
kph
Units
Units
return
mph
5 6
All rights reserved by WaydooAll rights reserved by Waydoo
Speed Limit Mode
Mode
speed limit
return
off
Mode
speed limit
top gear
return
on
24
1
2
3
LED Status
Steady blue light Standby
Flashing blue light Connecting
Charging
Fully charged
Flashing green light
Full green light
1. Connect the charger’ s integrated line to the battery
integrated port.
2. The charger power indicator shows a steady blue
light indicating standby mode; then short press the
linking switch on the smart battery, and the indicator
will change from a steady blue light to a ashing blue
light, waiting for communication; then the ashing
blue light turns to ashing green, indicating that it
enters the charging mode.
Note: Fully charge the PowerFlight Cell when using for
the rst time. Make sure to use the standard charger.
Menu
Mode
Units
Language
return
Language
Language
return
EN
语言切换
语言切换
返回
中文
Menu
Mode
Units
Language
return
Menu
Mode
Units
Language
return
Charge the PowerFlight Cell

Travel Pack and Toolkit
Travel Pack (Board) x 1
Travel Pack (Gears) x 1
EPP Board x 1
Power Assembly & Wing Set x 1
PowerFlight Cell x 1
Jet ONE Controller x 1
Controller Charging Cable x 1
Fast Charger x 1
M6*24 Board Fixing Bolt x 2
M6*15 Board Fixing Bolt x 2
Mast Fixing Bolt x 2
4mm Hexagon Wrench x 1
1. Integrated Port 2. Bolt Fixing Hole
3. Main Wing 4. Mast Head 5. Support Rod 6.
Propeller Guard 7. Tail Wing
4
7
5
6
1
2
3
3. To prepare to pair, short press once and long press
the Bluetooth button on the PowerFlight Cell for 2
seconds. After the PowerFlight Cell is powered on,
nish Bluetooth pairing in one minute, otherwise the
PowerFlight Cell should be rebooted.
4. For Bluetooth pairing, simultaneously press and
hold the Power Button of the Jet ONE Controller and
speed gear “-” button. When the Bluetooth icon
disappears, it means the pairing is successful. If the
devices have been paired before, they will connect
auomatically and Step 3&4 can be skipped.
1. Press the Power Button on the Jet ONE Controller for
5 seconds. Power on the Jet ONE Controller.
2. Short press once and long press and hold the Power
Button on the PowerFlight Cell. Power on the Power-
Flight Cell.
1. Face the battery compartment upward and reset
both Rotary Locks.
2. Insert the PowerFlight Cell into the battery compart-
ment. Turn both Rotary Locks 180-degree to securely
lock the battery in place.
4. Connecting the Jet ONE Controller
Assembly Steps
1. Turn the EPP Board over to insert the Mast & Power
Assembly vertically into the board installation port.
2. After inserting the mast head into the hub to make
sure it ts, x with L-shaped bolts and tighten.
1. Assembling the Mast
1. Attach the Tail Wing on the tail-end mounting hub
and tighten the two M6*15 bolts clockwise with the
4mm Hexagon Wrench.
2. Assembling the Wings
3. Installing the PowerFlight Cell
2. Put the Main Wing on the front-end mounting hub
and tighten the two M6*24 bolts clockwise with the
4mm Hexagon Wrench.
3. Flip over the EPP Board and proceed to the
next step.
Waydoo Flyer ONE Quick Start Guide Waydoo Flyer ONE Quick Start Guide
ENEN
7 8
All rights reserved by WaydooAll rights reserved by Waydoo
1. Side Handle
2. Rotary Lock
3. PowerFlight Cell
EPP Board
The EPP Board acts as the main body and core of the
efoil, with a large area of soft cushion that makes for a
better user experience. High quality composite materi-
als and aluminum alloy are used to reinforce the
board, while the streamlined design optimizes the
overall performance of the product.
123
Power Assembly & Wing Set
The Power Assembly & Wing Set has a built-in control
system, and uses the EPP Board to complete the
system connection. The ESC and motor are located
underwater and boost eective heat dissipation. With
an overall structure that is easy to assemble and
disassemble, the Power Assembly & Wing Set is quick
to start using.
3. When the indictor light on the Fast Charger changes
from ashing green to full green it means that the
PowerFlight Cell is fully charged. The PowerFlight Cell
usually takes 2 hours to charge. When the red light
ashes on the Fast Charger, it means the device is
malfunctioning. Stop charging immediately if this
occurs.

1. Before use, make sure that the propeller and protective cover are not damaged or cracked, and carefully remove
any sand or debris.
1. Do not remove the propeller guard.
2. Do not attempt to x or touch the propeller in the water.
3. When the system is powered on, keep the propeller away from your body, ngers, and toes.
4. The rotating propeller may cause serious, or even life-threatening, injury. Treat with caution.
Motor
Support Rod
PowerFlight Cell
1. The use of the product requires a water depth of at least 1.2 meters. Be careful of gravel, plants, or wild animals
in the water.
2. When using the product, pay attention to the surrounding environment, stay away from the shore, and keep a
safe distance from ships and others.
1. When used in water, any contact with the wings and the Support Rod may cause serious, or even life-threaten-
ing, injury. Treat with caution.
Safety Guidelines
1. Safety Summary
1. Refer to the user manual and watch the ocial instructional video to learn how to use this product.
2. This product can only be used on water. Take safety measures when using this product and wear a life jacket
and safety helmet.
3. The use of this product requires a water depth of at least 1.2 meters. Be aware of gravel, plants, or wild animals
in the water.
4. When using the product, pay attention to the surrounding environment, stay away from the shore, and keep a
safe distance from ships and other people.
5. Do not use this product in waters where there are swimmers or divers.
6. Do not use this product in waters with oating objects, obstacles, or many wild animals and plants.
7. Do not use damaged or malfunctioning products.
8. Do not place the product directly on the roof of the car for transportation. Otherwise, the product may slide o
and cause serious damage.
9. Do not use this product before fully understanding the operation steps and inherent risks of the product.
10. Do not allow others to use this product unless they fully understand how to use the product correctly.
11. Do not remove the propeller guard.
12. Do not attempt to x or touch the propeller in the water.
13. Do not remove the battery when the product is in the water.
14. When the system is powered on, keep the propeller away from your body, ngers, and toes. The rotating
propeller may cause serious, or even life-threatening, injury. Treat with caution.
15. When used in the water, any contact with the powertrain, front wing or tail wing may cause serious, or even
life-threatening, injury. Treat with caution.
16. Do not use this product in bad weather. Pay attention to changes in weather when using this product.
17. Always use this product steadily and safely. Do not perform dangerous operations such as overspeeding or
sharp turns.
18. During the use of product, the deadweight of the product shall not exceed 100kg.
2. Make sure that the propeller and protective cover are not damaged or cracked, and carefully remove any sand
or debris residue.
3. Install the PowerFlight Cell in the designated location.
4. Make sure the PowerFlight Cell is installed rmly and the lock is tightened in place.
5. Make sure the product is free of damage and is working properly before use.
2. Know Before Use
Before using this product, check the product to ensure that the waterproof components (such as the Jet ONE
Controller, the PowerFlight Cell, and the mast head) are not damaged, the power system and control system work
normally, the battery power is sucient, and the bolts of each component have been tightened. Do not use
damaged products.
1. Check whether the connection position of the Power Assembly & Wing Set is rm and the bolts are tightened in
place.
3. Special Warning
To avoid possible injury and loss, the following must be observed.
1. Use original accessories or accessories certied by Waydoo. The use of non-original accessories may cause
danger to the safe use of the hydrofoil.
2. Make sure no foreign matter (such as water, oil, sand, or soil) has entered any of the components.
Waydoo Flyer ONE Quick Start Guide Waydoo Flyer ONE Quick Start Guide
ENEN
9 10
All rights reserved by WaydooAll rights reserved by Waydoo

Troubleshooting
Possible Failures and Solutions
If there are any problems during use, stop operating the product, lay on the board, and paddle with your hands
until you return to land. After the problem is solved, you can use the board again. If there is any problem that
cannot be solved, contact the after-sales service in time.
1. The battery fault light turns red: Check if the temperature of the battery is too high. If the temperature is too
high, stop using it and wait for the battery to cool down before continuing to use. Check whether the battery level
is too low. If the battery is too low, charge immediately. If the problem is still not solved, contact after-sales service
in time.
2. The battery has no output: Check whether the power assembly and the battery are properly connected. If there
is any looseness, tighten the L-shaped bolts in time. Normally, the battery has output. The output indicator on the
display will continue to light up in blue.
3. The battery cannot be charged normally: First, check whether the fault indicator of the battery is on. If it is,
contact the after-sales service to repair or replace the battery, Next, check whether the charger indicator is
ashing red. If the charger is in good condition, check whether the AC plug of the charger and the integrated
battery port are properly connected. Tighten if they are loose. If the connection is normal, turn the charger over.
Make sure the rocker switch of the electrical appliance is in the ON position and then the battery should be able
to charge normally.
4. The motor keeps making abnormal noises during use: Immediately release the trigger of the remote control to
stop the motor, turn o the remote control, lay on the board, and paddle back to land using your hands. Take out
the battery and check whether there is any foreign matter in the propeller. If there is foreign matter, remove the
propeller protective cover and the propeller for cleaning. Before inspecting the propeller, make sure that the
battery is disconnected and remove the battery.
1. After use, press and hold the Power Button of the Jet ONE Controller for 5 seconds, and power o the Jet ONE
Controller.
2. Take the board out of the water. Short press the Power Button of the PowerFlight Cell and then long press for 2
seconds. The PowerFlight Cell will beep to conrm it is powered o. Unscrew the Rotary Locks and remove the
PowerFlight Cell.
3. Unscrew the Main Wing and Tail Wing Fixing Bolts and remove the wings.
4. Unscrew the L-shaped Fixing Bolts to uninstall the Power Assembly.
5. Rinse o the sand and dirt from the Board and other parts with fresh water.
5. After Use
Waydoo Flyer ONE Quick Start Guide Waydoo Flyer ONE Quick Start Guide
1. Do not disassemble or modify the PowerFlight Cell for other purposes. Otherwise, the warranty will be invalid.
2. Do not disassemble, puncture, impact, or drop the PowerFlight Cell.
3. Do not operate the PowerFlight Cell with wet hands.
4. Do not install or remove the PowerFlight Cell in water.
5. Do not discard the PowerFlight Cell randomly.
6. Do not expose the PowerFlight Cell to direct sunlight, re, or place it in an environment where the temperature
exceeds 60° C (140° F).
7. Use the standard charger for charging.
8. Place the PowerFlight Cell in a safe place and avoid contact with young children or animals.
9. Check whether the PowerFlight Cell is normal before use. Using abnormal batteries may cause damage, electric
shock, re, and even life-threatening situations.
10. If you need to store the PowerFlight Cell for more than one month, maintain the battery level at 40-60%.
11. The transportation of the PowerFlight Cell needs to comply with relevant local laws and regulations.
It is prohibited to use this product in waters where there are swimmers or divers. It is forbidden to operate in
restricted trac areas. Make sure to strictly abide by local laws and regulations.
1.2m
Wide Open Water Operating
Range
Bluetooth SignalNo Obstacle in
the Water
Stay away from people, boats, oating objects, a large number of animals and plants, obstacles, and other waters
when operating.
Refrain from ying in weather such as rain, thunder, snow, heavy fog, strong wind, and storms.
Deep Water Area
4. Restrictions and Local Regulations
ENEN
11 12
All rights reserved by WaydooAll rights reserved by Waydoo

5. The motor stops rotating during use:
Immediately release the trigger of the remote control to stop the motor, turn o the remote control, and lay on
the board and paddle back to land using your hands. Check whether the status indicator of the remote control
shows normal connection status. Next, check whether the battery level is normal, and then check whether the
powertrain and the board are loose. If it is loose, tighten it in time. If the problem is not solved after attempting
the above steps, remove the battery and check whether sea water has seeped into the metal joints or if there is
any corrosion. If the above situation has occured, rinse the plug with fresh water and dry it with a rust remover to
remove the rust on the metal joints. Finally, wash and dry the plug.
6. The machine shakes, vibrates, and it is dicult to maintain balance during use: Immediately release the trigger
of the remote control to stop the motor, turn o the remote control, lay on the board, and paddle back to land
using your hands. Remove the battery and check whether the mounting bolts of the power assembly are loose. If
loose, tighten them in time.
7. The remote control connection appears intermittent during use: Immediately release the trigger of the remote
control to stop the motor, turn o the remote control, lay on the board, and paddle back to land using your hands.
Turn on the remote control and check whether the Bluetooth icon is ashing. If it is ashing, restart the battery
and pair again using Bluetooth. If the problem is still not resolved, contact after-sales service in time.
8. The remote controller has a fault:“Err.1” = Angle sensor initialization failed. “Err. 2”Spiash initialization failed.
“Err. 3” = Angle sensor and spiash initialization failed. “Err. 4” = GPS failed. “Err. 7”= Angle sensor initialization,
spiash initialization, and GPS failed.
6. After cleaning, wait for the moisture of all parts to dry before putting the parts back into the package.
7. When storing this product, avoid direct sunlight. Ultraviolet rays and high temperatures will cause permanent
damage to the product.
8. To ensure safety, make sure to turn o the remote control and battery when transporting this product.
Maintenance
Regularly check the waterproof components (such as the Jet ONE Controller, the PowerFlight Cell, and the mast
head) for damage and the status of each module of the power system and control system.
1. After using the product, turn o the Jet ONE Controller and PowerFlight Cell.
2. To clean the Power Assembly & Wing Set, align the water inlet of the motor mount with a fresh water pipe, and
clean the motor mount for approx. 30 seconds to ensure that the motor mount is clean and free of debris. Next,
clean the motor shroud, propeller, and propeller guard. Afterwards, clean the mast plug. Make sure to remove any
salt, sand, or other debris that is found. Finally, clean the mast.
3. Clean the board, battery mounting position, and the mast mounting base and other parts with fresh water to
ensure that there is no salt, sand, or other debris remaining. Wipe with a dry towel and let sit in a dry environment
to remove the remaining water.
4. Clean the battery, battery integrated ports, and buttons with fresh water. Use a dry towel and let stand in a dry
environment to remove the remaining water.
5. Clean the remote control. Pay special attention to the location of the remote control trigger. If you nd that
there is a jam when pulling the trigger, check whether there is any gravel in the trigger. If so, rinse the gravel out
with clean water.
After-sales Service Plan
Waydoo Flyer ONE – Warranty Period
1. When contacting Waydoo, explain in detail the problem with the product.
2. Waydoo's technical support sta will try to diagnose and solve your problem by phone, email, or remote
assistance.
3. If you still cannot solve your problem, send the product to Waydoo for further testing. Waydoo will arrange
services for you according to the corresponding warranty service type of the product.
Non-after-sales Coverage
1). Damage caused by transportation or loading and unloading during the return, exchange, and repair. 2). Any
unauthorized modication, disassembly, opening, and repair without ocial authorization. 3). Battery damage
caused by any accidental factors or human factors, such as obvious hard object damage, cracks, severe deforma-
tion, broken power cord, disconnection, etc. 4). Product failure or damage caused by installation, use, mainte-
nance, and storage not in accordance with the requirements of the instruction manual. 5). Damage due to circuit
modication, battery pack modication, or using unmatched chargers guided by unocial instructions. 6).
Damage caused by using outside the safe load range of the product. 7). Damage caused by forced use of the
product when the parts are damaged. 8). Damage caused by using batteries with quality problems. 9). The
product or component has the identication label changed or removed. 10). Failure or damage caused by force
majeure (such as re, earthquake, ood, etc.). 11). Products or parts that have exceeded the warranty period.
1 year
1 year
1 year
1 year (or less than 300 cycles)
1 year
1 year
EPP Board
Mast & Power Assembly
Main Wing and Tail Wing
PowerFlight Cell
Jet ONE Controller
Fast Charger
Waydoo Flyer ONE Quick Start Guide Waydoo Flyer ONE Quick Start Guide
ENEN
13 14
All rights reserved by WaydooAll rights reserved by Waydoo

FCC STATEMENT
1.This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause
undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a
residential installation.This equipment generates uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures: Reorient or relocate the receiving
antenna. Increase the separation between the
equipment and receiver. Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected. Consult the dealer
or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 5mm between the
radiator & your body.