KWIK GOAL Pro Premier 2B8 User manual

NZ225 Rev. 03/04/19
140 Pacific Drive Quakertown, PA 18951
(P) 215-536-2200 / (P) 800-531-4252 / (F) 215-536-4309 / (F) 800-778-8869
Visit our website @ kwikgoal.com
2005, Rev 2019 Kwik Goal Ltd.
ASSEMBLY INSTRUCTIONS FOR 2B8 PRO-PREMIER WORLD COMPETITION SOCCER GOAL
1. Unpack all parts and check for damage that may have occurred during shipping. If damage has occurred, notify
Kwik Goal immediately. Lay out all parts. Remove all cardboard and packaging immediately. Wet or damp
packaging may damage contents.
2. Read through entire instruction before beginning assembly and installation.
NOTE: Components may be packaged in one or more additional boxes.
Left Post (1)
(Part# UZ395)
129-3/8”
Right Post (1)
(Part# UZ396)
129-3/8”
Left Base (1)
(Part# UZ925)
72”
Crossbar (1)
(Part# UZ393)
280”
Bottom Crossbar (1)
(Part# UZ927)
277-7/8”
Right Base (1)
(Part# UZ926)
72”
®
Parts
***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Movable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
Any modifications to this or any Kwik Goal product will void any and all warranties.

NZ225 Rev. 03/04/19
140 Pacific Drive Quakertown, PA 18951
(P) 215-536-2200 / (P) 800-531-4252 / (F) 215-536-4309 / (F) 800-778-8869
Visit our website @ kwikgoal.com
2018 Kwik Goal Ltd.
IMPORTANT GOAL SAFETY INSTRUCTIONS
READ CAREFULLY
1. Check for structural integrity and proper connecting hardware before every
use. Replace damaged or missing parts or fasteners immediately.
2. Safety/Warning labels must be clearly visible.
3. Securely anchor movable soccer goals at ALL times.
4. Always instruct players, managers, coaches, trainers, teachers, maintenance
workers and all other personnel who might come in contact with the goal,
on the safe handling of and potential dangers associated with movable
soccer goals.
5. Always exercise extreme caution when moving goals and provide adequate
manpower to move goals of varied sizes and weights. Movable soccer goals
should only be moved by authorized personnel.
6. NEVER allow anyone to climb on the net or goal framework.
7. Movable soccer goals should only be used on LEVEL fields, NEVER on a slope
or hill area.
8. Remove nets when goals are not in use.
9. Most of the tip-over injuries occurred when goals were unattended. Anchor
or chain one goal to another or to nearby fence posts, dugouts, or any other
similar sturdy fixture when not in use. If this is not practical, store movable
soccer goals in a place where children cannot have access to them.
10. Fully disassemble goals for seasonal storage.
WARNING

NZ225 Rev. 03/04/19
Net Frame Channel
Connector (2)
(Part# UZ909)
T-Spacer (2)
(Part# WZ442)
Channel Spacer (6)
(Part# UZ812)
Net Frame
Connector Plate (2)
(Part# UZ928)
Net Fastener (1)
(Part# MNF-1
ROLL OF 12FT)
Net Clip (80)
(Part# 10B3101
PACK OF 100)
Net (1)
(Part# 3B1502)
Back Pole (3)
(Part# UZ1122)
153”
Back Pole Ground
Sleeve (3)
(Part# UZ463)
24”
3” dia.
Post Ground Sleeve (2)
(Part# UZ65)
24”
4-3/4” dia.
Post Ground Sleeve Cap (2)
(Part# UZ66)
4-3/8” dia.
Back Pole Ground
Sleeve Cap (3)
(Part# UZ56)
2-11/16” dia.
Parts continued:
***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Movable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
Any modifications to this or any Kwik Goal product will void any and all warranties.

Hardware
Hardware may be packaged separately Note:
in one or more boxes. Open all packages
before beginning assembly.
1/4” x 1/2” Set Screw (Part# TZ252) (2) Tension Strap (Part#10B5801) (3)
3/8“ x 1-1/4” Hex Bolt (Part# TZ59) (12) Snap Link (VZ189) (1)
3/8" x 7/8" Hex Bolt (Part# TZ249) (6) Tension Mechanism (VZ232) (1)
3/8“ Lock Washer (Part# TZ65) (16) Nylon Strap (* See Below) (1)
3/8“ Flat Washer (Part# TZ60) (16) 5/16” Lock Nut (TZ5) (1)
3/8" Square Nut (Part# TZ247) (4) 5/16” Flat Washer (TZ4) (2)
5/16” x 3-1/4” Hex Bolts (Part# TZ206) (2) 5/16” x 3-1/4” Hex Bolt (TZ206) (1)
5/16" Flat Washer (Part# TZ4) (4) 3/8” x 3-1/4” Eye Bolt (TZ198) (1)
5/16” Lock Nut (Part# TZ5) (2) 3/8” Lock Nut (TZ197) (1)
3/8” Flat Washer (TZ189) (1)
*Replacement nylon straps available in set of 3 straps (Part#VZ607)
Assembly Tools
Mallet
Scissors
Allen wrench
1/8”
Ratchet with
1/2”& 9/16”
Sockets
1/2”& 9/16”
Wrenches
9/16
NZ225 Rev. 03/04/19
***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Movable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
Any modifications to this or any Kwik Goal product will void any and all warranties.

3. Attach left post and right post to crossbar as shown. Note
direction of decals on crossbar before fastening. Be sure
connections are pressed firmly together before tightening hex
bolts.
T Spacer
1/4” X 1/2”
Set Screw
3/8" Square Nuts
3/8"
Square Nuts
T Spacer
Left Post
Crossbar
Right Post
Left Post
Post Ground Sleeve
Post Ground Sleeve
4. Insert two 3/8” square nuts and one T-spacer into left post and
right post. Lock T-spacer into position with 1/4” x 1/2” set screws.
Slide front post ground sleeves onto left post and right post.
Left Post
Crossbar
Right Post
Channel
Spacer
Crossbar 3/8” X 1-1/4” Hex Bolt
3/8” Lock Washer
3/8” Flat Washer
Right Post
NZ225 Rev. 03/04/19
***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Movable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
Any modifications to this or any Kwik Goal product will void any and all warranties.

Playing Field
Top View
9' 6"
288"
180" 180"
Face of goal NOT beyond this point
Center of Goal Line
Right Post
Left Post
Back Pole Back Pole
Back Pole
5. Mark field location for posts and back poles.
6. Dig holes a minimum of 41 1/4" deep and 24" across.
Fill bottom of holes with 1” diameter stone until the
hole is 29 1/4" in depth, until the top of ground
sleeve is 5” below field surface.
The stone base allows water and small debrisNOTE:
to flow through the hole located in the bottom of
ground sleeve.
5“ Below Surface
Min. 41-1/4"
Min. 24"
Concrete
Ground Sleeve
Post/Poles
1” dia. Stone
for
Drainage
30
Approx.
29-1/4"
NZ225 Rev. 03/04/19
***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Movable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
Any modifications to this or any Kwik Goal product will void any and all warranties.

Post Ground Sleeve
Down - Bow
Up - Arch Crossbar
Cause Bow
in Crossbar
Cause Bow
in Crossbar
Left Post Right Post
Concrete
Field Surface
Large Stone
Cause Arch
in Crossbar
Cause Arch
in Crossbar
Front View
7. Set assembled goal posts with post ground sleeves, back poles and back poles ground sleeves into holes.
Plumb and level goal, making sure the bottom of crossbar is 8 feet from the field surface. Face of the goal
post should not enter into playing field. Seal space between left post and right post, and post ground
sleeve with tape, or small bead of sealer. Do the same for the back pole and back pole ground sleeve. This will
stop debris from entering ground sleeves during construction.
8. Fill holes with concrete, flush to the top of ground sleeves. Be sure to level back poles before concrete begins
to cure. After concrete has fully cured, see Step 15 for test procedures to ensure the goal has been
anchored properly.
9. Attach net frame channel connector, to left post and right post, as shown.
3/8” x 7/8” Hex Bolts
3/8” Lock Washers
3/8” Flat Washers
3/8” Square Nuts
Field Surface
Net Frame
Channel Connector
NZ225 Rev. 03/04/19
***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Movable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
Any modifications to this or any Kwik Goal product will void any and all warranties.

10. Assemble left net frame, right net frame, and rear net frame.
Left Net Frame
Right Net Frame
Rear Net Frame
3/8” x 1-1/4” Hex Bolts
3/8” Lock Washers
Right Net Frame
3/8” Flat Washers
Channel Spacer
Insert into net channel.
Channel Spacer
Insert into net channel.
Net Frame Connector Plate
Insert under net channel.
3/8” x 1-1/4” Hex Bolts
3/8” Lock Washers
3/8” Flat Washers
Rear Net Frame
Field Surface
Post
5/16” Flat Washer
5/16” x 3-1/4” Hex Bolt
5/16” Flat Washer
Right Net Frame
5/16” Lock Nut
Net Frame
Channel Connector
11. Attach assembled net frame to posts of assembled goal, as shown.
NZ225 Rev. 03/04/19
***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Movable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
Any modifications to this or any Kwik Goal product will void any and all warranties.

Back Pole
Nylon Strap
3/8” Eye Bolt
3/8“ Flat Washer
& 3/8“ Lock Nut
5/16" Flat Washer
5/16” Lock Nut
Ratchet Binder
5/16"
Flat Washer
5/16" X 3-1/4"
Hex Bolt
12. Assemble back poles and net straps accordingly.
Nylon Strap
Loop at this side
Slide non loop
end through in the
direction as shown.
Ratchet Binder & Strap Assembly
Side View
Ratchet Lever
Tension
Release
Ratchet Binder
Nylon Strap
Ratchet Binder & Strap Assembly
Front View
Bolt Hole
Ratchet Lever
NZ225 Rev. 03/04/19
***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Movable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
Any modifications to this or any Kwik Goal product will void any and all warranties.

13. To attach net to goal, place base of net clip into channel and turn
90 degrees to lock into place.
CAUTION: DO NOT ATTEMPT TO CLIMB ON GOAL WHILE
ATTACHING NET.
Net Fastener
Post Net Frame
Lift
Lift
NOTE: Attach net to post of goal with net fastener. Be sure
to cut pieces to a length of 6-1/2”which will allow a 2“
over lap.
14. To lift net frame up off field surface see below. Clear away all soil and debris from top of post ground sleeves and
back pole ground sleeves before removing goal. Be sure to put post ground sleeve caps and back pole ground
sleeve caps in all ground sleeve openings. Be sure to disassemble and store goal in a safe place to prevent injury.
Repeat for back pole removal.
See GUIDELINES FOR MOVEABLE SOCCER GOALS, included for proper storage procedures.
Net Clip
Net
Crossbar
24 Net Clips
Left Post
8 Net Clips
Left Net Frame
7 Net Clips
Right Net Frame
7 Net Clips
Rear Net Frame
26 Net Clips
Right Post
8 Net Clips
Snap
Link Net
NZ225 Rev. 03/04/19
***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Movable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
Any modifications to this or any Kwik Goal product will void any and all warranties.