WB Manufacturing Quad XL User manual

1
wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Quad XL
Assembly Instructions
Before you begin, please make sure all parts and proper quantities are included. (See Part Identier Key) Any parts damaged during shipment must be
reported within 24 hours of receipt. To report information regarding damages or if you have any questions, please call 800.242.2303.
Step 1:
• Place the longer base cabinet upside down on a
protected at surface with it’s caster base facing up.
(Upon installer’s discretion, remove doors and shelving
before turning cabinets over to lessent the weight of
the cabinets.)
Step 2:
• Align caster with the threaded inserts. (See image to the
right; threaded inserts are marked in red as an example
for assembly instruction ONLY.)
• Use the ¼-20x25mm joint connector bolts to attach
casters to the base cabinet.
• Repeat for remaining casters. (Make sure you have two
locking and two non-locking casters on this cabinet.)
Step 3:
• Repeat Steps 1-2 for the two smaller base cabinets.
Step 4:
• With someone’s help, position the cabinets right side up.
Make sure to have the all locking casters’ levers pushed
down to secure cabinet in place.
Step 5:
• Align the pre-drilled holes in cabinet (B) with the
threaded inserts in cabinet (A).
• With cabinets aligned together, connect them with
the ¼-20x30mm joint connector bolt w/ loctite going
through cabinet (B). Use a 4mm Allen wrench or 4mm
Hex bit and a screw gun to tighten as needed.
• Use 4 bolts total to connect cabinet (A) to cabinet (B).
• Repeat Step 5 with the second base cabinet.
V042519 subject to change.
Step 5
Steps 1-2
A
B
Image shown is
upside down in
order to apply
casters.

2
wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Step 6:
• Place top on base cabinets. Align pre-drilled holes on the base
cabinets with treaded inserts in the top. (There will be two pre-
drilled holes in cabinet (A) and one pre-drilled hole in each of the
smaller cabinets.)
• Using a ¼-20x30mm joint connector bolt, (going through one of
the base cabinets) insert the bolt through the pre-drilled hole up
into the threaded insert of the top. Use a 4mm Allen wrench or
4mm Hex bit and a screw gun to fasten the bolt into place.
• Repeat Step 6 for the other base cabinets.
• If shelving and doors were removed, place shelving back rst and
then attach the doors.
Step 7:
• Wire pulls are factory installed on the inside of door/s to prevent
damage intransit. (If you have a base cabinet with double doors,
use the clear tab to open the doors.)
• Unscrew each wire pull handle using a Phillips drill bit and a
screw gun.
• Reattach with wire pull on the outside of the cabinet.
• Repeat for other wire pull.
Step 8Step 7
Quad XL
Assembly Instructions
Before you begin, please make sure all parts and proper quantities are included. (See Part Identier Key) Any parts damaged during shipment must be
reported within 24 hours of receipt. To report information regarding damages or if you have any questions, please call 800.242.2303.
A

3
wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Part # Description Qty.
0400236 ¼-20x30mm joint connector bolt w/ loctite
(Used to attach 2 smaller base cabinets to the larger base cabinet)
8
(4 per side)
040681 #10 1½” square-drive at head screw for wood
(Used to attach caster base to the 3 base cabinets)
12
(4 for each base cabinet)
Cast1
0400484 3” heavy duty plate casters w/ out brake 6
(2 for each base cabinet)
Cast1
0400485 3” heavy duty plate casters w/ brake 6
(2 for each base cabinet)
Cast1
04066947 ¼-20x25mm joint connector bolt (black)
(Used to apply casters)
48
(16 for each base cabinet)
0400236 ¼-20x30mm joint connector bolt (black)
(Used to attach base cabinet to top)
4
(2 for base cabinet w/ doors)
(1 for each base cabinet wo/ doors
Part Identifier Key
Tools Required
• 4mm Allen wrench OR
• 4mm Hex bit
• Drill extension
• Phillips drill bit
• Screw gun
• #2 square bit
Quad XL