Weego 44s User manual

Visit www.myweego.com/support for FAQs and additional
troubleshooting inquiries.
My unit won’t power on/charge/charge past a few lights
If your unit won’t power on, won’t take a charge OR won’t charge past a few lights
then it’s been overdischarged. This can happen if the engine pulled the Weego
battery past a certain limit during a jump start. It can also happen if the Weego is
not stored with a full charge, or is not recharged every 3-6 months during storage.
Please reach out to suppor[email protected] to let them know about this issue –
we’ll receive and test the overdischarged Weego, then determine if we can repair
it or if it needs to be fully replaced.
The Weego won’t jump start my vehicle
A few things can attribute to a failed jump start, which we listed below.
• Poor connection between the Weego clamps and vehicle battery:
the better the connection, the more likely you are to have a successful jump
• Dirty battery terminals: build up prevents all the available power from
reaching your battery
• Vehicle-specific compatibility issues: occasionally we come across a vehicle
that has unique power demands that a smaller model cannot fulfill, even
though it’s within our recommended engine range. In addition, vehicles with
heavier electronics can sometimes create issues when jumping with a Weego;
we mostly see this in push-to-start vehicles.
• Cold temperatures: Freezing temperatures create a lot of resistance in an
engine which means it can require up to 3.5X the usual amount of power to
get started; for example, an engine that usually needs 200A could need up to
700A in the extreme cold. In addition, if your Weego was stored in the cold
temps it will make it harder for the Weego to deliver its full power.
• Low-Charged Weego: it’s always best to work with full power on your
Weego if you can. Our jump starters perform better at 100% charge
than they do at 20% charge, especially when jumping larger engines.
TROUBLESHOOTING
© 2021. Weego is a division of Paris Corporation. US Patent #9692155, #D823243. All Rights Reserved. Rev 1/08
myweego.com
WEEGO CUSTOMER SUPPORT
We are dedicated to providing the best possible service. To reach Customer
Support, visit myweego.com/support or email [email protected].
Model No. 44s
QUICK START GUIDE
JUMP STARTER
READY Solid green light, no Sound
Smarty Clamps®detect that you have a good connection
and you are ready to jump.
Flashing Green & Red Lights + Beeping
REVERSE +/-
You attached the Smarty Clamps®on the wrong terminals.
Make sure the BLACK clamp is attached to the battery’s
NEGATIVE (-) terminal, and the RED clamp is attached to the
battery’s POSITIVE (+) terminal. If not attached properly,
Weego 44s will not let you jump your engine.
COOL DOWN
WAIT FOR
Flashing Red Light + Beeping
The Weego battery overheats after long cranks or excessive
current draw. Detach the Smarty Clamps®from the battery
and give the unit up to 3 minutes to cool down. Then, repeat
steps 2-5 under Jump Starting Your Engine.
Either you have a poor connection, or your battery is so dead
(nearly 0 volts) that your Weego clamps cannot register a
connection.
No Light
This means the vehicle’s battery is too weak to even start, OR
the system voltage of your vehicle is not compatible with your
Weego 44s (for 12V vehicles ONLY).
Solid Red Light, No Sound
There may be an engine size issue. If your engine is larger
than what we recommend, it will try to pull more power than
your Weego 44s is able to give. Please see Engine
Compatibility in the owner’s manual to determine if your
engine size falls within the scope of Weego 44s.
SEE REVERSE
Solid Red Light + Beeping
SEE REVERSE
UNDERSTANDING YOUR Smarty Clamps®
Your Smarty Clamps®have a “smart” box that will help guide you
through a jump with both sight and sound. It will let you know when it
is safe to jump or if there is an error.

Read all instructions and safety information prior to using this product.
Improper use of this product will void your warranty and may result in
product damage, excess heat, toxic fumes, re, and other unsafe
conditions for which Weego is not responsible.
Read vehicle owner’s manual rst: it may have specic cautions
and instructions about jumping your engine.
This product is for use on 12V Lead-Acid batteries only! DO NOT use
this product on any other voltage battery, such as 6V, 24V, etc. DO NOT
use this product on lithium-ion batteries.
Never jump or operate any engine in an enclosed area.
Put your vehicle in PARK and engage the emergency brake (boats and
powersports vehicles should be put in NEUTRAL).
TURN OFF ALL ELECTRONICS! – air conditioner, radio, lights, etc.
Remove any devices attached to your Weego 44s.
Never leave your Weego 44s connected to your engine’s battery unless
actively jumping.
Always disconnect the Smarty Clamps®from your Weego 44s when
not in use.
BEFORE YOU JUMP
JUMP STARTING
WARNING!
Exposed Metal Jaws May Be HOT After Use!
If you are having issues getting your engine started, see Troubleshooting for
further details and assistance.
JUMP STARTING YOUR ENGINE
1. Ensure your engine is completely OFF.
2. Securely connect the Smarty Clamps®to your Weego 44s.
3. Place your Weego 44s in a secure location.
4. Attach BLACK clamp to your battery’s negative (-) terminal, then the
RED clamp to your battery’s positive (+) terminal. Adjust your
Smarty Clamps®to achieve MAXIMUM contact with the terminals.
Poor connections will prevent you from starting your engine! Clear off
any dirt or buildup with a wire brush or a dry towel before connecting
your clamps.
5. Check your Smarty Clamps®lights. When you have a GREEN READY light,
start your engine. If the engine doesn’t start, check your Smarty Clamps®
lights and wait a minute before trying again.
6. After a successful start, disconnect the Smarty Clamps®from your
Weego 44s.
7. Detach the Smarty Clamps®from the battery.
8. You’re now good to go – be sure to run your engine for at least 15 minutes
before shutting it off again so it has time to recharge your battery.
Connect Clamps
Attach Black (-), Then Red (+)
Once it Starts, Disconnect Clamps
from Weego 44s
Detach Clamps From Battery
When You Have GREEN LIGHT On Your
Smart Box, Start Your Engine
Smarty Clamps®
Smarty Clamps®Socket
Battery Indicator Lights
5V/2A Recharge (Input) Port
CHARGE UP YOUR WEEGO 44s
When you unpack your new Weego 44s for the first
time, charge it up to 100% using the Micro USB
Charging Cord provided. Make sure you use a USB
enabled wall adapter (like the one that comes
with your smartphone or tablet) with an output of
2.1A to charge as quickly as possible. (Output
ratings are always located on the USB adapter).
Weego 44s will last up to a year without
recharging, but to keep it topped off, recharge it
every 6 months or so. Weego 44s will allow you to
charge & discharge your unit up to 1000 times,
which will give you a good 3-5 years of active use.
It takes 2.5 hrs. to fully charge using a
2.1A USB adapter. The indicator lights
will flash one by one while the unit is
charging. A solid light indicates a
completed level of charge.
Indicator
Lights
Sequence:
Indicator
Lights
Sequence:
20% Charged
40% Charged
60% Charged
80% Charged
100% Charged
GETTING TO KNOW WEEGO 44S