WEEGO CUSTOMER SUPPORT We are dedicated to providing the
best possible service. To reach Weego Customer Support, visit
Read all instructions and safety information prior to using this product.
Improper use of this product will void your warranty and may result in
product damage, excess heat, toxic fumes, re, and other unsafe
conditions for which Weego is not responsible.
Read vehicle owner’s manual rst: it may have specic cautions
and instructions about jumping your engine.
This product is for use on 12V Lead-Acid batteries only! DO NOT use
this product on any other voltage battery, such as 6V, 24V, etc. DO NOT
use this product on lithium-ion batteries.
Never jump or operate any engine in an enclosed area.
Put your vehicle in PARK and engage the emergency brake (boats and
powersports vehicles should be put in NEUTRAL).
TURN OFF ALL ELECTRONICS! – air conditioner, radio, lights, etc.
Remove any devices attached to your Weego 22s.
Never leave your Weego 22s connected to your engine’s battery unless
actively jumping.
Always disconnect the Smarty Clamps®from your Weego 22s when
not in use.
BEFORE YOU JUMP
JUMP STARTING UNDERSTANDING YOUR Smarty Clamps®
Your Smarty Clamps®have a “smart” box that will help guide you through a
jump with both sight and sound. It will let you know when it is safe to jump
or if there is an error.
READY Solid green light, no Sound
Smarty Clamps®detect that you have a good connection
and you are ready to jump.
Flashing Green & Red Lights + Beeping
REVERSE +/-
You attached the Smarty Clamps®on the wrong terminals.
Make sure the BLACK clamp is attached to the battery’s
NEGATIVE (-) terminal, and the RED clamp is attached to the
battery’s POSITIVE (+) terminal. If not attached properly,
Weego 22s will not let you jump your engine.
COOL DOWN
WAIT FOR
Flashing Red Light + Beeping
This happens when your Weego is cranked longer than the
recommended 3 seconds, or if your engine is trying to pull more
power than the Weego 22s is willing to provide. Detach the
Smarty Clamps®from the battery and give the unit up to 3
minutes to cool down. Then, repeat steps 2-5 under Jump
Starting Your Engine.
This means the vehicle’s battery is too weak to even start, OR
the system voltage of your vehicle is not compatible with your
Weego 22s (for 12V vehicles ONLY).
Solid Red Light, No Sound
There may be an engine size issue. If the engine you’re
connecting to is larger than what we recommend, it will try to pull
more power than your Weego 22s is able to give. If, this happens
Weego 22s will prevent you from jumping your engine. Please see
Engine Compatibility in your owner’s manual to determine if your
engine size falls within the scope of Weego 22s.
SEE REVERSE
Solid Red Light + Beeping
SEE REVERSE
the system voltage of your vehicle is not compatible with your
There may be an engine size issue. If the engine you’re
If you are having issues getting your engine started,
see Troubleshooting section in your owner’s manual
for further details and assistance.
JUMP STARTING YOUR ENGINE
1. Ensure your engine is completely OFF.
2. Securely connect the Smarty Clamps®to your
Weego 22s.
3. Place your Weego 22s in a secure location.
4. Attach BLACK clamp to your battery’s negative (-)
terminal, then the RED clamp to your battery’s
positive (+) terminal. Adjust your Smarty Clamps®
to achieve MAXIMUM contact with the terminals.
Poor connections will prevent you from starting your
engine! Clear off any dirt or buildup with a wire brush
or a dry towel before connecting your clamps.
5. Check your Smarty Clamps®lights. When you
have a GREEN READY light, start your engine. If the
engine doesn’t start, check your Smarty Clamps®
lights and wait a minute before trying again.
6. After a successful start, disconnect the Smarty
Clamps®from your Weego 22s.
7. Detach the Smarty Clamps®from the battery.
8. You’re now good to go - be sure to run your engine
for at least 15 minutes before shutting it off again so
it has time to recharge your battery.
Connect ClampsConnect Clamps
When You Have
GREEN Light,
Start Your Engine
When You Have
GREEN Light,
Start Your Engine
Once it Starts,
Disconnect Clamps
from Weego 22s
Once it Starts,
Disconnect Clamps
from Weego 22s
Detach Clamps
From Battery
Detach Clamps
From Battery
Attach
BLACK (-),
Then RED (+)
Attach
BLACK (-),
Then RED (+)
