Weego 44 User manual

Voltage incompatibility: your vehicle’s battery is too weak
There may be an engine incompatibility issue. If the engine you’re
connecting to is larger than what we recommend, it will try to pull
more power than your Weego 44 is able to give. Please see
QUICK START GUIDE

Voltage incompatibility: your vehicle’s battery is too weak
There may be an engine incompatibility issue. If the engine you’re
connecting to is larger than what we recommend, it will try to pull
more power than your Weego 44 is able to give. Please see
CHARGE UP YOUR WEEGO 44
When you unpack your new Weego Jump Starter 44 for
the first time, charge it up to 100% with either the wall
or car charger provided. Remember to recharge your
Weego 44 every 6 months, even when you’re not using
it – it will help extend its lifespan.
POWERING ON/OFF
There’s a Power ON/OFF Button on the back of your
Weego 44. While powered “ON”, the blue power button
will remain illuminated. Make sure you turn OFF your
Weego 44 after every use; leaving it on slowly drains
the battery.
Indicator
Lights
Sequence:
20% Charged
40% Charged
60% Charged
80% Charged
100% Charged
Smarty ClampsTM
Power ON/OFF Button
15V/1A Recharge (Input) Port
Back of Unit
Lanyard Post
GETTING TO KNOW WEEGO 44
It takes 3 hrs. to fully charge. The
indicator lights will flash one by one
while the unit is charging. A solid light
indicates a completed level of charge.
500 Lumen LED Lights
Smarty ClampsTM Socket
19V/3.5A Laptop Port
(Blue)
12V/10A Accessory Port
(Black)
Detect-O-Matic™USB Port
5V, 9V or 12V/2.4A
Battery Indicator Lights
Flashlight Button

Read all instructions and safety information prior to using this product.
Improper use of this product will void your warranty and may result in
product damage, excess heat, toxic fumes, fire, and other unsafe
conditions for which Weego is not responsible.
Read vehicle owner’s manual first: it may have specific cautions
and instructions about jumping your engine.
This product is for use on 12V Lead-Acid batteries only! DO NOT use
this product on any other voltage battery, such as 6V, 24V, etc. DO NOT
use this product on lithium-ion batteries.
Never jump an engine in an enclosed area.
Put your vehicle in PARK and engage the emergency brake (boats and
powersports vehicles should be put in NEUTRAL).
TURN OFF ALL ELECTRONICS! – air conditioner, radio, lights, etc.
Remove any devices attached to your Weego 44.
Never leave your Weego 44 connected to your engine’s battery unless
actively jumping.
Always disconnect the Smarty Clamps™ from your Weego 44 when
not in use.
BEFORE YOU JUMP
JUMP STARTING
WEEGO CUSTOMER SUPPORT We are dedicated to providing the
best possible service. To reach Weego Customer Support, visit
myweego.com/support or email suppor[email protected]. For the full
Owner’s Manual, please visit www.myweego.com/support/.

Connect Clamps
Attach Black (-), Then Red (+)
Power ON
Once it Starts, Disconnect Clamps
from Weego 44 Detach Clamps From Battery
When You Have GREEN LIGHT On Your
Smart Box, Start Your Engine

JUMP STARTING YOUR ENGINE
1. Ensure your engine is completely OFF.
2. Securely connect the Smarty Clamps™ to your Weego 44, then power ON.
3. Attach BLACK clamp to your battery’s negative (-) terminal, then the RED clamp
to your battery’s positive (+) terminal. Adjust your Smarty Clamps™ to
achieve MAXIMUM contact with the terminals. Poor connections will prevent you
from starting your engine! Clear off any dirt or buildup with a wire brush or a dry
towel before connecting your clamps.
4. Place your Weego 44 in a secure location or suspend using the provided hook &
lanyard so it won’t fall. Check your Smarty Clamps™ lights.
5. When you have a GREEN READY light, start your engine. If the engine doesn’t
start, turn off your vehicle and check your Smarty Clamps™ lights.
6. After a successful start, quickly disconnect the Smarty Clamps™ from your
Weego 44.
7. Detach the Smarty Clamps™ from the battery.
8. You’re now good to go - be sure to run your engine for at least 15 minutes before
shutting it off again so it has time to recharge your battery.
If you are having issues getting your engine started, see the Troubleshooting
section in your online owner’s manual for further details and assistance.
WARNING!
Exposed Metal Jaws May Be HOT After Use!

UNDERSTANDING YOUR Smarty Clamps™
Your Smarty Clamps™ have a “smart” box that will help guide you through a
jump with both sight and sound. It will let you know when it is safe to jump
or if there is an error.
READY Solid green light, no sound
Smarty Clamps™ detect that you have a good connection
and you are ready to jump.
No light, no sound
You either have a very poor connection and the clamps cannot
detect they are connected to a battery, OR your vehicle battery is
so weak that it cannot be jumped, OR your Weego is not charged
to 20% or more (2 LED lights) and clamps cannot function..
Flashing green & red lights + beeping
REVERSE +/-
You attached the Smarty Clamps™on the wrong terminals.
Make sure the BLACK clamp is attached to the battery’s
NEGATIVE (-) terminal, and the RED clamp is attached to the
battery’s POSITIVE (+) terminal. If not attached properly, Weego
44 will not let you jump your engine.
COOL DOWN
WAIT FOR
Flashing red light + beeping
The battery was cranked longer than the recommended 3
seconds, or the temperature protection was triggered. Detach
the Smarty Clamps™ and give the unit 3 minutes to cool
down. Then, repeat steps 2-5 under Jump Starting Your Engine.
Voltage incompatibility: your vehicle’s battery is too weak
(< 2V) or too high (>13V)* to safely jump start.
Solid red light, no sound
There may be an engine incompatibility issue. If the engine you’re
connecting to is larger than what we recommend, it will try to pull
more power than your Weego 44 is able to give. Please see Engine
Compatibility to determine if your engine size falls within the scope
of Weego 44.
SEE BACK
Solid red light + beeping
SEE BACK
Voltage incompatibility: your vehicle’s battery is too weak
There may be an engine incompatibility issue. If the engine you’re
connecting to is larger than what we recommend, it will try to pull
more power than your Weego 44 is able to give. Please see

Visit www.myweego.com/support/ for FAQs and additional
troubleshooting inquiries.
I can’t get the Smarty Clamps™ green light to appear
•Do you have a good connection?
A poor connection between the clamps and the terminals can be the
difference between a successful and failed jump. Adjust the clamps to
make sure they’re making maximum contact with your terminals, then
try again.
•Are your battery terminals dirty?
Build-up on your battery terminals can prevent you from getting a stronger
connection and can be the difference between a successful and failed
jump. See your vehicle owner’s manual for the best way to safely remove
buildup from your terminals.
•Are your battery terminals dirty?
Build-up on your battery terminals can prevent you from getting a stronger
connection and can be the difference between a successful and failed
jump. See your vehicle owner’s manual for the best way to safely remove
buildup from your terminals.
I followed the necessary steps but my engine is still unable to start. Now what?
•Does your Weego 44 have enough charge?
You can use your Weego 44 at any level of charge but peak performance is
best achieved with a fuller charge (greater than 80%, or 4 lights) - if operating
at less than 80%, we suggest recharging your Weego 44, if possible.
•Your engine may be too large/powerful for your Weego 44
Our batteries work hard to supply the power you need, but some engines
demand more than your Weego 44 can give. You may want to try the
next-larger Weego to better suit your needs. See Engine Compatibility in
the online Owner’s Manual (pages 12-13) to determine which Weego is
best for you.
•Your vehicle battery voltage may be too low or too high.
Weegos are designed to jump start batteries between 2V and 13V. If your
vehicle battery measures lower or higher than this range, the clamps will
not work for safety reasons.
TROUBLESHOOTING

Voltage incompatibility: your vehicle’s battery is too weak
There may be an engine incompatibility issue. If the engine you’re
connecting to is larger than what we recommend, it will try to pull
more power than your Weego 44 is able to give. Please see
Charge your phone, tablet and other
portable devices with your Weego 44 using
your own USB charging cord.Your Weego 44
comes equipped with Detect-o-Matic™
USB Charging. This intelligent charger
communicates with your device to detect
and deliver the fastest-possible charge.
To charge your devices, plug your charging
cord into your Weego 44 USB port, and
connect to your device. Power on your Weego 44 and start charging!
USB CHARGING
USB Charging Port
LIGHTING
Your Weego 44 comes with a 500 lumen LED
flashlight. Power on your Weego 44, then
briefly press and release the flashlight button
to initiate the following sequences:
• 1st click: Normal • 2nd click: Strobe
• 3rd click: SOS • 4th click: OFF
You can also skip directly to the OFF position
by holding down the flashlight button.
Your Weego 44 will give you up to 14 hours of flashlight time and up to 28 hours
of strobe & SOS light on a full charge.
© 2016. Weego is a brand of Paris Corporation. Patents Pending. All Rights Reserved. Rev 08/17
Flashlight Button