WESLOCK 2100 Series Instruction Manual

INSTRUCTIONS FOR INSTALLING YOUR WESLOCK PRODUCT
PARTS INCLUDED
REQUIRED TOOLS
SCAN THE CODE FOR
INSTALATION VIDEOS
GLOSSARY OF TERMS
Wood Screws (x8)
Traditionale Collection
Please reference www.weslock.com for the most current instructions.
Entry Handle Set
2100 Series
Do not insert key, or unlock handle before installation. Doing so may result in removal of the cylinder assembly.
Technical language used in this document
For mounting strikes & faceplates.
Measuring Tape
Or other measuring tool
Screwdriver
Phillips and flat blade
Wood Chisel
*Only if prepping a new door
Writing Utensil
*Only if prepping a new door
DOOR PREP INSTRUCTIONS 2 WESLOCK.COM
Interior Knob/Lever
Assembly
Interior knob / lever, rosette
& spindle
XL 3” Wood Screws (x2)
For mounting strike (optional).
MORTISE
Entry Keys (x2)
For unlocking
the deadbolt.
Deadbolt Latch
Engages strike with door closed.
Strikes (x6)
Install on door frame.
Interior Deadbolt
Assembly
Exterior Deadbolt
Assembly
Exterior Grip Assembly
Exterior handle & thumb piece.
Assembly Screws (x4)
For mounting interior deadbolt
assembly.
Foot Screw Cap Assembly
Faceplates (x4)
For covering a mortise latch.
* Only use one (1-3/4” 0R 2-1/4”)
screw based on thickness of door.
Iron Door Latch Casing
* Slide over thumbpress latch for
iron door application.
MORTISE
Thumb Press Latch
MORTISE
Engages strike with door closed.
Assembly Screws (x2)
Pre-installed on Exterior Grip Assembly
for mounting interior knob / lever
assembly. 1-1/4”
CROSS BORE
EDGE BORE
THUMB PRESS LATCH
DEADBOLT LATCH
* For Non-Mortise applications
see below parts.
* Only use two (2-1/4” OR 2-3/4”)
screws based on thickness of door.
* For Non-Mortise applications
see below parts.
* For Non-Mortise applications
see below parts.
FACEPLATES (X4) DEADBOLT LATCH THUMB PRESS LATCH
* Non-Mortise (Drive-In) Application

NON-MORTISENON-MORTISE
IDENTIFY THE LATCH TYPE FOR YOUR DEADBOLT AND THUMBPRESS LATCH
This will determine how you install the latch assembly in section 7.
DETERMINE THE BACKSET OF YOUR DEADBOLT LATCH AND THUMBPRESS LATCH
The length of your latch assembly will be determined by your backset measurement.
To change right or left hand setting (factory setting is right hand) of the exterior side of the entry
handle. The nylon block must be installed and is required for proper functionality of spindle.
MORTISE
ADJUSTING THE HANDING OF YOUR ENTRY HANDLE
MEASURE THE DOOR IF MEASUREMENT = 23/8”
Latch leaves the factory with this setting.
No adjustment is necessary.
KEEP
ADJUSTMENT
PIN IN PLACE
GRASP ADJUSTMENT
PIN ON BOTH SIDES
LIFT UP AND SLIDE
BACK TO 2-3/4” SLOT
1
1
2
Slide adjustment pin back to 23/4”slot.
Measure distance between center of
crossbore and edge of door.
IF MEASUREMENT = 23/4”
*Adapted
BACKSET LENGTH CENTER
LINE
Measure distance between center of
crossbore and edge of door.
BACKSET LENGTH CENTER
LINE REMOVE EXTENSION KEEP EXTENSION IN PLACE
No adjustment is necessary. Leave
extension attached to latch assembly.
Pry extension to remove it from the latch
assembly, using a at blade screwdriver.
B. Replace Spindle & Nylon BlockA. Remove Nylon Block & Spindle
CShaped Steel Spindle
Black Nylon Block
Using a screwdriver, slide the nylon block
out of it’s channel and remove from assembly.
With thumb and forenger grab spindle, pull
up and rotate 180°.
238
/234
/
238
/234
/238
/234
/
238
/234
/
STEP 1 STEP 2
Reinsert nylon block on opposing side of
assembly, adjacent to repositioned spindle.
STEP 3
MORTISE
NO MORTISE
NO MORTISE
LATCH
ASSEMBLY
LATCH
ASSEMBLY
LATCH
ASSEMBLY
FACEPLATE
MORTISE
LATCH
ASSEMBLY
FACEPLATE
MORTISE
NO MORTISE
NO MORTISE
LATCH
ASSEMBLY
LATCH
ASSEMBLY
LATCH
ASSEMBLY
FACEPLATE
MORTISE
LATCH
ASSEMBLY
FACEPLATE
MORTISE
NO MORTISE
NO MORTISE MORTISE
SNAP-ON
FACEPLATE
LATCH
ASSEMBLY
LATCH
ASSEMBLY
LATCH
ASSEMBLY
LATCH
ASSEMBLY
FACEPLATE
MORTISE
LATCH
ASSEMBLY
FACEPLATE
MORTISE
SNAP-ON
FACEPLATE
LATCH
ASSEMBLY

Deadbolt latch must be extended prior to installation.
INSTALLATION
PUSH FIRMLY ON
KNOB/LEVER TO
INSTALL
2
EXTEND LOCK
SCREWS PRIOR
TO INSTALL
(if necessary)
1
7B. Insert Non-Mortise Latches 7C. Install Exterior Deadbolt and
Grip Assemblies
A.
Insert deadbolt
tailpiece into cam
in deadbolt latch.
B.
Align notches on
grip housing with
proper grooves
(2-3/8 or 2-3/4) on
latch. Slide on.
At same time,
align and insert
foot screw
through
pre-drilled hole.
7D. Install Interior Deadbolt and
Knob/Lever Assemblies
7E. Install Strikes
7A. Insert Mortise Latches
WESLOCK WARRANTY INFORMATION
WESLOCK warrants to the purchaser that the products shall be free from defects in material workmanship for the LIFETIME of the product.
Provided the product was purchased from an authorized WESLOCK dealer, Weslock's sole obligation under this warranty shall be to repair or
replace product which WESLOCK determines to be defective. After such product is returned to WESLOCK by the purchaser with proof of
purchase and with shipping charges prepaid, will this warranty be honored. Homeowner - if the product was installed as original equipment
on a new home, you must provide the name of the builder, the date the home was built and your move-in date. If a mechanical defect has
occurred, it is your right by this warranty to contact Customer Service in Tulsa, Oklahoma at [phone] to arrange the return of the lock.
This warranty DOES NOT cover products which malfunction due to improper installation or misuse. Please register your product at
Weslock.com.
THANKS FOR CHOOSING US. WE HOPE YOU ENJOY YOUR NEW WESLOCK DOOR HANDLE.
Traditionale Collection
WARRANTY TERMS MECHANICALFINISH
Limited Lifetime Limited Lifetime
YOUTUBE
FACEBOOK
TWITTER
WEBSITE PHONE NUMBER
youtube.com/Weslock
DoorHardware
facebook.com/Weslock
DoorHardware
twitter.com/Weslock1
www.weslock.com
1-800-575-2658
EMAIL
[email protected]
or
[email protected]
FAX NUMBER
1-918-294-3869
Online Direct
BOLT
ADDITIONAL CUSTOMER RESOURCES
MORTISE NON-MORTISE
MORTISE
NO MORTISE
NO MORTISE
LATCH
ASSEMBLY
LATCH
ASSEMBLY
LATCH
ASSEMBLY
FACEPLATE
MORTISE
LATCH
ASSEMBLY
FACEPLATE
MORTISE
NO MORTISE
NO MORTISE
LATCH
ASSEMBLY
LATCH
ASSEMBLY
LATCH
ASSEMBLY
FACEPLATE
MORTISE
LATCH
ASSEMBLY
FACEPLATE