Wessex ATC120 User manual

1
OWNER’S MANUAL
Broadwood International
Bordon Trading Estate
Oakhanger Road
Bordon
Hampshire GU35 9HH
ATC120 and ATX120
Sweeper
Collector
T 01420 478111
F 01420 483000
E [e-mail]
W www.broadwoodintl.co.uk

2
PLEASE READ THE FOLLOWING PAGES
CAREFULLY BEFORE USING YOUR MACHINE
AND KEEP THIS MANUAL IN A SAFE PLACE

3
IMPORTANT SAFETY WARNING
Wessex sweepers are guarded for your protection but you must always observe certain
elementary precautions. Sweepers are potentially dangerous machines and should be used
with the greatest respect. Ensure that ALL operators are aware of the following
1. Never attempt any adjustment whatever, unless the machine and ALL its moving parts
are COMPLETELY at a standstill.
2. NEVER attempt to clear any obstructions around the machine unless ALL its moving parts
are COMPLETELY at a standstill, and the engine is switched off.
3. Never remove belt guards before all moving parts have come to a complete standstill and
the engine is switched off.
4. Never operate the machine with the safety guards removed. They are there for your
protection.
5. NEVER operate the machine with people behind; keep everybody (especially children) at a
safe distance (minimum 20 metres)
6. Stand well back from the machine when brushes are spinning
7. Read the instruction manual supplied with this booklet relating to the engine fitted to
your machine.
HEALTH AND SAFETY - Noise at work Regulations -
In compliance with the above regulations, this machine has been tested in operation with
the following result;
READING AT THE OPERATORS EAR
ATC / ATX Series Engine driven sweepers: 97.5 D.B.A
Depending on conditions and material being cut, this may alter; it is therefore advisable for
users to do their own assessment.

4
WARRANTY
Your Wessex PTO driven Sweeper-Collector is warranted free from defect in workmanship or
manufacture for one year from date of purchase. Any parts which appear to us to be
defective either in material or workmanship shall be replaced or repaired at no cost to the
purchaser, subject to the following conditions:
1. The registration card enclosed with this booklet must be returned to us within seven days
of purchase.
2. Any failure in the machine should be reported in the first instance to your dealer
who will act on your behalf to resolve the matter to your satisfaction.
3. The defective parts will be returned by your dealer to us accompanied by a full
statement describing the failure, and the circumstances and conditions in which the
failure occurred, within 5 working days of failure.
4. The following are specifically excluded from the terms of warranty:
(a) Fair wear and tear, especially to belts and brushes.
(b) Damage to brushes caused through incorrect positioning of the rotor (See
instructions).
(c) Damage caused by neglect or lack of lubrication.
(d) Damage caused by misuse or abuse.
(e) Damage caused while the machine is in transit.
(f) Damage caused to the frame of the machine by running the machine with an
unbalanced rotor.
5. The warranty is for the benefit of the first user only.
6. Wessex Machinery decisions will be final and binding.

5
SETTING UP YOUR WESSEX SWEEPER COLLECTOR
Your Wessex Sweeper-Collector has been designed to work in a wide variety of conditions
and IS a very simple machine to use There are one or two adjustments which ensure
optimum performance in all conditions.
The sweeper-Collector should be coupled to your vehicle using the ball hitch.
ADJUSTING THE ROTOR HEIGHT
The brush height can be adjusted by turning the adjuster.
The bristles should be in gentle contact with the ground for maximum pick up action (see
diagram).
If there is a drumming sound as the brush rotates, the brushes are set too low and should be
raised immediately to avoid damage to the brushes.
The brushes alone are not designed for scarifying or thatch removal, and damage caused
to the brushes will quickly occur if it is used for this purpose.
When using the sweeper it is a good idea to start off with the rotor fully raised, and lower it
if necessary until a satisfactory result is achieved.
Conditions will vary on the same site from day to day, dependant on weather conditions
There are sufficient adjustments of the brush strip and of the rotor position to ensure that
your sweeper does a good job in all conditions By experimenting with different adjustments
you will quickly find the optimum setting to suit your conditions.
COMPENSATING FOR BRUSH WEAR
The bristles on your sweeper rotor will wear in due course, and it will be necessary to adjust
the height accordingly.
The sweeper has been designed to work effectively until the bristles are approximately half
their original length. When the bristles wear beyond this point there is insufficient
momentum to throw the leaves and debris into the hopper, and it will be necessary to
replace the brushes on your machine.

6
EMPTYING THE HOPPER
The hopper of the Wessex Sweeper tips forward towards the vehicle using the hand winch
REMEMBER, RETAIN HOLD OF HANDLE WHEN CLOSING HOPPER.
SCARIFYING OPTION
This has been designed for the sweeping of horse manure or any similar material which
tends to stick in the grass
Tines should be set a few millimetres below the brush tip to loosen any compacted material
prior to sweeping.
MAINTENANCE
Check ALL FASTENING SETS after first 8 hours of work.
Rotor bearings & cross
Shaft End Bearings - Grease every 150 hours of work
Engine - Refer to Engine Manual
Hopper Bearing - Grease twice per year
Before putting the Sweeper away at the end of the season, we recommend that the inside of
the rotor shroud is thoroughly cleaned. Preferably with a power washer
The rotor bearings are protected against ingress of dirt and grass but the rotor should e
checked regularly and if string or other foreign objects get wound around the shaft. These
should be removed immediately.

7

8
PLATE 1 - PARTS LIST - MAINFRAME
Position
Part No
Qty.
Description
1
WX-11079
1
Mainframe
2
WX-1560
1
Engine (Honda)
3
WX-26401
1
Fastening Set
4
WX-11179
1
Hopper
5
WX-3430
1
Winch
6
WX-9503
1
Fastening Set
7
WX-3530
1
Winch Strap
8
WX-9603
1
Fastening Set
9
WX-2820
1
Support Tube
10
WX-2666
2
Hopper Trunion
11
WX-9703
2
Fastening Set
12
WX-0441
1
Hopper Bearing
13
WX-26001
1
Fastening Set
14
WX-9878
1
Hopper Guard Rail
15
WX-9903
1
Fastening Set
16
WX-1626
1
Tee Knob
17
WX-1726
1
Shoot Bolt
18
WX-3625
1
Spring
19
WX-3722
1
Roll Pin
20
WX-1352
2
Wheel (complete)
21
WX-B5551
2
Tube
22
WX-B5351
2
Tyre
23
WX-4951
2
Hub Cap
24
WX-1538
2
Wheel Bearing - Inner
25
WX-1638
2
Wheel Bearing - Outer
26
WX-0645
2
Oil Seal
27
WX-10078
2
Skirt
28
WX-10203
2
Fastening Set
29
WX-0341
2
Rotor Bearing
30
WX-10803
2
Fastening Set
31
WX-1676
1
Front Brush
32
WX-10703
1
Fastening Set
33
WX-12677
1
Belt Guard
34 WX-26201
1
Fastening Set
35 WX-13880
1
Height Adjuster
36 WX- 0503
1
Fastening Set
37 WX-10253
1
Front Wheel Mount
38 WX-26101
1
Fastening Set
39 WX-13151
2
Wheel Fork
40 WX-1520
2
Special Washer
41 WX-6303
2
Fastener Set
42 WX-4252 2 Mk I Front Wheel (Takes 1 inch axle)
43 WX-4451 2 Mk I Wheel Axle (1inch)
44 WX-4551 4 Front Axle Spacer
42 WX-4352 2 MK II Front Wheel (Takes 12mm axle)
42 WX-4552 2 MK III Front Wheel (White with solid Tyre)
43 WX-6003 2 MK II/III Wheel Axle (12mm)

9

10
PLATE 2 - PARTS LIST - BRUSH ROTOR
Position
ATC 120
Part No.
Qty
ATX 120
Part No.
Qty
Description
1
WX-11066
1
WX-11066
1
Brush Rotor
2
WX-5001
4
WX-5001
4
Fastening Set
3
WX-6262
1
WX-6262
1
Pulley
4
WX-0147
2
WX-0147
2
Key
5
WX-6362
1
WX-6362
1
Taper Lock
6
WX-3634
2
WX-3634
2
Drive Belt
7
WX-6462
1
WX-6462
1
Pulley
8
WX-6562
1
WX-6562
1
Taper Lock
9
WX-2870
8
WX-7570
8
Brush Strip
10
WX-1862
1
WX-1862
1
Jockey Pulley
12
WX-1438
2
WX-1438
2
Jockey Bearings
13
WX-0622
2
WX-0622
2
Circlip
14
WX-0722
1
WX-0722
1
Circlip
15
WX-2466
1
WX-2466
1
Jockey Bracket
16
WX-0425
1
WX-0425
1
Spring
17
WX-1738
1
WX-1738
1
Bush
18
WX-2566
1
WX-2566
1
Pivot
19
WX-0715
1
WX-0715
1
Washer

11
PLATE 3 - PARTS LIST - DRAWBAR ASSEMBLY
Position
Part No.
Qty
Description
1
WX-12880
1
Drawbar
2
WX-4503
1
Fastener Set
3
WX-2356
1
Tow Hitch
4
WX- 1503
1
Fastening Set
5
WX- 12156
1
Tow Hitch Swivel
6
WX-1403
1
Fastening Set

12
PLATE 4 - PARTS LIST - TINE SET, OPTION
Position
Part No.
Qty
Description
1
WX-7158
2
Tine Bracket
2
WX-7258
2
Tine Bar
3
WX-3125
8
Tine
4
WX-11303
2
Fastener Set
5
WX-26301
2
Fastener Set
6
WX-0121
2
R Clip
7
WX-1128
2
Retaining Pin

13
SAFETY LABELS
1
GB
F
D
ATTENTION DESCRIPTION OF PICTOGRAMS
ATTENTION DESCRIPTION DES PICTOGRAMES
VORSICH BESCHREIGUNG DER PIKROGRAMMEN
2
GB
F
D
Do not use without p.t.o. sharft guard.
Ne pas utilise sans le dipositif de sûreté de I’arbre p.t.o. (arbre
d’entraînement).
Nicht benutsen ohne p.t.o. (antriebswelle) schutzvorrichtung
3
GB
F
D
Never remove guards or attempt adjustment until rotor has stopped.
Ne pas enlever ni les dispositifsde sûreté ni essayer le regal ge avant que le
rotor s’arrête.
Schutzvorrichtung niemal abnehmen oder einstellung versuchen, bevore der
rotor abstellt.
4
GB
F
D
Read operating manual before use.
Lisez Manual D’Opéreation avant l’utilisation.
Vor der, Bentriebshandbuch lessen.
5
GB
F
D
Ear defenders must be worn.
Des serre-têtes doivent être portés.
Ohrenschützer müβen getragen warden.
6
GB
F
D
Bystanders must be at least 20 metres from machine range of action.
Des spectateurs doivent s’écarter au moins metres du rayon d’action de la
machine.
Umstenhenden müβen sich mindestens 20 meter vom
maschinenbetriebsraum entfernen.
1
v
v
b
2
1
3
4
5
6

14
1
GB
F
D
Protective eyewear, footwear, gloves and ear protectors must
be worn.
Lunettes de protection, chaussures, gants, protégés-oreilles doivent être
portèes.
Schutzbrille, schuhe, handschuhe une Gerhörschutz getragen warden muss.
2
GB
F
D
ATTENTION DESCRIPTION OF PICTOGRAMS
ATTENTION DESCRIPTION DES PICTOGRAMES
VORSICH BESCHREIGUNG DER PIKROGRAMMEN
3
GB
F
D
Read operating manual before use.
Lisez Manual D’Opéreation avant l’utilisation.
Vor der, Bentriebshandbuch lessen.
1
2
3

15
1
GB
F
D
Keep clear of unpropped body
Reculez de la machine éléeve.
Nicht in die ungeschützte Maschine fassen
2
GB
F
D
Damage to brushes if set too low
Ne montez pas la brosse très bas
Bürsten können beschädigt warden, wenn sie zu tief eingestellt
sind.
3
GB
F
D
Always stop rotor before emptying hopper.
Arrêtez le rotor avant de vider la trémie
Rotor muss vor Entleerung des Behälters zum Stillstand
Kommen.
4
GB
F
D
When scarifying, lift rotor before turning.
À la course de rayer, élevez le rotor avant de tourner la
machine
Beim vertikutieren (Grasnarbe aufreiβen) muss der Rotor vor
Richtungsveränderungen (Kurven) angehoben warden.
5
GB
F
D
Replace brushes when worn to 130mm of bristle.
Remplacez la brosse à 130 mm de longuer de poil.
Die Bürsten sind zu wechseln, wenn die Borsten nur noch
130mm lang sind.
6
GB
F
D
Read operating manual before use.
Livre d’exploitation lire avant tout utilisation.
Less die Bedienungsanleitung vor dem Gebrauch.
1
v
v
b
2
v
b
3
v
b
4
v
v
b
5
v
b
6
v
b

16