Westgate STL2-50W K Series User manual

INSTALLATION INSTRUCTIONS MANUAL
STREET LIGHT
Rev A January 2019
MODELS:
STL2-50W-xxK, STL2-100W-xxK, STL2-150W-xxK, STL2-200W-xxK for 120-277V AC 50/60Hz
STL2-90W-xxK-480V, STL2-150W-xxK-480V, STL2-200W-xxK-480V for 277-480V AC 50/60Hz
Model description: xx=CCT (30=3000K, 40=4000K, 50=5000K, 6=5700K)
SAFETY INSTRUCTION
Read instructions carefully before attempting to install fixture.
Disconnect power before installing or servicing.
This fixture must be wired in accordance with the National Electrical Code and applicable local codes
and ordinances.
All wiring should be performed by a qualified electrician.
Suitable for using in the following
locations:
Ambient Temp: -40~+104°F;Wet Locations
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the
manufacturer or his service agent or a similar qualified person in order to avoid a hazard.
The light source of this luminaire is not replaceable; when the light source reaches its end of life the
whole luminaire shall be replaced.
Retain instruction for future reference.
INSTALLATION –on 1.575”or 2.362”diameter pole
1. Open the back cover. (Fig1)
2. Use tool to loose two screws which were pre-installed on the lamp for fixing lamp to the pole. (Fig.2)
3. Install the lamp on the pole and .(Fig.3)
4. Refer to 0°step, adjust the lamp installation angle up or down(each step is 2.5°), see Fig 4. And ensure the lamp
was safely and firmly fixed .
5. Connect the lamp pole internal cable with the luminaire cable.(Fig.5)
6. Close the back cover, the installation is completed. (Fig.6)
7. According to the lamp inner wiring schematic, connect wires safely(If needed). (Fig.7)
Fig.1 Fig.2 Fig.3 Fig.5 Fig.6
L (BLACK)
N (WHITE)
G ( GREEN)
O°Step
Fig.4
WESTGATE MFG., INC | 2462 E 28th Street, Vernon, CA 90058 USA |1-323-826-9490|[email protected]

Wiring Diagrams
Model number parameter list:
After installation, please
check whether the lighting fixture is firmly fixed.
check whether wires are connected correctly.
At last, turn on the power, and check if the lighting fixture works well. If not, please turn off the power and
contact with local dealer.
MODEL
VOLTAGE
Power
Factor
WATT
CURRENT
Max.
Maximum Weight
STL2-50W-xxK
100-277V AC
>0.9
50W
0.65A
9.5lbs
STL2-100W-xxK 100-277V AC 100W 1.5A 9.9lbs
STL2-90W-xxK-480V
277-480V AC
90W
0.5A
9.9lbs
STL2-150W-xxK 100-277V AC 150W 1.65A 13.7lbs
STL2-150W-xxK-480V 277-480V AC 150W 0.64A 13.7lbs
STL2-200W-xxK 100-277V AC
200W
2.25A
14.7lbs
STL2-200W-xxK-480V
277-480V AC
200W
1.0A
14.7lbs
LED DRIVER
(Brown)
(Blue)
N
Gray -
White +
Line
(Black)
Lout
Neutral
L
(White)
(Red)
Photosensor
L
N
(Black)
L
(White)
N
(Green)
G
N
(Green)
G
SPD(optional)
0-277V AC
277-480V AC
50/60 HZ
LED
(Green)
G
Fig(6)
Fig.7
WESTGATE MFG., INC | 2462 E 28th Street, Vernon, CA 90058 USA |1-323-826-9490|[email protected]