Westinghouse WDC804M5WA User manual

WDC804M5WA
user manual
Tumble Dryer

Electrolux. Thinking of you.
Westinghouse. We are part of the Electrolux family.
Share more of our thinking at www.electrolux.com
CONTENTS
Safety information 2
Conditions of Use 5
Safety instructions 5
Product Description 6
Control Panel 7
Program table 8
Options 9
Settings 11
Before first use 13
Daily use 13
Hints and tips 14
Care and cleaning 15
Troubleshooting 17
Technical Data 20
Warranty 20
Environmental concerns 22
Subject to change without notice.
SAFETY INFORMATION
Before the installation and use of the appliance, carefully
read the supplied instructions. The manufacturer is not
responsible if an incorrect installation and use causes
injuries and damage. Always keep the instructions with the
appliance for future reference.
- Read the supplied instructions.
Children and vulnerable people safety
WARNING!
Risk of suffocation, injury or permanent disability.
•This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
the use of the appliance in a safe way and understand the
hazards involved.
•Children between 3 and 8 years of age and persons with
very extensive and complex disabilities shall be kept away
from the appliance unless continuously supervised.
2 westinghouse

•Children of less than 3 years of age should be kept away
from the appliance unless continuously supervised.
•Do not let children play with the appliance.
•Keep all packaging away from children and dispose of it
appropriately.
•Keep detergents away from children.
•Keep children and pets away from the appliance when the
door is open.
•If the appliance has a child safety device, it should be
activated.
•Children shall not carry out cleaning and user maintenance
of the appliance without supervision.
General Safety
•Do not change the specification of this appliance.
•The appliance can be installed as freestanding or below a
kitchen counter with correct space (refer to the Installation
leaflet).
•Do not install the appliance behind a lockable door, a
sliding door or a door with a hinge on the opposite side,
that would prevent the appliance door from being fully
open.
•The ventilation opening in the base must not be covered
by a carpet, mat, or any floor covering.
•WARNING: The appliance must not be supplied through
an external switching device, such as a timer, or
connected to a circuit that is regularly switched on and off
by a utility.
•Connect the mains plug to the mains socket only at the
end of the installation process. Make sure that the mains
plug is accessible after installation.
•If the mains power supply cable is damaged, it must be
replaced by the manufacturer, its Authorised Service
Centre or similarly qualified persons to avoid an electrical
hazard.
•Do not exceed the maximum load of 8 kg (refer to the
"Programme chart" chapter).
westinghouse 3

•Do not use the appliance if items have been soiled with
industrial chemicals.
•Wipe away lint or packaging debris that has accumulated
around the appliance.
•Do not run the appliance without a filter. Clean the lint filter
before or after each use.
•Do not dry unwashed items in the tumble dryer.
•Items that have been soiled with substances such as
cooking oil, acetone, alcohol, petrol, kerosene, spot
removers, turpentine, waxes and wax removers should be
washed in hot water with an extra amount of detergent
before being dried in the tumble dryer.
•Items such as foam rubber (latex foam), shower caps,
waterproof textiles, rubber backed articles and clothes or
pillows fitted with foam rubber pads should not be dried in
the tumble dryer.
•Fabric softeners, or similar products, should only be used
as specified by the product manufacturer’s instructions.
•Oil-affected items can ignite spontaneously, especially
when exposed to heat sources such as in a tumble dryer.
The items become warm, causing an oxidation reaction in
the oil. Oxidation creates heat. If the heat cannot escape,
the items can become hot enough to catch fire. Piling,
stacking or storing oil-affected items can prevent heat from
escaping and create a fire hazard.
•If it is unavoidable that fabrics that contain vegetable or
cooking oil or have been contaminated by hair care
products be placed in a tumble dryer they should first be
washed in hot water with extra detergent -this will reduce,
but not eliminate, the hazard.
•Remove all objects from items that could be a source of
fire ignition such as lighters or matches.
•WARNING: Never stop a tumble dryer before the end of
the drying cycle unless all items are quickly removed and
spread out so that the heat is dissipated.
•Before any maintenance operation, deactivate the
appliance and disconnect the mains plug from the socket.
4 westinghouse

CONDITIONS OF USE
This appliance is intended to be used in
household and similar applications such
as:
• farm houses;
• by clients in hotels, motels, bed &
breakfast and other residential type
environments;
• areas for communal use in blocks of
flats or in launderettes.
SAFETY INSTRUCTIONS
Installation
• Remove all the packaging.
• Do not install or use a damaged
appliance.
• Follow the installation instructions
supplied with the appliance.
• Always take care when moving the
appliance as it is heavy. Always use
safety gloves and enclosed footwear.
• Do not install or use the appliance
where the temperature can be lower
than 5°C or higher than 35°C.
• The floor area on which the appliance
is to be installed must be flat, stable,
heat resistant and clean.
• Make sure that there is air circulation
between the appliance and the floor.
• Always keep the appliance vertical
when it is being moved.
• The rear surface of the appliance must
be put against a wall.
• When the appliance is in its permanent
position, check if it is levelled correctly
with the aid of a spirit level. If it is not,
adjust the feet accordingly.
Electrical connection
WARNING! Risk of fire and
electric shock.
• The appliance must be earthed.
• Make sure that the parameters on the
rating plate are compatible with the
electrical ratings of the mains power
supply.
• Always use a correctly installed
shockproof socket.
• Do not use multi-plug adapters and
extension cables.
• Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
• Do not touch the mains cable or the
mains plug with wet hands.
Use
WARNING! Risk of injury,
electric shock, fire, burns or
damage to the appliance.
• This appliance is for household
(indoors) use only.
• Do not dry damaged (torn, frayed)
items that contain padding or fillings.
• If laundry has been washed with a stain
remover, carry out an additional rinse
cycle before starting a drying cycle.
• Dry only fabrics that are suitable to dry
in the appliance. Follow the cleaning
instruction on the item label.
• Do not drink or prepare food with the
condensed water/distilled water. It can
cause health problems to people and
pets.
• Do not sit or stand on the open door of
the appliance.
• Do not dry dripping wet clothes in the
appliance.
Care and cleaning
WARNING! Risk of injury or
damage to the appliance.
• Do not use water spray and steam to
clean the appliance.
westinghouse 5

• Clean the appliance with a moist soft
cloth. Use only neutral detergents. Do
not use abrasive products, abrasive
cleaning pads, solvents or metal
objects.
Service
• To repair the appliance contact the
Authorised Service Centre.
• Use original spare parts only.
Disposal
WARNING! Risk of injury or
suffocation.
• Disconnect the appliance from the
mains electrical and water supplies.
• Cut off the mains electrical cable close
to the appliance and dispose of it.
• Remove the door catch to prevent
children or pets from becoming trapped
in the drum.
• Dispose of the appliance in accordance
with local requirements for the disposal
of Waste Electrical and Electronic
Equipment (WEEE).
PRODUCT DESCRIPTION
1 2
5
3
4
6
7
8
9
1Water container
2Control panel
3Appliance door
4Filter
5Rating plate
6Airflow slots
7Heat Exchanger lid
8Heat Exchanger cover
9Adjustable feet
For ease of loading laundry or
ease of installation the door is
reversible. (see separate
leaflet).
6 westinghouse

CONTROL PANEL
1
89 7 6
3
5
4
2
1Program knob
2Display
3Time Dry touch button
4Start/Pause touch button
5Delay Start touch button
6Extra Anticrease touch button
7Gentle Dry touch button
8Dryness Level touch button
9On/Off button
Press the touch buttons with
your finger in the area with the
symbol or name of the option.
Do not wear gloves when you
operate the control panel.
Make sure that the control
panel is always clean and dry.
Display
Symbol on the display Symbol description
time drying option on
delay start option on
indicator: check Heat Exchanger
westinghouse 7

Symbol on the display Symbol description
indicator: clean filter
indicator: drain the water container
indicator: drying phase
indicator: cooling phase
indicator: anti-crease phase
child lock on
wrong selection
program duration
- time Drying duration
- delay start duration
PROGRAM TABLE
Program Load
1)
Properties / Fabric type
2)
Favourite
Depends
on a
memo‐
rised pro‐
gram
You can do your configuration of program and op‐
tions and memorise in the appliance memory
(See chapter " Settings - Favourite ").
Cotton 8 kg Cotton fabrics. /
Mixed 3kg
Cotton and synthetic fabrics. Low
temperature program. Delicate pro‐
gram with warm air.
/
Bedding 3kg
Bed linen such as single and dou‐
ble sheets, pillowcases, duvet cov‐
er.
/
Synthetic 3,5 kg Synthetic and mixed fabrics. /
Eco Cotton
3)
8 kg
Cycle to be used to dry cotton with
"cotton cupboard" dryness level,
with maximum energy saving.
/
Refresh 1kg Refreshing textiles that were in storage.
8 westinghouse

Program Load
1)
Properties / Fabric type
2)
Denim 4 kg
Leisure clothing such as jeans,
sweat-shirts of different material
thicknesses (e.g. at the neck, cuffs
and seams).
/
Gym Wear 2 kg Sportswear, thin and light fabrics,
microfiber, polyester.
/
Easy Iron 1 kg (or 5
shirts)
Easy care fabrics for which a mini‐
mum of ironing is necessary. The
drying results can be different from
one type of fabric to another.
Shake the items before putting
them in the appliance. When the
program has ended, immediately
remove the items and put them on
a hanger.
/
Shirts 1,5kg (or
7 shirts)/
Easy care fabrics for which a mini‐
mum of ironing is necessary. The
drying results can be different from
one type of fabric to the other.
Shake the items before you put
them in the appliance. When the
program is completed, Immediately
remove the items and put them on
a hanger.
/
Wool 1 kg
Woollen fabrics. Gentle drying for hand-washable
woollens. Remove items immediately when the
program is completed.
Delicates 4 kg Delicate fabrics such as viscose,
rayon, acrylic, and their blends.
/
1) The maximum weight refers to dry items.
2) For fabric mark meaning see chapter HINTS AND TIPS: Preparing the laundry.
3) Eco Cotton program is the reference program for Energy Label, tested according to AS/NZS2442.2.
OPTIONS
Dryness Level
This function helps to increase dryness of
the laundry. There are 3 options:
• Extra Dry
• Cupboard Dry
• Iron Dry
Gentle Dry
With this option you can set a delicate
drying program that has a low
temperature. Use this option with a fabrics
that have the symbol on the fabric label
(e.g. acrylic, viscose).
westinghouse 9

Extra Anticrease
Extends the anti-crease phase by 60
minutes at the end of the drying cycle.
This function reduces creases. The
laundry can be removed during the anti-
crease phase.
Time Dry
You can set the program duration, from a
minimum of 10 minutes to a maximum of 2
hours. The required duration is related to
the quantity of laundry in the appliance.
We recommend that you set a
short duration for small
quantities of laundry or for only
one item.
TIME DRYING RECOMMENDATION
10 - 20 min
action of cool
air only (no
heater).
TIME DRYING RECOMMENDATION
20 - 40 min
additional dry‐
ing to improve
dryness after
previous dry‐
ing cycle.
>40 min
full drying of
the small laun‐
dry loads up to
4 kg, well
spun (>1200
rpm).
Options table
Program
1)
Dryness Level Gentle Dry Extra Anti‐
crease Time Dry
Favourite Depends on a memorised program
Cotton ■ ■ ■ ■ ■ ■
Mixed ■ ■ ■ ■
Bedding ■ ■ ■ ■
Synthetic ■ ■ ■ ■ ■ ■
Eco Cotton ■ ■
Refresh ■
Denim ■ ■ ■
Gym Wear ■ ■
Easy Iron ■ ■ ■
Shirts ■ ■
Wool ■
10 westinghouse

Program
1)
Dryness Level Gentle Dry Extra Anti‐
crease Time Dry
Delicates ■ ■ ■
1) Together with the program you can set 1 or more options. To activate or deactivate them, press the related
touch button.
SETTINGS
A B C
EDF
A. Time Dry touch button
B. Start/Pause touch button
C. Delay Start touch button
D. Extra Anticrease touch button
E. Gentle Dry touch button
F. Dryness Level touch button
Child lock function
This option prevents children playing with
the appliance while a program is
operating. The touch buttons are locked.
Only the on/off button is unlocked.
Activating the child lock option:
1. Press the on/off button to activate the
appliance.
2. Press and hold touch button (D) for a
few seconds.
The child lock indicator comes on.
It is possible to deactivate the
child lock option while a
program operates. Press and
hold the same touch buttons
until the child lock indicator
goes off. The Child Lock
function isn't available for 8 s
after switching on the
appliance.
Favourite
You can do your configuration of program
and options and memorise in the
appliance memory.
To memorise your
configuration:
1. Press the on/off button to activate the
appliance
2. Set the program and available options.
3. Press the (E) button for some
seconds.
The sound and the message on the
display confirm that the configuration is
memorised.
To activate your memorised
configuration:
1. Press the on/off button to activate the
appliance.
2. Use the program knob to set Favourite
position.
Previously memorised configuration of
program and options will be restore.
Adjustment of remaining
laundry moisture
The appliance allows you to chose
between 3 levels corresponding to
different ranges of water hardness.
westinghouse 11

Dryness
level ppm
the results
from the inclu‐
ded water
hardness kit.
< 150 C01-C03
150 -
300
C04-C05
> 300 C06-C07
Depending on the country, the water
hardness is expressed in equivalent
scales: e.g. French degrees (°f), German
degrees (°d), English degrees (°e), mmol/l
and ppm
If necessary, please contact your local
water authority to check the water
hardness in your area.
Every time you enter in the
"Adjustment of remaining
laundry moisture" mode,
previously set degree of
remaining moisture will change
into next value ( e.g previously
set will change into
).
To change the default degree of remaining
moisture:
1. Press the on/off button to activate the
appliance.
2. Use the program knob to set any
program.
3. Wait approximately 8 seconds.
4. Press and hold buttons (E) and (D) at
the same time.
One of these indicators comes on:
• the maximum dryness
• the more dry laundry
• the standard dry laundry
5. Press and hold buttons (E) and (D)
again until the indicator of the correct
level comes on.
If the display returns to the
normal mode (the time of
the selected program from
step 2. will be displayed),
while setting the degree of
remaining moisture, press
and hold buttons (E) and
(D) once again to enter to
the "Adjustment of
remaining laundry moisture"
mode (previously set
degree of remaining
moisture will change into
next value).
6. After 5 s the display returns to normal
mode.
Water container indicator
By default, the water container indicator is
on. It comes on when the program is
completed or when it is necessary to
empty the water container.
If a draining kit is installed
(additional accessory), the
appliance automatically drains
the water from the water
container. In this case we
recommend that you deactivate
the indicator of the water
container.
Deactivating the water container
indicator:
1. Press the on/off button to activate the
appliance.
2. Wait approximately 8 seconds.
3. Press and hold touch buttons (A) and
(C) at the same time.
The display shows one of these 2
configurations:
• The display shows "Off". After 5 s
the display returns to normal mode.
• The display shows "On". After 5 s
the display returns to normal mode.
Buzzer on/off
To deactivate or activate the acoustic
signals, press and hold for approximately
12 westinghouse

2 seconds touch buttons (E) and (F) at the
same time.
BEFORE FIRST USE
Before you use the appliance to dry
items:
• Clean the tumble dryer drum with a
moist cloth.
• Start a 1 hour program with moist
laundry.
DAILY USE
Start a program without delay
start
1. Prepare the laundry and load the
appliance.
CAUTION! Make sure that
when you close the door,
the laundry does not get
caught between the
appliance door and the
rubber seal.
2. Press the on/off button to activate the
appliance.
3. Set the correct program and options
for the type of load.
The display shows the program duration.
Real drying time will depend on
type of the load (quantity and
composition), the room
temperature and the humidity
of your laundry after spin drying
phase.
4. Press the Start/Pause touch button.
The program starts.
Starting the program with delay
start
1. Set the correct program and options
for the type of load.
2. Press the delay start button again and
again until the display shows the delay
time you want to set.
You can delay the start of a
program from a minimum of
30 minutes to a maximum
of 20 hours.
3. Press the Start/Pause touch button.
The display shows the countdown of the
delay start.
When the countdown is completed, the
program starts.
Change a program
1. Press the on/off button to deactivate
appliance
2. Press the on/off button to activate the
appliance.
3. Set the program.
At the end of the program
When the program is completed:
• An intermittent acoustic signal
operates.
• The display shows
• The indicator is on.
• The indicators Filter and Tank
may come on.
• The Start/Pause indicator is on.
The appliance continues to operate with
the anti-crease phase for approximately
westinghouse 13

30 minutes or more if Extra Anticrease
option was set (see chapter Option - Extra
Anticrease ).
The anti-crease phase reduces creasing.
You can remove the laundry before the
anti-crease phase is completed. We
recommend, for better results, that you
remove the laundry when the phase is
almost completed.
When the anti-crease phase is completed:
• The display still shows
• The indicator is off.
• The indicators Filter and Tank
remain on.
• Start/Pause indicator goes off.
1. Press the on/off button to deactivate
the appliance.
2. Open the appliance door.
3. Remove the laundry.
4. Close the appliance door.
Possible causes of unsatisfactory drying
results:
• Inadequate default dryness level
settings. See chapter Adjustment of
default dryness level
Always clean the filter and
empty the water container
when a program is
completed.
Stand-by function
To reduce energy consumption, this
function automatically deactivates the
appliance:
• After 5 minutes if you do not start the
program.
• After 5 minutes from the end of the
program.
HINTS AND TIPS
Preparing the laundry
Very often the clothes after
washing cycle are kneaded and
tangled altogether.
Drying kneaded and tangled
clothes is inefficient.
To assure proper air flow and
even drying it is recommended
to shake and load one by one
the clothes to the tumble dryer.
To assure proper drying process:
• Close the zips.
• Close the fasteners of duvet covers.
• Do not dry ties or ribbons loose (e.g.
apron ribbons). Tie them before you
start a program.
• Remove all items from pockets.
• Turn items with the internal layer made
of cotton inside out. Cotton layer must
be faced outwards.
• Always set the program suitable for the
type of laundry.
• Do not put light and dark colours
together.
• Use suitable program for cottons,
jersey and knitwear to reduce
shrinkage.
• Do not exceed the maximum load
stated in the programs chapter or
shown on the display.
• Dry only the laundry that is suitable for
tumble drying. Refer to the fabric label
on the items.
• Do not dry large and small items
together. Small items can be trapped
inside the large items and remain wet.
• Shake the large clothes, fabrics before
placing in the tumble dryer. It is to
avoid moist places inside the fabric
after the drying cycle.
14 westinghouse

Fabric label Description
Laundry is suitable for tumble drying.
Laundry is suitable for tumble drying at higher temperatures.
Laundry is suitable for tumble drying at low temperatures only.
Laundry is not suitable for tumble drying.
CARE AND CLEANING
Cleaning the filter
CAUTION! Avoid the use of
water to clean the filter. Instead
throw away lint in the dustbin
( avoid dispersion of plastic
fiber in water ambient).
To achieve the best drying
performances clean the filter
regularly , clogged filter lead to
longer cycles and energy
consumption increase.
Use your hand to clean the
filter , and if necessary , a
vacuum cleaner .
1. 2.
1
2
3. 4.
5.
1)
6.
2
1
1) If necessary remove fluff from the filter socket and gasket. You can use a vacuum cleaner.
westinghouse 15

Emptying the water container
1. 2.
3. 4.
You can use the water from the
water container as an
alternative to distilled water
(e.g. for steam ironing). Before
you use the water, remove dirt
residues with a filter.
Cleaning the Heat Exchanger
1. 2.
3. 4.
2
1
1
16 westinghouse

5. 6.
7. 8.
2
2
1
9. 10.
Cleaning the drum
WARNING! Disconnect the
appliance before you clean it.
Use a standard neutral soap detergent to
clean the inner surface of the drum and
drum lifters. Dry the cleaned surfaces with
a soft cloth.
CAUTION! Do not use
abrasive materials or steel wool
to clean the drum.
Cleaning the control panel and
housing
Use a standard neutral soap detergent to
clean the control panel and housing.
Use a moist cloth to clean. Dry the
cleaned surfaces with a soft cloth.
CAUTION! Do not use furniture
cleaning agents or cleaning
agents which can cause
corrosion.
Cleaning the airflow slots
Use a vacuum cleaner to remove fluff from
the airflow slots.
TROUBLESHOOTING
WARNING! Refer to Safety
chapters.
westinghouse 17

Error Codes
The appliance does not start or it stops during operation.
First try to find a solution to the problem (refer to the table). If the problem persists,
contact the Authorised Service Centre.
WARNING! Deactivate the appliance before carrying out any check.
In case of major problems, the acoustic signals operate, the display shows an
error code and the Start/Pause button may flash continuously:
Error code Possible cause Remedy
E5A
Appliance motor overloaded.
Too much laundry or entrap in the
drum.
The program was not completed.
Remove the laundry from the
drum, set the program and restart
the cycle.
E97
Internal fail. No communication be‐
tween electronic elements of the
appliance.
The program was not finished
properly or the appliance stoped
too early. Switch the appliance off
and on again.
If the error code appears again,
contact the Authorised Service
Centre.
EH0
The mains supply is unstable. When the appliance is showing
EH0, please wait until main supply
is stable than press start. If the ap‐
pliance pause the cycle without
any indication then press the cycle
start. If the warning will occur
check the power cord / socket in‐
tegrity or main supply.
If the display shows other error codes, deactivate and activate the appliance. If the
problem continues, contact the Authorised Service Centre.
In case of different problem with the tumble dryer check the table below for possible
solutions.
Troubleshooting
Problem Possible solution
You cannot activate the appliance. Make sure that the mains plug is connected
to the mains socket.
Check fuse in fuse box (domestic installa‐
tion).
The program does not start. Press Start/Pause.
18 westinghouse

Problem Possible solution
Make sure that the appliance door is closed.
The appliance door does not close. Make sure that the installation of the filter is
correct.
Make sure that the laundry is not caught be‐
tween the appliance door and the rubber
seal.
The appliance stops during operation. Make sure that the water container is empty.
Press Start/Pause to start the program again.
Load is too small, increase the load or use
the Time Drying program.
The cycle time is too long or unsatisfactory
drying result.
1)
Make sure that the weight of the laundry is
suitable for the duration of the program.
Make sure that the filter is clean.
The laundry is too wet. Spin the laundry in
the washing machine again.
Ensure that the room temperature is higher
than +5°C and lower than +35°C. Optimal
room temperature is 18°C to 25°C.
Set the Time Drying or the Extra Dry pro‐
gram.
2)
The display shows . If you want to set a new program, deactivate
and activate the appliance.
Make sure that the options are suitable for
the program.
1) After maximum 6 hours, the program ends automatically.
2) It can happen that some area remains humid when drying big items (e.g. bed sheets ).
If the drying results are not
satisfactory
• The set program was incorrect.
• The filter is clogged.
• The Heat Exchanger is clogged.
• There was too much laundry in the
appliance.
• The drum is dirty.
• Incorrect setting of the conductivity
sensor ( See chapter " Settings -
Adjustment of the remaining laundry
moisture degree " for better setting).
• The airflow slots are clogged.
• Room temperature is too low or too
high ( optimal room temperature 18°C
to 25°C )
westinghouse 19

TECHNICAL DATA
Height x Width x Depth 850 x 596 x 630 mm (maximum 659 mm)
Max. depth with the appliance door open 1104 mm
Max. width with the appliance door open 958 mm
Adjustable height 850 mm (+ 15 mm - feet adjustment)
Drum volume 118 l
Maximum load 8 kg
Voltage 230-240 V
Frequency 50 Hz
Total power 2250 W
Type of use Household
Permitted ambient temperature + 5°C to + 35°C
Level of protection against ingress of solid
particles and moisture ensured by the protec‐
tive cover, except where the low voltage
equipment has no protection against mois‐
ture
IPX4
WARRANTY
FOR SALES IN AUSTRALIA AND NEW
ZEALAND
APPLIANCE: ELECTROLUX DRYER
This document sets out the terms and
conditions of the product warranties
for Electrolux Appliances. It is an
important document. Please keep it
with your proof of purchase documents
in a safe place for future reference
should there be a manufacturing defect
in your Appliance. This warranty is in
addition to other rights you may have
under the Australian Consumer Law.
1. In this warranty:
a) ‘ACL’ or ‘Australian Consumer
Law’ means Schedule 2 to the
Competition and Consumer Act
2010;
b) ‘Appliance’ means any Electrolux
product purchased by you and
accompanied by this document;
c) ‘ASC’ means Electrolux authorised
service centres;
d) ‘Electrolux’ is the brand controlled
Electrolux Home Products Pty Ltd
of 163 O’Riordan Street, Mascot
NSW 2020, ABN 51 004 762 341
in respect of Appliances purchased
in Australia and Electrolux (NZ)
Limited (collectively “Electrolux”) of
3-5 Niall Burgess Road, Mount
Wellington, in respect of
Appliances purchased in New
Zealand;
e) ‘Warranty Period’ means the
period specified in clause 3 of this
warranty;
f) ‘you’ means the purchaser of the
Appliance not having purchased
the Appliance for re-sale, and
‘your’ has a corresponding
meaning.
2. Application: This warranty only
applies to new Appliances, purchased
and used in Australia or New Zealand
20 westinghouse