Westinghouse Gen9500DF User manual

USER MANUAL
WGen9500DF
Portable Generator
Gasoline: 9500 Running Watts | 12500 Peak Watts
Propane: 8500 Running Watts | 11200 Peak Watts
REMOTE START

2 | Westinghouse Outdoor Power Equipment
DISCLAIMERS:
All information, illustrations and specications in this manual are based on the latest information available at the time of
publishing. The illustrations used in this manual are intended as representative reference views only. Moreover, because
of our continuous product improvement policy, we may modify information, illustrations and/or specications to explain
and/or exemplify a product, service or maintenance improvement. We reserve the right to make any change at any time
without notice. Some images may vary depending upon which model is shown.
ALL RIGHTS RESERVED:
No part of this publication may be reproduced or used in any form by any means – graphic, electronic or mechanical,
including photocopying, recording, taping or information storage and retrieval systems – without the written permission
of Westinghouse Outdoor Power Equipment.
DANGER
This manual contains important instructions for operating this generator. For your safety
and the safety of others, be sure to read this manual thoroughly before operating the
generator. Failure to properly follow all instructions and precautions can cause you and
others to be seriously hurt or killed.
Model
Number
Running
Watts
Peak
Watts
Fuel
Tank
Size
(L/G)
Rated
Speed
(RPM)
Ignition
Type
Spark
plug
Engine
Disp (cc)
Stroke X
Bore
Oil
Capacity
(L) Oil Type THD
WGen9500DF Gas:
9500
LPG:
8500
Gas:
12500
LPG:
11200
25/6.6 3600 TCI F7TC 457 68.8X92 1.10 10W30 <23%
NOTICE
Even with a carburetor modication, engine horsepower will decrease about 3.5% for each 300 meter (1,000 foot) increase in altitude. The
eect of altitude on horsepower will be greater if no carburetor modication is made. A decrease in engine horsepower will decrease the
power output of the generator. Contact our service team to order altitude kits.
FOR YOUR RECORDS:
Date of Purchase:
Generator Model Number:
Purchased from Store/Dealer:
Generator Serial Number:
WGen9500DF TECHNICAL SPECIFICATIONS
HAVE QUESTIONS? Email us at [e-mail] or call 1-855-944-3571
Operating, servicing and maintaining this equipment can expose you to chemicals including engine exhaust,
carbon monoxide, phosphates, and lead, which are known to the State of California to cause cancer and birth
defects or other reproductive harm. To minimize exposure, avoid breathing exhaust, do not idle the engine
except as necessary, service your equipment in a well-ventilated area and wear gloves or wash your hands
frequently when servicing your equipment. For more information go to www.P65Warnings.ca.gov.
WARNING

Westinghouse Outdoor Power Equipment | 3
IMPORTANT: KEEP YOUR PURCHASE RECEIPT TO ENSURE TROUBLE-FREE
WARRANTY COVERAGE.
PRODUCT REGISTRATION
To ensure trouble-free warranty coverage, it is important you register your Westinghouse generator.
You can register your generator by either:
1. Filling in the product registration form below and mailing to:
Product Registration
Westinghouse Outdoor Power Equipment
777 Manor Park Drive
Columbus, Ohio 43228
2. Registering your product Online at wpowereq.com/register
To register your generator you will need to locate the serial number:
WESTINGHOUSE PRODUCT REGISTRATION FORM
PERSONAL INFORMATION GENERATOR INFORMATION
First Name: _______________________________________ Model Number: _____________________________________
Last Name: _______________________________________ Serial Number:______________________________________
Street Address: ___________________________________ Date Purchased: ____________________________________
Street Address: ___________________________________ Purchased From:____________________________________
City, State, ZIP: ____________________________________
Country: __________________________________________
Phone Number: ___________________________________
E-Mail: ___________________________________________
Made in China/ Fabriqu é en Chine
MWE Investments LLC
Columbus Ohio 43228 USA
Con u à columbus , Ohio,tats-Unis
MWE Investments LLC
Columbus Ohio 43228 Etats-Unis
Par t N0.
Numéro de
pièc e
Designed in Columbus , Ohio USA
WHERE IS MY SERIAL NUMBER?
SERIAL NUMBER

4 | Westinghouse Outdoor Power Equipment
TABLE OF CONTENTS
WGEN9500DF TECHNICAL SPECIFICATIONS .....2
PRODUCT REGISTRATION .....................3
Locate Serial Number .......................3
Product Registration .......................3
Product Registration Form ...................3
SAFETY .....................................5
Safety Denitions ..........................5
Safety Symbol Denitions ...................5
General Safety Rules ........................6
Safety Labels and Decals ....................7
Fuel Safety ................................9
UNPACKING .................................10
What Comes in the Box ......................10
Wheel Kit Accessories Box ...................10
ASSEMBLY .................................11
Installing Wheels and Feet ....................11
Installing the Battery ........................12
FEATURES .................................13
Generator Features .........................13
Control Panel Features .....................15
OPERATION .................................16
Before Starting the Generator .................16
Altitude Conversion Kit ......................16
Power Cord ..............................17
Using Extension Cords ...................17
Using Westinghouse Power Cord ...........17
Transfer Switch Connections ..................18
How to Float the Neutral ..................18
Engine Fluids and Fuel .......................18
Adding Gasoline to the Fuel Tank ...........19
Connecting Propane Tank ..................19
Connecting to Large Propane Tank ..........20
Switching Fuel Sources ......................20
How to Pair Remote Key Fob .................21
Power Output and Demand ...................21
Starting the Generator ......................22
Electric Start ............................22
Starting on Gasoline ......................22
Starting on Propane ......................22
Manual Start ............................23
Stopping the Generator ......................23
Normal Operation .......................23
During an Emergency ....................23
MAINTENANCE ..............................24
Maintenance Schedule ......................24
Inspecting and Cleaning the Spark Arrestor ......25
Draining the Carburetor Float Bowl .............25
Engine Oil Maintenance .....................26
Engine Oil Specication ...................26
Checking Engine Oil .....................26
Adding Engine Oil .......................26
Changing Engine Oil .....................27
Air Filter Maintenance .......................27
Cleaning the Air Filter ....................27
Spark Plug Maintenance .....................28
Checking and Adjusting Valve Lash ..............29
Testing GFCI Outlets ........................29
Battery Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
How to Use Battery Charger ................30
Battery Replacement .....................30
Cleaning the Generator ......................30
Storage ..................................30
TROUBLE SHOOTING .........................31
SCHEMATICS ................................33
WGen9500DF Schematic ....................33
EXPLODED AND ENGINE VIEWS ................34
WGen9500DF Exploded View .................34
WGen9500DF Exploded View Part Numbers .....35
WGen9500DF Engine View ...................36
WGen9500DF Engine View Part Numbers ........37

Westinghouse Outdoor Power Equipment | 5
SAFETY DEFINITIONS
The words DANGER, WARNING, CAUTION and
NOTICE are used throughout this manual to highlight
important information. Be certain that the meanings of
these alerts are known to all who work on or near the
equipment.
This safety alert symbol appears
with most safety statements. It
means attention, become alert, your
safety is involved! Please read and
abide by the message that follows
the safety alerts symbol.
DANGER
Indicates a hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING
Indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION
Indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE
Indicates a situation which can cause damage
to the generator, personal property and/or the
environment, or cause the equipment to operate
improperly.
NOTE: Indicates a procedure, practice or condition
that should be followed in order for the
generator to function in the manner
intended.
SAFETY
SAFETY SYMBOL DEFINITIONS
Explosion Hazard
Fire Hazard
Electrical Shock Hazard
Lifting Hazard
Pinch-Point Hazard
Read Manufacturer’s Instructions
Read Safety Messages
Before Proceeding
Wear Personal Protective
Equipment (PPE)
Safety Alert Symbol
Asphyxiation Hazard
Burn Hazard
Burst/Pressure Hazard
Don’t leave tools in the area
Symbol Description

6 | Westinghouse Outdoor Power Equipment
DANGER
Never use the generator in a location that is wet or damp. Never expose the generator to rain, snow, water
spray or standing water while in use. Protect the generator from all hazardous weather conditions. Moisture
or ice can cause a short circuit or other malfunction in the electrical circuit.
Never operate the generator in an enclosed area. Engine exhaust contains carbon monoxide. Only operate
the generator outside and away from windows, doors and vents.
WARNING
Voltage produced by the generator could result in death or serious injury.
• Never operate the generator in rain or a ood plain unless proper precautions are taken to avoid
being subject to rain or a ood.
• Never use worn or damaged extension cords.
• Always have a licensed electrician connect the generator to the utility circuit.
• Never touch an operating generator if the generator is wet or if you have wet hands.
• Never operate the generator in highly conductive areas such as around metal decking or steel works.
• Always use grounded extension cords. Always use three-wire or double-insulated power tools.
• Never touch live terminals or bare wires while the generator is operating.
• Be sure the generator is properly grounded before operating.
WARNING
Gasoline and gasoline vapors are extremely ammable and explosive under certain conditions.
• Always refuel the generator outdoors, in a well-ventilated area.
•Never remove the fuel cap with the engine running.
•Never refuel the generator while the engine is running. Always turn engine o and allow the generator
to cool before refueling.
• Only ll fuel tank with gasoline.
•Keep sparks, open ames or other form of ignition (such as match, cigarette, static electric source)
away when refueling.
•Never overll the fuel tank. Leave room for fuel to expand. Overlling the fuel tank can result in a
sudden overow of gasoline and result in spilled gasoline coming in contact with HOT surfaces.
Spilled fuel can ignite. If fuel is spilled on the generator, wipe up any spills immediately. Dispose of
rag properly. Allow area of spilled fuel to dry before operating the generator.
• Wear eye protection while refueling.
• Never use gasoline as a cleaning agent.
•Store any containers containing gasoline in a well-ventilated area, away from any combustibles or
source of ignition.
• Check for fuel leaks after refueling. Never operate the engine if a fuel leak is discovered.
WARNING
Never operate the generator if powered items overheat, electrical
output drops, there is sparking, ames or smoke coming from the
generator, or if the receptacles are damaged.
Never use the generator to power medical support equipment.
Always remove any tools or other service equipment used during
maintenance from the generator before operating.
NOTICE
Never modify the generator.
Never operate the generator if it
vibrates at high levels, if engine
speed changes greatly or if the
engine misres often.
Always disconnect tools or
appliances from the
generator before starting.
GENERAL SAFETY RULES
SAFETY

Westinghouse Outdoor Power Equipment | 7
SAFETY
SAFETY LABELS AND DECALS
4
5
1
1
34
2
Made in China/ Fabriqu é en Chine
MWE Investments LLC
Columbus Ohio 43228 USA
Con u à columbus , Ohio,tats-Unis
MWE Investments LLC
Columbus Ohio 43228 Etats-Unis
Par t N0.
Numéro de
pièc e
Designed in Columbus , Ohio USA
3
25
5
6
SERIAL NUMBER
64

8 | Westinghouse Outdoor Power Equipment
SAFETY
SAFETY LABELS AND DECALS
9
10
8
11
12
910
7
7
8
12
5
11

Westinghouse Outdoor Power Equipment | 9
When transporting or servicing the generator:
• Make certain the fuel shuto valve is o and the fuel
tank is empty.
• Make sure the LPG tank and LPG hose is not attached
to the generator.
• Disconnect the spark plug wire.
When storing the generator:
• Store away from sparks, open ames, pilot lights, heat
and other sources of ignition.
• Do not store gas or LPG tank near furnaces, water
heaters or any other appliances that produce heat or
have automatic ignitions.
CAUTION
Only use approved LPG tanks with OPD
(overlling prevention device) valve.
Always keep the tank in a vertical position
with the valve on top and installed at
ground level on a at surface. Do not allow
tanks to be around any heat source and
make sure it is not exposed to the sun,
rain and dust. When transporting and
storing, turn o the tank valve and fuel
valve, and disconnect the tank. Make sure
to always cover the generator and tank
outlet with protective plastic caps.
CAUTION
Do not allow children to tamper or
play with the propane tank or hose
connections.
WARNING
If there is a strong smell of propane while
operating the generator close the valve on
the propane tank immediately. Once the
propane is o, use soapy water to check
for leaks on the hose and connections on
the tank valve and the generator. Do not
smoke or light a cigarette or check for
leaks using any open ame source such
as a match or lighter. If a leak is found
contact a qualied technician to inspect
and repair the LPG system before using
the generator.
DANGER
Gasoline and liquid petroleum gas (LPG)
are highly explosive and ammable.
Explosions and re can cause severe
burns or death.
Gasoline and gasoline vapor (Gas)
• Gasoline is highly ammable and explosive.
• Gas expands and contracts with dierent temperatures.
• In case of a gas re, do not attempt to extinguish the
ame if the fuel shuto valve is in the on position.
Introducing an extinguisher to a generator with an open
fuel valve could create an explosion hazard.
• Gas has a distinctive odor, this will help detect potential
leaks quickly.
• Gas vapors can cause a re if ignited.
• Gasoline is a skin irritant and needs to be cleaned up
immediately if it comes in contact with the skin.
Liquid Petroleum Gas (Propane/LPG)
• LPG/Propane is highly ammable and explosive.
• Flammable gas under pressure can cause a re or
explosion if ignited.
• LPG/Propane can settle in low places because it is
heavier than air.
• LPG/Propane has a distinctive odor added to help
detect potential leaks.
• Always keep LPG/Propane tank in an upright position.
• When exchanging LPG/Propane tanks, be sure the tank
value is the same type.
• In case of a LPG/Propane re, do not attempt to
extinguish unless the fuel supply can be shut o.
• LPG/Propane will burn the skin. Prevent skin contact at
all times.
WARNING
Never use a gas container, LPG
connector hose, LPG tank or any other
fuel item that appears to be damaged.
When starting generator:
• Make sure that the gas cap, air lter, spark plug, fuel
lines and exhaust system are properly in place.
• If you spill any gasoline on the tank, allow it to fully
evaporate before operating.
• Make sure the generator and propane tank are on a at
surface before operating.
• If there is a propane odor do not start the unit because
there may be a potential leak.
• Never place propane tank near engine exhaust.
SAFETY
FUEL SAFETY

10 | Westinghouse Outdoor Power Equipment
1. Washer (2 used)
2. Flange Bolt M8 x16mm (4 used)
3. Hairpin Cotter Pin (2 used)
4. Wheel Axle Pin (2)
CAUTION
Always have assistance when lifting
the generator. The generator is heavy;
lifting it could cause bodily harm.
Avoid cutting on or near staples
to prevent personal injury.
Tools required – box cutter or similar device.
1. Carefully cut the packing tape on top of the carton.
2. Remove the Wheel Kit Accessories cardboard box.
3. Locate the propane hose. (If you are having trouble
locating the hose look between top of muer and
bottom of fuel tank.)
4. Carefully cut two sides of the carton to
remove the generator.
WHAT COMES IN THE BOX
Manual
Quick Start Guide/Maintenance Schedule
Wireless Remote Starter (1)
1.1 Liter Bottle of SAE 10W30 Oil (1)
Spark Plug Socket Wrench (1)
11W Battery Charger, (14V .8A output) (1)
Wheel Kit Accessories Box
Funnel (1)
Propane hose (1)
WHEEL KIT ACCESSORIES BOX
Open the Wheel Kit Accessories box and
verify the contents against the list right. If any
parts are missing, please locate an authorized
Westinghouse Generator dealer at service@
wpowereq.com or call 1-855-944-3571.
UNPACKING
Wheel and Feet Kit Hardware
1
2
3
4

Westinghouse Outdoor Power Equipment | 11
INSTALLING WHEELS AND FEET
BEFORE ASSEMBLING THE
GENERATOR, REVIEW THE SAFETY
SECTION STARTING ON PAGE 5.
CAUTION
Never lift the generator without
assistance. The generator is heavy
and lifting without assistance could
result in personal injury.
Never use the handles as a lifting point
to support the entire weight of the
generator. Only use the handles to move
the generator by lifting the handles and
using the wheels to move the generator.
Use caution when collapsing the
handles. Hands and ngers could get
caught and pinched.
NOTICE
Assembling the generator will require lifting the unit
on one side. Make sure all engine oil and fuel are
drained from the unit prior to assembling. Once
assembled, the wheel kit is not intended for on-
road use. The wheel kit is designed for use on this
generator only.
INSTALLING FEET TO FRAME
1. Place generator on a at surface.
2. Place a piece of cardboard or other soft material to
tip the generator onto, to protect the frame paint and
prevent the generator from sliding. Tip the generator
onto the side.
3. Install the mounting feet to the frame using the M8
ange bolts included.
1 - Mounting Foot
2 - Flange Bolts M8
1
2
Figure 1 - Assemble Mounting Feet to Frame
INSTALLING WHEELS TO FRAME
1. Insert axle pin through washer and wheel.
2. Install the wheel with axle pin through the axle
bracket on the frame. The eye of the bolt should be
facing toward the inside of the generator.
21
3
Figure 3 - Assemble Wheel to Frame
3. Install the hairpin cotter through the axle pin to lock it
in place.
1 - Axle Bracket
2 - Hairpin Clip
3 - Axle Pin
4. Repeat previous steps on other wheel.
ASSEMBLY
Figure 2 -Wheel Assembly

12 | Westinghouse Outdoor Power Equipment
CONNECTING THE BATTERY
WARNING
To avoid electrics hock:
• ALWAYS connect the positive (+)
battery cable (red boot) rst when
connecting battery cables.
• ALWAYS disconnect the negative (-)
battery cable (black boot) rst when
disconnecting battery cables.
• NEVER connect the negative (-)
battery cable (black boot) to the
positive (+) post on the battery.
• NEVER connect the positive (+)
battery cable (red boot) to the
negative (-) post on the battery.
• NEVER touch both battery posts
simultaneously.
• NEVER place a metal tool across
both battery posts.
• ALWAYS use insulated or
nonconducting tools when installing
the battery.
1. Using a screw driver, remove the screw on the red
positive (+) battery lead.
2. Securely tighten the positive (+) battery cable (red
boot) to the positive (+) battery post. Make sure boot
is over battery post.
ASSEMBLY
3. Locate the black negative (-) cable attached to the
alternator case, route it to the negative (-) battery
post. See Figure 5 below for location (1) of negative (-)
cable.
1
Figure 5 - Locating Negative (-) Cable
4. Remove the screw on the negative (-) battery post. Pull
back the black boot and securely attach the negative
(-) battery cable (black boot) to the negative (-) battery
post and tighten screw. Replace the black boot so it
protects the cable lug and battery post.
NOTICE
The electric start generator is equipped with a battery
charging feature. Once the engine is running, a small
charge is supplied to the battery via the battery cables
and will slowly recharge the battery.

Westinghouse Outdoor Power Equipment | 13
Push Button Electric Start: Starts and stops
the engine.
Engine Control Switch/Battery Disconnect:
Allows fuel to ow to engine and energizes
the ignition system. Also, disconnects battery
power when in “Stop” position.
Fuel Cap: Close until clicking sound is heard.
Control Panel: Contains the circuit breakers
and outlets.
Battery: Included for electric start models.
Oil Fill Plug/Dipstick: Must be removed to add
and check oil.
Oil Drain Plug: Must be removed to drain
engine oil
FEATURES
Never Flat Wheels: For easy portability
Fuel Shut o Valve: Controls the ow of gasoline
to the engine.
Auto Choke: You can manually adjust the choke if
the battery is not connected.
Single Piece Handle: Includes rubber grip. Allows
you to easily push or pull unit with one hand.
Recoil Start: Used to manually start the generator.
Propane Hook Up: Hook up your propane tank with
the LPG hose provided to this inlet.
Fuel Selector Switch: Used to select and turn on
gasoline or propane fuel source.
2
1
1
5
6
7
8
10
9
11
12
13
14
2
3
4
3
4
5
7
6
11
13
14
9
12
10
8

14 | Westinghouse Outdoor Power Equipment
Fuel Gauge: Indicates fuel level.
Spark Plug Boot (Wire): Must be removed when servicing the engine or the
spark plug.
CARB Canister: Required for models sold into and used in California.
Muer and Spark Arrester: Avoid contact until engine is cooled down.
Spark arrestor prevents sparks from exiting the muer. It must be removed
for servicing.
Alternator Cover: Gain access to alternator wiring.
Remote Start Pairing Button: Initiates the remote key fob pairing function.
FEATURES
15
16
17
18
19
20
15
16
17
18
19
20

Westinghouse Outdoor Power Equipment | 15
VFT Data Center: Press and release the mode
button to toggle between Voltage, Frequency,
Total Hour Meter and Run/Maintenance Timer.
Frequency in hertz
Lifetime run hours
Run/Maintenance
Voltage
The Run/Maintenance Timer displays the time in hours
and minutes each time the generator is ran. The run
timer resets to 00:00 when the generator is shut o.
Built into this run timer is a maintenance reminder.
When the new generator is ran for 25 hours, the meter
will display P25. This is to remind you to change the oil
after the initial 25 hours of run time. When it displays
P50, it is time to clean the air lter. When it displays
P100 it is time change/clean the fuel lter, clean the air
lter, and change the oil.
20-Amp Circuit Breakers: Each circuit breaker limits
the current that can be delivered through the 120-volt
duplex outlets to 20amps.
30-Amp Circuit Breakers: Each circuit breaker limits
the current that can be delivered through each 120-volt
leg of the L14-30R 30A outlet.
Ground Terminal: The ground terminal is used to
ground the generator.
Fuel Selector Switch: Select and turn on gas or
propane.
Push Button Electric Start:
• Push for 1 second to automatically start the engine.
• Push again to stop the engine.
Engine Control Switch/Battery Disconnect: Switch
to “Stop” to stop the engine. When in “Stop” position it
prevents the unit from drawing power from the battery.
Switch to “Run” before starting engine.
Main Circuit Breaker: The main circuit breaker controls
total output of all outlets to protect the generator.
120-Volt, 20-Amp Duplex GFCI Outlets
(NEMA 5-20R): Each outlet is capable of carrying
a maximum of 20 amps on a single receptacle or a
combination of both receptacles.
120/240-Volt, 30-Amp Twist Lock Outlet
(NEMA L14-30R): Outlet can supply either
120V or 240V output up to 30A.
120/240-Volt, 50-Amp Outlet (NEMA 14-50R):
Outlet can supply either 120V or 240V up
to 50 amps.
Smart Switch Outlet: Connects the Westinghouse ST
Switch (sold separately) to the control panel.
Battery Charge Port: Charge generators battery with
included charger.
Battery Indicator Light: When light is illuminated,
the battery is connected and providing power to the
electronics.
CONTROL PANEL FEATURES
1
8
9
10
11
12
13
14
2
3
4
5
6
7
3456 7219
10 12118
FEATURES
13 14

16 | Westinghouse Outdoor Power Equipment
No Connected Loads – Make sure the generator has no
connected loads before starting it. To ensure there are no
connected loads, unplug any electrical extension cords that
are plugged into the control panel receptacles.
NOTICE
Starting the generator with loads already applied to it could result in
damage to any appliance being powered o the generator during the
brief start-up period.
Grounding the Generator – The National Electric Code
(NEC), as well as many local electrical codes, may require
the generator to be connected to earth ground. The most
common application that requires a ground rod is when you
are using the generator as a separately derived system to
provide back up power to your house. Typically this is when a
transfer switch has a switched neutral.
As the generator application has many variables that cannot
be determined by the manufacturer of the generator, a
licensed electrician will need to determine if a grounding rod is
needed.
If a licensed electrician has determine the application requires
a ground rod, make sure it is connected to earth ground by
connecting the ground terminal on the control panel to earth
ground using copper wire (minimum 10 AWG). Consult a
qualied electrician for local grounding requirements.
Neutral Bonded: There is a permanent conduct or between
the generator (stator winding) and the frame.
WARNING
Be sure the generator is properly connected to
earth ground before operating. The generator
must be grounded to prevent electrical shock
due to faulty appliances.
High Altitude Operation
Engine power is reduced the higher you operate above sea
level. Output will be reduced approximately 3.5% for every
1000ft of increased altitude from sea level. This is a natural
occurrence and cannot be adjusted by engine. Increased
exhaust emissions can also result due to increased fuel
mixture. Other issues include hard starting, increased fuel
consumption and spark plug fouling. Contact our service
team 1-855-944-3571 for altitude part kits.
BEFORE STARTING THE GENERATOR
BEFORE STARTING THE GENERATOR,
REVIEW SAFETY SECTION STARTING ON
PAGE 5.
Location Selection – Before starting the generator, avoid
exhaust and location hazards by verifying:
• You have selected a location to operate the generator
that is outdoors and well ventilated.
• You have selected a location with a level and solid
surface on which to place the generator.
• You have selected a location that is at least 15 feet
(4.5 m) away from any building, other equipment or
combustible material.
• If the generator is located close to a building, make
sure it is not located near any windows, doors and/or
vents.
WARNING
Always operate the generator on a level surface.
Placing the generator on non level surfaces can
cause the generator to tip over, causing fuel and
oil to spill. Spilled fuel can ignite if it comes in
contact with an ignition source such as a very hot
surface.
NOTICE
Only operate the generator on a solid, level surface. Operating the
generator on a surface with loose material such as sand or grass
clippings can cause debris to be ingested by the generator that
could:
• Block cooling vents
• Block air intake system
Weather – Never operate your generator outdoors during
rain, snow or any combination of weather conditions that
could lead to moisture collecting on, in or around the
generator.
Dry Surface – Always operate the generator on a dry
surface free of any moisture.
OPERATION

Westinghouse Outdoor Power Equipment | 17
POWER CORD
Using Extension Cords
Westinghouse assumes no responsibility for the content within this table. The use of this table is the responsibility of
the user only. This table is intended for reference only. The results produced by using this table are not guaranteed to
be correct or applicable in all situations as the type and construction of cords are highly variable. Always check with
local regulations and a licensed electrician prior to installing or connecting an electrical appliance
Using Westinghouse Power Cord
Use the extension cord chart to determine the size
of the conductor for extension cord applications.
Determine the distance of the generator to the
appliance on the top line of the chart. Then select the
rated amperage of the generator on the left side of the
chart. Where the two meet is the size of the conductor
required for the application.
When using the WCG25/WCG20 power cord (sold
separate) connect to the 120/240V outlet. The opposite
end of the power cord is a fan tail receptacle with
2 green receptacles and 2 red receptacles. Each
receptacle is rated at 120 volts AC. To balance the
load on the generator’s alternator, use the red and
green identiers on the fan tail receptacle. To keep
the load balanced, connect the loads so that both
color receptacles are used. An example is one in red
and one in green. Do not connect 2 in red and none in
green, or 2 in green and none in red. If only one color
receptacle is used with multiple loads, the alternator
may experience an unbalanced load, causing undue
vibration to generator.
OPERATION
1
2
- WCG25/WCG20 Extension Cord
Red Dots
Green Dots

18 | Westinghouse Outdoor Power Equipment
ADDING / CHECKING ENGINE
FLUIDS AND FUEL
BEFORE ADDING/CHECKING ENGINE
FLUIDS AND FUEL, REVIEW SAFETY
SECTION STARTING ON PAGE 5.
DANGER
Filling the fuel tank with gasoline while
the generator is running can cause
gasoline to leak and come in contact
with hot surfaces that can ignite the
gasoline.
Before starting the generator, always check the level of:
• Engine oil
• Gasoline in the fuel tank
Once the generator is started and the engine gets warm,
it is not safe to add gasoline to the fuel tank or engine oil
to the engine while the engine is running or the engine
and muer are hot.
CHECKING AND / OR ADDING ENGINE OIL
WARNING
Internal pressure can build in the
engine crankcase while the engine
is running. Removing the oil ll plug/
dipstick while the engine is hot can
cause extremely hot oil to spray out
of the crankcase and can severely
burn skin. Allow engine oil to cool for
several minutes before removing the
oil ll plug/dipstick.
The unit as shipped does not contain oil in the engine.
You must add engine oil before starting the generator
for the rst time. See Checking Engine Oil and Adding
Engine Oil for instructions on checking engine oil level
and the procedure for adding engine oil.
NOTICE
The engine does not contain engine oil as shipped.
Attempting to start the engine can damage
engine components. The owner of the generator
is responsible to ensure the proper oil level is
maintained during the operation of the generator.
Failure to maintain the proper oil level can result in
engine damage.
OPERATION
CONNECTING THE GENERATOR TO A
BUILDING ELECTRICAL SYSTEM
It is recommended to use a manual transfer switch
when connecting directly to a buildings electrical
system. Connecting a portable generator to a buildings
electrical system must be made in strict compliance
with all national and local electrical codes and laws,
and be completed by a qualied electrician.
TRANSFER SWITCH CONNECTIONS
The Westinghouse generator is wired with the neutral
bonded to ground. If you are connecting your generator
to a panel board transfer switch, a licensed electrician
will need to consider removing the bonded neutral to
ensure proper operation of household GFCI circuits.
Begin by removing the alternator cover. Once the
cover is o remove the nut that holds the bonded
ground jumper wire (see “2” in Figure 6). Once the nut
is removed take the bonded jumper wire o and re-secure
the nut. Next remove the screw holding the neutral ground
wire (see “1” in Figure 6). Attach the bonded jumper wire
(2) to the neutral ground (1) and tighten the screw.
If the bonded neutral is removed the generator must be
relabeled as oating neutral on the control panel.
If your generator is equipped with GFCI receptacles,
removing the bonded neutral may not allow proper
operation of the GFCI receptacles. Always keep the
jumper wire in case it is needed for future use when not
connected to a transfer switch.
1
11
22
2
Figure 6
REMOVE
MOVE WIRE HERE
Alternator Neutral Ground Wire (white/Green)
Alternator Bonded Jumper Wire (white/Green)

Westinghouse Outdoor Power Equipment | 19
ADDING GASOLINE TO THE FUEL TANK
WARNING
Never refuel the generator while the
engine is running.
Always turn the engine o and allow
the generator to cool before refueling.
Required Gasoline – Only use gasoline that meets the
following requirements:
• Unleaded gasoline only
• Gasoline with maximum 10% ethanol added
• Gasoline with an 87 octane rating or higher
Filling the Fuel Tank – Follow the steps below to ll the
fuel tank:
1. Shut o the generator.
2. Allow the generator to cool down so all surface areas
of the muer and engine are cool to the touch.
3. Move the generator to a at surface.
4. Clean area around the fuel cap.
5. Remove the fuel cap by rotating counterclockwise.
6. Slowly add gasoline into the fuel tank. Be very careful
not to overll the tank. The gasoline level should NOT
be higher than the ller neck (see Figure 7).
7. Install the fuel cap by rotating clockwise until
you hear a click, indicating the cap is completely
installed.
Figure 7 - Maximum Gasoline Fill Level
CAUTION
Avoid prolonged skin contact with
gasoline. Avoid prolonged breathing of
gasoline vapors.
OPERATION
CONNECTING TO STANDARD LPG/PROPANE TANK
BEFORE CONNECTING PROPANE TANK TO
THE GENERATOR PLEASE REVIEW FUEL
SAFETY SECTION
Connecting LPG Tank
1. Make sure the generator is o, on a at surface in well
ventilated area.
2. Make sure propane tank valve is in the o position.
3. Make sure the fuel selector switch on the generator
control panel is pointing downward to “Propane”.
4. Remove the plastic cover on the generator propane
inlet valve.
5. Tighten the LPG hose (included) to the generator
propane inlet. DO NOT OVER-TIGHTEN 35-88 Ib-in
maximum.
6. Attach the other end of the hose to a tank of LPG/
Propane and hand tighten.
7. Check all connections for leaks by wetting the ttings
with soapy water. Anywhere that bubbles appear or
grow indicates a leak in the connection. If a leak exists
at a tting then turn o the tank valve and tighten the
tting. Turn the gas back on and recheck with soapy
water again. If the leak continues or if the leak is not
at a tting then do not use the generator and contact
customer service.
NOTICE
• When using standard 20 or 30 pound capacity LPG tanks, make sure
they have Type 1, right hand Acme threads.
• Verify the requalication date on the tank has not expired.
• All new tanks must be purged of air and moisture prior to lling. Used
tanks that have not been plugged or kept closed must also be purged
• The purging process should be done by a LPG supplier. (Tanks from
an exchange supplier should have been purged and lled properly
already)
• Always position the tank so the connection between the valve and the
gas inlet won’t cause sharp bends or kinks in the hose.
WARNING
Do not start generator if you smell propane. This may
result in explosion hazard. Do not use provided LPG
hose for any other appliances. Always turn o the
propane tank and disconnect LPG hose when not in
use.

20 | Westinghouse Outdoor Power Equipment
OPERATION
DANGER
Never use the generator in a location that is wet or
damp. Never expose the generator to rain, snow,
water spray or standing water while in use. Protect
the generator from all hazardous weather conditions.
Moisture or ice can cause a short circuit or other
malfunction in the electrical circuit.
Never operate the generator in an enclosed area.
Engine exhaust contains carbon monoxide. Only
operate the generator outside and away from
windows, doors and vents.
NOTICE
The engine is equipped with a low oil shutdown switch. If the oil
level becomes low, the engine may shut down and not start until
the oil is lled to the proper level. Poor oil quality may interfere with
the operation of the low oil shutdown switch.
The owner of the generator is responsible to ensure the proper oil
level is maintained during the operation of the generator. Failure to
maintain the proper oil level can result in engine damage.
NOTICE
When operating on LPG it is common for frost to form on the tank
and regulators. This is not an indication of a problem. The amount
of frost that forms can be aected by the size of the container,
the amount of fuel being used, the humidity of the air and other
operating conditions. In standard use this frost may reduce ow
of gas and lower performance. If frost becomes an issue try
exchanging fuel tanks to allow the rst tank to warm up. You can
also temporarily warm the tank up by pouring warm water over the
top of the propane tank.
SWITCHING FUEL SOURCES
BEFORE ADDING GAS TO THE TANK
PLEASE REVIEW FUEL SAFETY
SECTION
The below assumes that the propane fuel line is already
attached to the generator securely and safely.
While the unit is running simply turn the FUEL
SELECTOR knob to the desired fuel source. If you
want to switch from gasoline to propane make sure the
propane tank valve is open before you switch. When
you move from propane to gasoline shut the propane
valve after you have switched to gas.
NOTICE
If you do not plan on operating the unit on propane do not leave
the propane tank valve open.
When starting on propane the engine may run rough for a few
seconds while it purges gasoline in the carburetor.
If the engine fails when switching fuel sources simply restart the
unit on the fuel source that you switched to.
CONNECTING TO LARGE LPG/PROPANE TANK
BEFORE CONNECTING PROPANE TANK TO
THE GENERATOR PLEASE REVIEW FUEL
SAFETY SECTION
You can hook up your Duel Fuel Generator to a large home
LP tank. It is required that you consult a licensed plumber to
properly connect your generator to the tank.
To properly connect with a large propane tank, you must
rst check and conrm the LP fuel pressure at the outlet of
the LP tank. The LP fuel pressure should be 14-10” of water
column, which is the standard fuel pressure for residential
gas red appliances.
If the LP fuel pressure is within the 14-10” water column
range, the primary fuel regulator should be removed from
the fuel line components. Then plumb directly from the LP
tank to the secondary regulator assembled to the generator.
WARNING
You must consult a certied plumber to connect
to large LP tank safely.
BEFORE STARTING THE GENERATOR
BEFORE STARTING THE GENERATOR,
REVIEW SAFETY SECTION STARTING ON
PAGE 5.
Before attempting to start the generator,
verify the following:
• The engine is lled with engine oil. See Checking Engine
Oil.
• The generator is situated in a proper location (Location
Selection).
• The generator is on a dry surface (Weather and Dry
Surface).
• All loads are disconnected from the generator (No
Connected Loads).
• The generator is properly grounded.
• Propane connection is secure with no leaks or damage.
See Connecting LPG Tank.