Westinghouse WTB4604S User manual

USER MANUAL
REFRIGERATION
Top Mount, Bottom Mount, French Door & Single Door
REGISTER YOUR
APPLIANCE TODAY
to get product tips, safety
notifications and more.
westinghouse.com.au/register

2CONTENTS
Important safety instructions........................................................3
Refrigerator Features
Top mount refrigerator features ......................................... 4
Bottom mount refrigerator features .................................5
French door features ................................................................ 6
Bottom mount with ice & water
refrigerator features ...............................................................7
French door with ice & water features............................. 8
Single door refrigerator features ....................................... 9
Single door freezer features.................................................10
Installing your new refrigerator
Unpacking your refrigerator.................................................. 11
Locating your refrigerator. ..................................................... 11
Installing your refrigerator...................................................... 11
Fitting the handles .................................................................... 12
Ice and Water Installation
Water filter .................................................................................... 12
Water supply & plumbing...................................................... 12
Replacing the water filter..............................................................14
Using your refrigerator
Removing Features...................................................................15
Crisper Bin.....................................................................................15
SpillSafe™ glass shelves ..........................................................15
Freezer Shelves...........................................................................15
Drawers with telescopic slides............................................ 15
Twist & Serve ice ........................................................................16
LED Lighting ................................................................................ 17
Temperature control................................................................. 17
About the User Interface
Top mount & single door models.......................................18
Bottom mount/French Door models..............................20
All freezer models...................................................................... 21
Bottom mount/French Door Ice & Water.....................22
General information
Error Codes..................................................................................23
Cleaning the refrigerator.......................................................24
Food storage guide .................................................................25
Troubleshooting.........................................................................26
Ice & water troubleshooting................................................28
Warranty ........................................................................................31
CONTENTS
CONGRATULATIONS
Dear customer,
Congratulations and thank you for choosing our
refrigerator. We are sure you will find your new
refrigerator a pleasure to use. Before you use the
refrigerator we recommend that you read through
the relevant sections of this manual, which provides
a description of your refrigerator and its functions.
To avoid the risks that are always present when you use
an electric appliance, it is important that the refrigerator
is installed correctly and that you read the safety
instructions carefully to avoid misuse and hazards.
We recommend that you keep this instruction booklet
for future reference and pass it on to any future owners.
After unpacking the refrigerator, please check it is not
damaged. If in doubt, do not use the refrigerator but
contact your local customer care centre.
The symbols you will see in this booklet have these
meanings:
WARNING
WARNING
This symbol indicates information concerning your
personal safety.
WARNING
CAUTION
This symbol indicates information on how to avoid
damaging the refrigerator
TIPS & INFORMATION
IMPORTANT
This symbol indicates tips and information about use
of the refrigerator
ENVIRONMENTAL TIPS
ENVIRONMENT
This symbol indicates tips and information about
economical and ecological use of the refrigerator
Conditions of use
This refrigerator is designed and intended to be used in
normal domestic applications only.
Record model and serial number here:
Model number:........................................................................................
Serial number:.........................................................................................

3SAFETY
Note: You must read these warnings carefully before
installing or using the refrigerator. If you need assistance,
contact your customer care centre. The manufacturer will
not accept liability, should these instructions or any other
safety instructions incorporated in this book be ignored.
WARNING
WARNING
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety. Children should
be supervised to ensure that they do not play with
the appliance.
• It is essential the power point is properly earthed to
ground. Consult a qualified electrician if you
are unsure.
• Do not use electrical appliances inside the food
storage compartments of the appliance, unless they
are of the type recommended by the manufacturer.
• Unplug the refrigerator before cleaning or moving it
to avoid electric shock.
• Never unplug the refrigerator by pulling the electrical
cord as this may damage it. Grip the plug firmly and
pull straight out.
• If the power cord is damaged, it must be replaced
by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
• Don’t use a steam cleaner. If live components come
into contact with condensing steam, they may short-
circuit or cause an electric shock.
• Do not store explosive substances such as aerosol
cans with a flammable propellant in this appliance.
If pressurised aerosol containers bear the word
‘flammable’ and/or a small flame symbol, do not store
them inside any refrigerator or freezer. If you do so
you may cause an explosion.
• Do not damage the refrigerant circuit.
• This appliance contains insulation formed with
flammable blowing gases. Avoid safety hazards by
carefully disposing of this appliance.
• If you wish to discard this refrigerator, please contact
your local authorities and ask for the correct method
of disposal.
• When you dispose of your old refrigerators and
freezers, remove any doors. Children can suffocate if
they get trapped inside.
• The plug must be accessible when the appliance is
in position.
• Never try to repair the refrigerator yourself, only use a
qualified or authorized service person for repairs.
IMPORTANT SAFETY
INSTRUCTIONS
WARNING
WARNING
R600a refrigerant warning
This appliance contains flammable R600a refrigerant.
Avoid safety hazards by carefully installing, handling,
servicing and disposing of this appliance.
• Ensure that the tubing of the refrigerant circuit is not
damaged during transportation and installation.
• Leaking refrigerant may cause eye injuries or ignite.
• The room for installing appliance must be at least
1m3 per 8g of refrigerant. The amount of refrigerant in
the appliance can be found on the rating plate inside
the appliance.
• If you are unsure of the refrigerant check the rating
plate inside the refrigerator compartment.
• It is hazardous for anyone other than an Authorised
Service Person to service this appliance. In
Queensland Australia the Authorisation Service
Person MUST hold a Gas Work Authorisation for
hydrocarbon refrigerants to carry out servicing or
repairs which involve the removal of covers.
• Keep ventilation openings in the appliance enclosure
or in the built-in structure, clear of obstruction.
• Do not use mechanical devices or other means to
accelerate the defrosting process, other than those
recommended by the manufacturer.

4FEATURES
Features may vary depending on model. Not all models will have features listed.
TOP MOUNT REFRIGERATOR FEATURES
Deli drawer
Use the deli drawer to store
foods like small goods, fresh or
cooked meat and cheese, or as
an additional crisper. The drawer
will prevent strong food odours
from impacting the rest of the
refrigerator. To remove the deli
drawer, pull it forward, then lift it
up and pull it further forward.
FlexFresh crisper
Use the crisper to store
vegetables, fruit or small goods.
Change the humidity by sliding
the humidity control.
FamilySafe lockable
compartment
This compartment can be
used to store dairy and is
also lockable for storing
items like cosmetics and
medicines. To operate the
lock, turn the knob located
on the front of the bin.
Bottle storage bin
with fingers
Use the bottle bin for tall
bottle storage. The bottle
bin can be removed by
lifting it up over the support
lugs. To replace, push down
over the support lugs to
lock in place.
Adjustable freezer
bin divider
Use the dividers to
organise stored items by
twisting to lock into the
holes provided.
Twist & Serve Ice
Refer to the section “Using
your Refrigerator” for details
on removing, relocating and
using this feature.
Freezer temperature
control
Refer to the section
“Temperature control” for
details on using this feature.
LED lighting
Your refrigerator is fitted with
LED lighting.
Refrigerator control panel
From this panel you can control
the temperature of the refrigerator
compartment as well as setting
the quick chill function or resetting
the door alarm.
For further information on how to
use this feature refer to the section
“About the User Interface”.
Freezer control
This is a simple slide control to adjust the temperature
of your freezer compartment.
For further information on how to use this feature refer
to the section “Using your Refrigerator”.
WTB4604S illustrated
Crisper divider
Use the crisper divider to
organise and separate fruit
and vegetables.
SpillSafeTM glass shelves
The glass shelves improve
visibility and isolate leaks-
preventing spills from dripping
down to the shelves below.
FlexStor door bins
Slide FlexStor bins to
meet different storage
needs. To remove, lift and
tilt. To replace, tilt the
top and push down until
locked in place.
Door storage bin
The door bin can be
removed by lifting it up
over the support lugs.
To replace, push down
over the support lugs to
lock in place.
Humidity control
Change the humidity by sliding
the humidity control. Less humid
conditions are recommended for
fruit, while more humid conditions
are recommended for vegetables.

5FEATURES
WBE5304S illustrated
BOTTOM MOUNT REFRIGERATOR
FEATURES
FlexFresh crisper
Use the crisper to store
vegetables, fruit or small goods.
Change the humidity by sliding
the humidity control.
Twist & Serve Ice
Refer to the section “Using
your Refrigerator” for
details on removing and
using this feature.
LED lighting
Your refrigerator is fitted with
LED lighting.
Bottle rack
(Available in selected
models only)
Refrigerator/freezer
control panel
From this panel you can control
the temperature of the refrigerator
and freezer compartments as well
as setting the quick freeze function
or resetting the door alarm.
For further information on how to
use this feature refer to the section
“About the User Interface”.
Features may vary depending on model. Not all models will have features listed.
Freezer storage bin
Refer to the section “Using
your Refrigerator” for details
on removing, and using
this feature.
SpillSafeTM glass shelves
The glass shelves improve
visibility and isolate leaks-
preventing spills from dripping
down to the shelves below.
Crisper divider
Use the crisper divider to organise
and separate fruit and vegetables.
FamilySafe lockable
compartment
This compartment can be
used to store dairy and is
also lockable for storing
items like cosmetics and
medicines. To operate the
lock, turn the knob located
on the front of the bin.
FlexStor bins
Slide FlexStor bins to
meet different storage
needs. To remove, lift and
tilt. To replace, tilt the
top and push down until
locked in place.
Door storage bin
The door bin can be
removed by lifting it up
over the support lugs.
To replace, push down
over the support lugs to
lock in place.
Bottle storage bin
with fingers
Use the bottle bin for tall
bottle storage. The bottle
bin can be removed by
lifting it up over the support
lugs. To replace, push down
over the support lugs to
lock in place.
Humidity control
Change the humidity by sliding
the humidity control. Less humid
conditions are recommended for
fruit, while more humid conditions
are recommended for vegetables.

6FEATURES
WHE5200S illustrated
FRENCH DOOR REFRIGERATOR FEATURES
FlexFresh crisper
Use the crisper to store
vegetables, fruit or small goods.
Change the humidity by sliding
the humidity control.
Twist & Serve Ice
Refer to the section “Using
your Refrigerator” for details
on removing and using
this feature.
LED lighting
Your refrigerator is fitted with
LED lighting.
Bottle rack
(Available in selected
models only)
Refrigerator/freezer
control panel
From this panel you can control the
temperature of the refrigerator and
freezer compartments as well as
setting the quick freeze function or
resetting the door alarm.
For further information on how to
use this feature refer to the section
“About the User Interface”.
Features may vary depending on model. Not all models will have features listed.
Freezer storage bin
Refer to the section “Using
your Refrigerator” for details on
removing, and using this feature.
Crisper divider
Use the crisper divider to organise
and separate fruit and vegetables.
FamilySafe lockable
compartment
This compartment can be
used to store dairy and is
also lockable for storing
items like cosmetics and
medicines. To operate the
lock, turn the knob located
on the front of the bin.
FlexStor door bins
Slide FlexStor bins to
meet different storage
needs. To remove, lift and
tilt. To replace, tilt the
top and push down until
locked in place.
Door storage bin
The door bin can be
removed by lifting it up
over the support lugs. To
replace, push down over
the support lugs to lock
in place.
Bottle storage bin
with fingers
Use the bottle bin for tall
bottle storage. The bottle
bin can be removed by
lifting it up over the support
lugs. To replace, push down
over the support lugs to lock
in place.
SpillSafeTM glass shelves
The glass shelves improve
visibility and isolate leaks-
preventing spills from dripping
down to the shelves below.
Humidity control
Change the humidity by sliding
the humidity control. Less humid
conditions are recommended for
fruit, while more humid conditions
are recommended for vegetables.

7FEATURES
WBE5360S illustrated
BOTTOM MOUNT ICE & WATER
REFRIGERATOR FEATURES
Automatic Ice maker
Refer to the section “Using your
Refrigerator” for details on using
this feature.
LED lighting
Your refrigerator is fitted with
LED lighting.
Bottle rack
(Available in selected
models only)
Refrigerator/freezer
control panel
From this panel you can
control the temperature of
the refrigerator and freezer
compartments as well as setting
the quick freeze function,
controlling the Ice Maker or
resetting the door alarm.
For further information on how
to use this feature refer to the
section “About the
User Interface”.
Features may vary depending on model. Not all models will have features listed.
Water filter
Freezer storage bin
Refer to the section “Using
your Refrigerator” for details
on using this feature.
FamilySafe lockable
compartment
This compartment can be
used to store dairy and is
also lockable for storing
items like cosmetics and
medicines. To operate the
lock, turn the knob located
on the front of the bin.
FlexStor door bins
Slide FlexStor bins to meet
different storage needs.
To remove, lift and tilt. To
replace, tilt the top and push
down until locked in place.
Door storage bin
The door bin can be
removed by lifting it up
over the support lugs.
To replace, push down
over the support lugs to
lock in place.
Bottle storage
bin with fingers
Use the bottle bin for tall
bottle storage. The bottle
bin can be removed by
lifting it up over the support
lugs. To replace, push down
over the support lugs to
lock in place.
FlexFresh crisper
Use the crisper to store
vegetables, fruit or small goods.
Change the humidity by sliding the
humidity control.
Crisper divider
Use the crisper divider to organise
and separate fruit and vegetables.
SpillSafeTM glass shelves
The glass shelves improve
visibility and isolate leaks-
preventing spills from dripping
down to the shelves below.
Humidity control
Change the humidity by sliding
the humidity control. Less humid
conditions are recommended for
fruit, while more humid conditions
are recommended for vegetables.

8FEATURES
WHE5260S illustrated
FRENCH DOOR ICE & WATER REFRIGERATOR FEATURES
Automatic ice maker
Refer to the section “Using
your Refrigerator” for details
on using this feature.
LED lighting
Your refrigerator is fitted with
LED lighting.
Refrigerator/freezer
control panel
From this panel you can
control the temperature of
the refrigerator and freezer
compartments as well as setting
the quick freeze function,
controlling the Ice Maker or
resetting the door alarm.
For further information on
how to use this feature refer
to the section “About the User
Interface”.
Features may vary depending on model. Not all models will have features listed.
Water filter
Freezer storage bin
Refer to the section “Using
your Refrigerator” for details
on using this feature.
FamilySafe lockable
compartment
This compartment can be
used to store dairy and is
also lockable for storing
items like cosmetics and
medicines. To operate the
lock, turn the knob located
on the front of the bin.
FlexStor bins
Slide FlexStor bins to
meet different storage
needs. To remove, lift and
tilt. To replace, tilt the
top and push down until
locked in place.
Door storage bin
The door bin can be
removed by lifting it up
over the support lugs. To
replace, push down over
the support lugs to lock
in place.
Bottle storage bin
with fingers
Use the bottle bin for tall
bottle storage. The bottle
bin can be removed by
lifting it up over the support
lugs. To replace, push down
over the support lugs to
lock in place.
FlexFresh crisper
Use the crisper to store
vegetables, fruit or small goods.
Change the humidity by sliding
the humidity control.
Crisper divider
Use the crisper divider to
organise and separate fruit
and vegetables.
Bottle Rack
(Available in selected
models only)
SpillSafeTM glass
shelves
The glass shelves improve
visibility and isolate leaks-
preventing spills from
dripping down to the
shelves below.
Humidity control
Change the humidity by sliding
the humidity control. Less humid
conditions are recommended for
fruit, while more humid conditions
are recommended for vegetables.

9FEATURES
Features may vary depending on model. Not all models will have features listed.
SINGLE DOOR REFRIGERATOR FEATURES
Deli drawer
Use the deli drawer to store
foods like small goods, fresh
or cooked meat and cheese,
or as an additional crisper.
The drawer will prevent strong
food odours from penetrating
the rest of the refrigerator. To
remove the deli drawer, pull it
forward, then lift it up and pull
it further forward.
FlexFresh crisper
Use the crisper to store
vegetables, fruit or small goods.
LED Lighting
Your refrigerator is fitted with
LED lighting.
Refrigerator control panel
From this panel you can control
the temperature of the refrigerator
compartment as well as setting the
quick chill function or resetting the
door alarm.
For further information on how to
use this feature refer to the section
“About the User Interface”.
WRB5004S
illustrated
FamilySafe lockable
compartment
This compartment can be
used to store dairy and is
also lockable for storing
items like cosmetics and
medicines. To operate the
lock, turn the knob located
on the front of the bin.
FlexStor bins
Slide FlexStor bins to
meet different storage
needs. To remove, lift and
tilt. To replace, tilt the
top and push down until
locked in place.
Door storage bin
The door bin can be
removed by lifting it up
over the support lugs. To
replace, push down over
the support lugs to lock
in place.
Bottle storage bin
with fingers
Use the bottle bin for tall
bottle storage. The bottle bin
can be removed by lifting it
up over the support lugs. To
replace, push down over the
support lugs to lock in place.
Crisper divider
Use the crisper divider to
organise and separate fruit
and vegetables.
SpillSafeTM glass shelves
The glass shelves improve
visibility and isolate leaks-
preventing spills from dripping
down to the shelves below.
Humidity control
Change the humidity by sliding
the humidity control. Less humid
conditions are recommended for
fruit, while more humid conditions
are recommended for vegetables.

10 FEATURES
Features may vary depending on model. Not all models will have features listed.
SINGLE DOOR FREEZER FEATURES
Storage bins
Refer to the section “Using
your Refrigerator” for details on
removing, and using this feature.
LED lighting
Your refrigerator is fitted with
LED lighting.
Freezer control
From this panel you can control
the temperature of the freezer as
well as setting the quick freeze
and drinks chill functions or reset
the door alarm.
For further information on
how to use this feature refer to
the section “Controlling your
Refrigerator”.
WFB4204S illustrated
Twist & serve ice
Refer to the section “Using
your Refrigerator” for details
on removing, relocating and
using this feature.

11INSTALLATION
Unpacking
ENVIRONMENTAL TIPS
ENVIRONMENT
Most of the packing materials are recyclable. Please
dispose of those materials through your local recycling
depot or by placing them in appropriate collection
containers.
Important – check for any damages or marks. If you find
the refrigerator is damaged or marked, you must report
it within 7 days should you wish to claim for damage/
marks under the manufacturers warranty. This does not
affect your statutory rights.
Clean your refrigerator thoroughly following the
instructions in the “Cleaning” section and wipe off any
dust that has accumulated during shipping.
Locating the refrigerator
WARNING
CAUTION
Automatic aerosol systems (such as insect control)
should not be located adjacent to the product as the
spray may cause long term damage to the external
plastics of the appliance.
Do not put the refrigerator in a location that is too cold or
is unprotected, for example in a garage or on a veranda.
The ambient temperature should be above 10°C.
Put the refrigerator in a dry place avoiding areas of high
moisture or humidity.
Ensure the refrigerator is located on an even surface.
Adequate ventilation around your refrigerator
The diagram below shows the recommended airspace to
allow for ventilation of your refrigerator.
350mm
50mm
Recommended
airspace
CABINET
DOOR
30mm 30mm
XY
If you have a cupboard above the refrigerator with a rear
gap of less than 100 mm (Y), recommended clearance at
the top of the refrigerator increases from 50mm to 90mm
(X) minimum.
When positioned in a corner area, spacing of at least
350mm (300mm for multi-door models) on the hinge
side will allow the doors to open enough to enable the
removal of bins and shelves.
NOTE: Doors are designed to sit proud of cabinetry (not
flush). The clearances shown above are the recommended
minimum clearances.
The clearance at the rear must not exceed 75mm.
INSTALLING YOUR NEW
APPLIANCE
Installing your refrigerator
1. Roll the refrigerator into place.
The rollers are designed for forward or backward
movement only. They are not castors. Moving the
refrigerator sideways may damage your floor and the
rollers. Before moving your refrigerator ensure height
adjusting nut and the stability foot are fully wound up
off the floor.
2. Wind the large height adjusting nut under door hinge
down until the refrigerator is tilted back by 10mm
(see diagram).
Height adjusting nut
Fixed rear rollers
10 -15mm
3. Wind the large height adjusting nut on the handle
side down until the refrigerator is level and stable.
If you have difficulty winding the nut or height
adjusting foot down, have someone tilt the
refrigerator back so you have better access.
stability foot
wound up
4. Check the alignment of the refrigerator to the
surrounding cupboards to see if it is level. You can
adjust the level as detailed in step 2 and 3.
aligned to
cupboards
ie. even gap top of refrigerator is
level ie. horizontal
adjust front feet for
uneveness of floor
eg. wind this foot
down or up

12 INSTALLATION
INSTALLING YOUR NEW
APPLIANCE
5. If you find your refrigerator rocks from corner to
corner, it means your floor is uneven. Find a piece
of plastic or hardboard etc. and pack it firmly under
the roller.
6. You may now need to fine-tune the installation by
repeating steps 3, 4 and 5.
7. When you have the appliance in its final position, it
needs to be stabilised. Wind the stability foot under
the door hinge down to the floor until it just makes
contact with the floor. Lift the front of the appliance
to take the weight off the stability foot, then turn
it half a turn further to ensure firm contact with
the floor. Wind the large height adjusting nut back
up to ensure all the weight is now on the front
stability foot. Wind the large height adjusting nut
back up to ensure all the weight is now on the front
stability foot.
8. Repeat step 7 for the stability foot on the handle side.
Whenever you need to move the appliance, be sure
to wind the feet back up so that the appliance can
roll freely and be sure to reset it when reinstalling.
stability foot
wound down
front view
9. Plug your refrigerator straight into its own power
point and never use a double adapter. If you need to
roll the refrigerator to get to the plug, remember to
raise the stability foot first.
10. Before you put any food in your refrigerator, it’s
recommended you leave it on for 2 or 3 hours to
check it is running properly.
Fitting the handles
For models with ‘Pole’ handles, the handles are supplied
prepackaged inside your refrigerator and will require
fitting. Refer to the instructions provided in the pack.
Congratulations! You have successfully installed your
new refrigerator.
WARNING
WARNING
Connect to potable water supply only. If using tank or
bore water it is recommended to also use an external
filter (not supplied).
The new hose-sets supplied with the appliances must be
used and old hose-sets should not be reused.
Never connect the appliance to a hot water supply.
Water Filter
It should not be used on water that is micro biologically
unsafe or with water of unknown quality. The service life
of the filter may be reduced in water supplies that contain
an excess of particles or other impurities. Reduced flow
rate is an indication that a new filter is required. Failure to
replace the filter when required can affect the function of
the ice maker. Service calls caused by a failure to replace
the filter are not covered by warranty. Replacement
water filters are available from Electrolux Home Products
Spare Parts Centres and can be posted to you for your
convenience (refer to spare parts contact numbers on the
warranty page).
Contents of installation kit
4 metres of water tubing
DATE FITTED___/___/___
1 x 1/2” tap fitting
Water supply and plumbing
A drinkable water supply to suit a 1/2” tap fitting is
required adjacent to the refrigerator. It is recommended
that a licensed plumber install a new water supply outlet
nearer to the appliance should the tubing supplied not be
long enough. It is not recommended that the tubing be
extended as this could adversely affect the flow of water
to the ice maker or water dispenser. The water dispenser
and automatic ice maker require a drinkable water supply
with a pressure range of between 206kPa and 689kPa
(30PSI and 100PSI). If the water supply is above 100psi a
pressure limiting valve should be installed.
It is recommended that a noise reduction valve also be
fitted in the water supply line. This will reduce water
hammer and its effects from quick action household taps
and fast acting valves on appliances.
The refrigerator water valve is pre-fitted with a push-fit
connector for inserting the water tube. When the tap
connection is other than 1/2”, adapters can be purchased
from plumbing supply stores or good hardware stores.
ICE AND WATER INSTALLATION

13INSTALLATION
Please read before beginning installation.
The water connection to your ice and water product can
be self installed. However, it is recommended that you
seek advice from a licensed plumber before commencing
the installation.
TIPS & INFORMATION
IMPORTANT
Check for water leaks at all water connection points in
the first 2 to 3 hours after installation, and correct it in
case of any water leak. Recheck after 24 hours; if leak
still occurs, it is recommended to contact a licensed
plumber for advice.
Water is to be connected as per diagram below.
(WHE5160SAD shown)
Step 1.
Ensure that the refrigerator
is disconnected from power
supply.
Step 2.
Connect tap fitting to water
supply tap. Tap must be close
to the refrigerator.
Step 3.
Push the tube into tap fitting
past insertion mark.
Step 4.
Connect other end of tube to inlet on rear of refrigerator.
Step 5.
Turn on water and check all joints
and tubes for leaks.
Step 6.
Reconnect the power.
Step 7.
Move the refrigerator back into
place being careful not to kink or
split the tubing.
Step 8.
Switch ON Water Dispenser.
Using a large container, run the
water dispenser to clear air from
lines. This may take a few minutes.
Purge and dispense a minimum
of 2 litres of water. Initial water
may be black in colour. This is
residual carbon dust from the filter
and is non-toxic. If the water is
slow to shut off or the dispenser
is dripping, air may still be in the
lines. Either purge more water
through the system to remove
this air or allow some time for the air to be removed over
subsequent dispensing. For normal use, water dispenser
will automatically shut off after 2 minutes of continuous
operation.
TIPS & INFORMATION
IMPORTANT
As the water cut off is not instant, leave glass under
dispenser briefly until water has stopped flowing to
avoid spills.
Clean and empty the dispenser drip tray regularly to
avoid overflow.
If you have not used the dispenser for some time, discard
the first seven or eight cups of water (contaminants
could have settled in the water pipes).
Step 9
Switch ON Ice Maker.
Once the refrigerator has been running for at least 24
hours remove the ice bin and dispose of the first few
batches of ice to ensure that impurities have been flushed
from the system.
WARNING
CAUTION
Water dispenser should not be used for extended periods
of time. After 2 minutes of continuous use the water
dispenser will automatically shut off.
Party Ice
When the Ice Bin is removed from the cabinet the
Auto Ice Maker will continue to dispense ice into the top
freezer drawer.

14 INSTALLATION
ICE AND WATER INSTALLATION
TIPS & INFORMATION
IMPORTANT
• Always fit the filter as per manufacturer’s instructions.
• If you need to replace water tube, only use approved water quality piping that meets the pressure requirements.
• Make sure your refrigerator is level to avoid uneven ice cubes.
• Replace filter at suggested intervals to avoid water/ice reduction and irregularities in taste.
• Remove and clean ice bin once a month, discarding unused ice cubes. This will ensure fresh, clean ice and smooth
operation of your ice maker.
• Clean and empty the dispenser drip tray regularly to avoid overflow.
WARNING
WARNING
If you have not used the dispenser for some time, discard the first seven or eight cups of water and any ice that the
ice maker produces in the first 24 hours (contaminants could have settled in the water pipes).
Water filter
The water filter is located at the top left side of the fresh food
compartment.
Replacing the water filter
You should change the water filter every six months to ensure the
highest possible water quality.
If your refrigerator has not been used for a period of time (during
a house move for example), change the filter before reinstalling
the refrigerator.
It is not necessary to turn the water supply off to change the filter.
Be ready to wipe up any small amounts of water released during the
filter replacement.
1. Ensure that the ice maker is turned off (Diagram 1).
2. Remove the filter by turning anti-clockwise 180˚.
3. Slide the old water filter cartridge straight out of the housing and
discard it. (Diagram 2).
4. Unwrap the new filter cartridge and using the alignment guide,
slide it gently into filter housing until it stops against the filter
connection at the back of the housing. (Diagram 3).
5. Engage the filter by firmly rotating clockwise until the filter snaps
into position (once engaged the filter cannot be rotated further).
(Diagram 4).
6. Press a drinking glass against the water dispenser while checking
for any leaks at the filter housing. Any spurts and sputters that
occur as the system purges air out of the dispenser system
are normal.
7. After filling one glass of water, continue flushing the system for
about four minutes.
8. Turn on the ice maker. (Diagram 5).
9. When the filter has been replaced press and hold the ‘Ice and
Water’ button for three seconds to reset the filter replace timer.
PureSou rce
U l t r a 2
Ice & Water Filtration System
PureSou rce
U l t r a 2
Ice & Water Filtration System
PureSou rce
U l t r a 2
Ice & Water Filtration System
Diagram 2
Diagram 3
Diagram 4
Diagram 1
Diagram 5

15REMOVING FEATURES
USING YOUR REFRIGERATOR
Refrigerators work by transferring heat from the food
inside to the outside air. This operation makes the back
and sides of the refrigerator feel warm or even hot
particularly at start-up and on warm days – this is normal.
Avoid placing food against the air vents in the refrigerator
as it affects efficient circulation. If the door is opened
frequently, a light frosting will occasionally occur on the
freezer’s interior. This is normal and will clear after a few
days. If the freezer door is accidentally kept open, a heavy
frost will coat the inside walls and should be removed.
Your new refrigerator uses a high-speed compressor,
along with other energy-efficient components, which may
make unusual sounds and be more noticeable at night
and quieter times. These sounds simply indicate your
refrigerator is working how it should. They include:
• Compressor running noises;
• Air movement noise from the small fan motor;
• A gurgling sound, similar to water boiling;
• A popping noise, heard during automatic
defrosting; and
• A clicking noise, prior to compressor start-up.
Further details can be found in the Troubleshooting Guide.
TIPS & INFORMATION
IMPORTANT
For top mount refrigerators (where the freezer is
on top of the fresh food compartment).
• Don’t place food forward of the ribs on the freezer
floor, as it will keep the door open.
Ribs
For bottom mount refrigerators (where freezer is below
the fresh food compartment):
• Ensure all freezer drawers and shelves are pushed
back completely to prevent them from keeping the
door open.
Crisper Bin
Removal (standard Crisper Bins):
1. Empty food from the crisper. On some models it will
be necessary to remove the bottle storage bins.
2. Remove the crisper bin(s) by pulling forward, then up
and forward again.
3. For top mount and single door, remove the crisper
shelf by lifting the catches on the left and right
underside of the shelf and pulling the shelf forward.
SpillSafe™ glass shelves
To remove the shelves,
gently pull them forward
until the shelf comes
clear of the shelf guides.
To return the shelf, make
sure there is nothing
behind that may obstruct
movement. Gently push the
shelf, into the cabinet and
back into position.
Freezer shelf
Remove the freezer shelf
by lifting the catches on
the right and left underside
of the shelf to release the
shelf then pull the shelf
toward you.
REMOVING FEATURES
CATC H

16 REMOVING FEATURES
Drawers fitted with telescopic slides
To remove the drawer for cleaning.
1. Empty food from the drawer.
2. Remove the drawer by pulling it forward and lifting
the front to unhook it from the slides. Once you have
removed the drawer, ensure the slides are pushed
back so they are fully closed.
WARNING
WARNING
Never close the door while the telescopic slides are
extended. This may damage the slide and/or refrigerator
or cause the slide to become disengaged from the
refrigerator.
To replace the drawer:
1. Ensure the telescopic slides are pushed in all the way.
2. Slide the drawer into place over the slides and push
the bin in until it stops.
3. Drop drawer into position.
Freezer bottom bin
To remove the bin, pull the drawer out until it is open all
the way then lift bin out from the front of the bin. When
refitting insert the rear of the bin first then lower into
position.
When replacing the bins after cleaning, we recommend
fitting the lower bin first.
WARNING
CAUTION
Never close the door while the telescopic slides
are extended. It may damage the slide and/or the
refrigerator or cause the slide to become disengaged
from the refrigerator.
REMOVING FEATURES
Twist and Serve Ice
Mounting the twist & serve dispenser to the other side of
the freezer.
NOTE: this is only possible on Top mount models.
1. Remove the ice bin and ice cube tray. If the ice tray
assembly is frozen to the carriage, simply squeeze
the tray and shelf together to break the ice.
2. Before you remove the ice carriage, remember to
disengage it from the glass shelf as it may result in
damage to the assembly.
3. Remove the centre runner by disengaging it at the
front of the shelf, and removing it from the rear.
4. Refit the runner into the rear of the shelf on the right
hand side and then engage the front.
Insert into the slot at the rear
of the shelf
Then engage into the front of
the shelf
5. Fit the carriage by sliding it into the runners until the
front if the carriage engages with the shelf.
6. Refit the ice tray and ice bin.
WARNING
WARNING
Fill the ice cube tray with potable water only.

17TEMPERATURE CONTROL
TEMPERATURE CONTROL
The factory default settings;
Top mount
Refrigerator Mid
Freezer Mid
Bottom mount & French door
Refrigerator 3°C
Freezer -18°C
All Refrigerator Mid
All Freezer -18°C
If you want to change the temperature, follow the
instructions in the section about the user interface for
your model. Ensure that you make only small adjustments
and wait 24 hours to see if it’s correct to your liking.
TIPS & INFORMATION
IMPORTANT
NOTE: When you set a temperature, you set an average
temperature for the whole refrigerator cabinet.
Checking the softness of ice cream is a good indication
that your freezer is the right temperature, while checking
the temperature of water kept in the refrigerator is a
good way of checking the temperature of the food
compartment.
Temperatures inside each compartment may vary,
depending on how much food you store and where you
place it.
High or low room temperature may also affect the actual
temperature inside the refrigerator.
Top mount freezer temperature adjustment
1. Select the freezer control.
2. Slide the control to the right (as per image below).
3. Slide the control to the left (as per image below).
Set to less coldSummer (>35°c)
Normal
Winter (<15°c) Set to colder
FREEZER TEMPERATURE SETTING RECOMMENDATION

18
Controls – Top mount and single door refrigerator models
Refrigerator
temperature
scale icons
Quick chill on/
off icon
Temperature
adjust/quick
chill on/off
button
DESCRIPTION OPERATION / PRIMARY FUNCTION
Refrigerator temperature scale icons • Indicates the temperature setting of the refrigerator compartment.
Quick Chill On/ Off icon • Indicates the status of the Quick Chill function
Temperature adjust/ quick chill on/
off button
Temperature Control
• Touch the ‘Temp’ button to awaken control.
• Touch the ‘Temp’ button to decrease the refrigerator temperature. There
are 8 temperature settings indicated by the illumination sequence on
the display. Once the coldest temperature is reached the display will
return to the warmest setting with the next press.
Quick Chill
- Use the quick chill function when you add a large amount of food to the
refrigerator compartment.
• Press and hold the ‘Temp’ button for 3 seconds. The Quick Chill icon will
flash indicating that the Quick Chill is active.
• Your refrigerator will run at 2°C for 90 minutes, then automatically return
to normal mode.
• The Quick Chill function can be cancelled anytime by pressing the
‘Temp’ button again.
TIPS & INFORMATION
IMPORTANT
The factory default settings for the refrigerator is “Mid”.
If you want to change the temperature, remember to
make only small adjustments and wait 24 hours to see
if it’s correct.
USER INTERFACE
ABOUT THE USER INTERFACE

19USER INTERFACE
Refrigerator
temperature
scale icons
Quick freeze
on/off icon
Temperature
adjust
Refrigerator
indication
icon
Compartment
select button
Freezer
temperature
scale icons
Quick
freeze button
Quick freeze
on/off icon
Freezer
indication
icon
Controls – Bottom mount and French door
DESCRIPTION OPERATION / PRIMARY FUNCTION
Quick Freeze on/ off icon • Indicates the status of the Quick Freeze function.
Quick Freeze button Use the Quick Freeze function when you add a large amount of food to the
freezer compartment.
• Press the ‘Quick Freeze’ button. The Quick Freeze icon will flash indicating that
the quick freeze is active and the compressor will run continuously for
90 minutes.
• After 90 minutes the freezer will automatically return to normal mode.
• The Quick Freeze function can be cancelled anytime by pressing the
button again.
Refrigerator / Freezer
temperature scale icons
• Indicates the temperature setting of the refrigerator compartment.
• Indicates the temperature setting of the freezer compartment.
Temperature adjust button • Touch any button to awaken control.
• Touch the ‘Temp’ button to decrease the selected compartment temperature.
There are 8 temperature settings indicated by the illumination sequence on the
display. Once the coldest temperature is reached the display will return to the
warmest setting with the next press.
Refrigerator/Freezer
indication icon
• Indicates the selected zone.
Compartment select button • Press to select the desired compartment.
• The refrigerator / freezer indication icon will show which zone is selected.
TIPS & INFORMATION
IMPORTANT
The factory default settings for the refrigerator is “3°C” and “-18°C” for the freezer. If you want to change the
temperature, remember to make only small adjustments and wait 24 hours to see if it’s correct.

20 USER INTERFACE
ABOUT THE USER INTERFACE
Controls – Bottom mount ice & water and French door ice & water models
1
23
5
4
6
9
8
11
7
10
12
15
13
14
BUTTON /
ICON
DESCRIPTION PRIMARY FUNCTION
1Compartment Selector button Selects controllable compartment.
2Lock Icon Indicates if the user interface is locked.
3Compartment Icon Indicates controllable compartment.
4ECO Icon Indicates if the appliance is operating in its most energy
efficient mode.
5Digital display Indicates temperature of selected compartment.
6Increase button Increases temperature of selected compartment.
7Decrease button Decreases temperature of selected compartment.
8Mode indicators (Shopping, Quick
Freeze, Holiday)
Indicates appliance operation mode.
9Display Lock button Selects lock state of user interface.
10 Mode select button Selects operation mode of appliance.
11 Drinks Chill button Selects drinks chill timer.
12 Filter status indicators Indicates filter replacement timing.
13 Icemaker and Water on off indicators Shows operational status .
14 Ice & Water on/off button Selects operational status.
15 Door sensor Senses door state (open or closed).