Westlab WJH0362A User manual

1
PRODUCT MANUAL
Code WJH0362A
Laboratory
Draining Rack
Wall Mounted, 52 Slots, Grey

2
PRODUCT MANUAL
1800 358 101
sales.au@westlab.com
www.westlab.com.au
+64 9 553 3677
sales.nz@westlab.com
www.westlab.co.nz
646 568 5391
sales.us@westlab.com
www.westlab.com
1 877 822 1455
sales.ca@westlab.com
www.westlab.com
Australia New Zealand United StatesCanada
1. Product Description
1.1 Introduction
The Laboratory Draining Rack is a wall-mounted pegboard with 52 removable pegs.
For improved load bearing, the peg sockets can be secured to the rack by pushing in and
then down. Additionally, the pegs are easily removable for cleaning or modifying the peg
arrangement.
The bottom of the bracket has a sloping design for the liquid to drain seamlessly through
the built-in drainage system. The supplied draining hose can be connected to the liquid
outlet at the rear of the unit.
For added convenience, two of the draining racks can be combined to create a double-
sided benchtop draining rack.
1.2 Intended Use
Ideal for post-wash draining and drying of laboratory glassware and labware.
Applicable for use within the laboratory, medical, chemical, quality testing, schools,
and research institutions.
1.3 Features
• Laboratory Draining Rack, Wall Mounted, Single Sided
• Manufactured from Polypropylene
• 56 Removable Pegs Supplied
• Built-In Drainage System
• 52 Slot Positions
• Grey Colour
1.4 Accessories
Description
Qnty for Wall
Mounted Option
Qnty for Bench
Mounted Option
Peg, 120mm 28 56
Peg, 140mm 28 56
Slot Cover 3 6
Upper Bracket 2 2
Middle Bracket 0 2
Lower Bracket 0 2
TABLE OF CONTENT
1. Product Description
1.1 Introduction
1.2 Intended Use
1.3 Features
1.4 Accessories
2. TechnicalSpecications
3. Installation
4. Product Disposal
PRODUCT CODE
WJH0362A
PLEASE READ THESE INSTRUCTIONS BEFORE USE.

3
PRODUCT MANUAL
1800 358 101
sales.au@westlab.com
www.westlab.com.au
+64 9 553 3677
sales.nz@westlab.com
www.westlab.co.nz
646 568 5391
sales.us@westlab.com
www.westlab.com
1 877 822 1455
sales.ca@westlab.com
www.westlab.com
Australia New Zealand United StatesCanada
Description
Qnty for Wall
Mounted Option
Qnty for Bench
Mounted Option
Lower Bracket 1 0
L Type Connector 1 2
Y Type Connector 0 1
Plastic Rivet 6 12
Screw & Plastic Sleeve 6 12
Draining Hose, 1 Metre 1 1
2. Technical Specication
Material Polypropylene [PP]
Colour Grey
Mounting Type Wall mounted
Available Peg Slots 52
Pegs Supplied Total of 56 pegs supplied
Draining Capability Yes, built-in draining hole
Unit Dimensions 700mm x 550mm x 120mm
Unit Weight 2.68kg
Carton Quantity 1
Carton Dimensions 725mm x 585mm x 190mm
Carton Weight 6.94kg
3. Installation
1. Open the packaging and remove the draining rack from the box.
2. Unpack every individual component.
3. Assemble the components as instructed in this manual for optimal performance.
Peg installation and removal
As shown below, push the peg into a hole and then press down.

4
PRODUCT MANUAL
1800 358 101
sales.au@westlab.com
www.westlab.com.au
+64 9 553 3677
sales.nz@westlab.com
www.westlab.co.nz
646 568 5391
sales.us@westlab.com
www.westlab.com
1 877 822 1455
sales.ca@westlab.com
www.westlab.com
Australia New Zealand United StatesCanada
For removal, pull the peg upward and then pull out.
The120mmpegsarerecommendedtobettedintotheholes
of the bottom four rows
Mounting to a wall
# Description Qnty for Wall Mounting
1 Peg, 120mm 28
2 Peg, 140mm 28
3 Slot Cover 3
4 Upper Bracket 2
5 Middle Bracket 0
6 Lower Bracket 0
7 Lower Bracket 1
8L Type Connector 1
9Y Type Connector 0
10 Plastic Rivet 6
11 Screw & Plastic Sleeve 6
12 Draining Hose, 1 Metre 1

5
PRODUCT MANUAL
1800 358 101
sales.au@westlab.com
www.westlab.com.au
+64 9 553 3677
sales.nz@westlab.com
www.westlab.co.nz
646 568 5391
sales.us@westlab.com
www.westlab.com
1 877 822 1455
sales.ca@westlab.com
www.westlab.com
Australia New Zealand United StatesCanada
1. Install the upper brackets as shown above.
2. Install the lower mounting kit as shown above. Tighten the plastic rivets with
a Phillip screwdriver or press them into the holes.
3. Connect the L type connector and the draining hose as shown above.
4. Hooking the pegboard:
i. Drill two holes into the wall according to the dimensions shown on the
bottom left of the above graphic.
ii. Screw the plastic sleeves and screws until the two screw heads are
3mm to 4mm from the wall.
iii. Hook the pegboard.
iv. After marking the two positions of the fastener holes of the mounting
brackets on the wall, remove the pegboard again.
v. Drill the marked positions to insert the plastic sleeves.
vi. Hook the pegboard again.
vii. Tighten the screws via the holes of the bracket.
NOTE! For mounting on a wooden wall, tighten the screws only.

6
PRODUCT MANUAL
1800 358 101
sales.au@westlab.com
www.westlab.com.au
+64 9 553 3677
sales.nz@westlab.com
www.westlab.co.nz
646 568 5391
sales.us@westlab.com
www.westlab.com
1 877 822 1455
sales.ca@westlab.com
www.westlab.com
Australia New Zealand United StatesCanada
Mounting to a bench
# Description Qnty for Bench Mounting
1 Peg, 120mm 56
2 Peg, 140mm 56
3 Slot Cover 6
4 Upper Bracket 2
5 Middle Bracket 2
6 Lower Bracket 2
7 Lower Bracket 0
8L Type Connector 2
9Y Type Connector 1
10 Plastic Rivet 12
11 Screw & Plastic Sleeve 12
12 Draining Hose, 1 Metre 1

7
PRODUCT MANUAL
1800 358 101
sales.au@westlab.com
www.westlab.com.au
+64 9 553 3677
sales.nz@westlab.com
www.westlab.co.nz
646 568 5391
sales.us@westlab.com
www.westlab.com
1 877 822 1455
sales.ca@westlab.com
www.westlab.com
Australia New Zealand United StatesCanada
1. Install the upper bracket as shown above.
2. Install the middle bracket as shown above.
3. Install the lower bracket as shown above. Tighten the plastic rivets with
a Phillip screwdriver or press them into the holes.
4. Connect the L type connector and the draining hose as shown above.
5. Draining hose:
i. Cut off two short hose lengths.
ii. Connecting the two L type and Y type connectors in the order
as shown above.
iii. Tighten the screws via the holes of the lower bracket.
Cover installation
Fortheholeswithoutpegs,llthemwiththeslotcovers.
For the removal of the slot covers, insert the tips of a screwdrivers into the small,
recessed hole at the bottom of the cover.
4. Product Recycling
In the case that the product is to be disposed of, the relevant legal regulations are
to be observed.
ORDERING WITH
WESTLAB IS EASY
Online
www.westlab.com.au
Order online with our easy
Express Order form for fast,
secure ordering.
Phone
1800 358 101
Speak to one of our friendly,
ecientstafffrom
8.00am - 5.00pm (Mon/Fri)
Email
24 hours, 7 days a week
convenience.

Westlab in every discovery.
Table of contents
Popular Rack & Stand manuals by other brands

ICWUSA
ICWUSA Ultra 210 Series installation instructions

Roland
Roland KS-307 Assembly

Cavus
Cavus CMBOM5 Mounting instructions

Extron electronics
Extron electronics PoleVault Systems PVS 300 installation guide

TOOLCRAFT
TOOLCRAFT 2265279 Assembly instruction

Eagletone
Eagletone STUDIODEN RACK Assembly instructions