Whirlpool ADP 6940 IXM User manual

SERVICE Whirlpool Europe
Customer Services
Model ADP 6940 IXM
Version 8542 940 53930 Page
Technical data 2 - 4
Spare part list 5 - 6
Exploded view 7 - 8
Circuit diagram 9
Program diagram 10
Text/Legend 11 - 17
Family EBL - TOP5
Sensor+
Service Manual
Dishwasher
ADP 6940 IXM
ADP 6940 IXM
This documentation is only intended for qualified technicians who are aware of the respec-
tive safety regulations.
Date: 23.10.2006 Subject to modification
Document-No.: 4812 728 12449

SERVICE
23.10.2006 / Page 2 ADP 6940 IXM Whirlpool Europe
Doc. No: 4812 728 12449 8542 940 53930 Customer Service
Technical data
Dimension
Height 85,0 cm ±1.4
Width 59.7 cm
Depth 61.0 cm
Weight 58 kg
Electronic boards
Service boards see spare part list
Serial boards see on the boards itself
DB 4619 724 86772
UB 4619 724 86782
Programing of version and programmed control
board, see „Service“ and „Data set“ on rating
plate of inner door:
CB programmed 739895
Data set 739885
Basic control board, not programmed see on the
board itself 4619 727 50131
For programing please use Service Assistance
Module (S.A.M.) 4812 289 98001
plus cable 4812 289 98004
Succession of programs
Programs see program diagram
Succession A1a-A2a-A3a-A5h-A10a
Alarms
Refill rinse aid
Options
Sani rinse
Zone washing
Program information (LCD)
Start indicator
Pre wash
Main wash
Drying
End
All programs will be locked after start. Changing
the program or finishing the program will be
possible only after pressing the start button for
longer then 1.5 sec. (Break by customer)
A switching off the appliance or unplug the
appliance for a while, this will frozen the program
step and later on, the program continuos on the
same position.
Exception: Switching off the appliance or unplug
the appliance during the drying phase, this will lead
directly to the end of the program.
Water Volume at alternate spray system
Volume at alternating spray system (same level
when selected zone washing as in the normal
programs)
Water Volume Level
Regeneration 0.3 l 15 mm
Back rinse 3x 1.0 l 60 mm
Prewash 3.9 l 120 mm
Main wash 3.2 l 118 mm
Intermediate rinse 1 3.2 l 118 mm
Intermediate rinse 2 3.2 l 118 mm
Clear rinse 3.2 l 118 mm
Safety/ overflow 8.5 l 141 mm
Measuring the level
Remove the coarse sieve, put in a measuring
meter into the sump, measure the hight of the
water level.
Detergent max.
Pre-wash 10 cm3
Main-wash 40 cm3
Rinse aid 135 cm3
6 Dosage steps 1 - 6 ml
Water pressure
Inlet pressure 0.3 - 10 bar
Spray pump pressure 0.3 bar
Rotations
Spray pump motor 2800 RPM
Drain pump motor 3000 RPM
Spray arm lower 30 - 40 RPM
Spray arm upper 30 - 40 RPM

SERVICE Whirlpool Europe ADP 6940 IXM 23.10.2006 / Page 3
Customer Service 8542 940 53930 Doc. No: 4812 728 12449
Technical data
Spray arms, turning rhythm at alternating spray
system
Turning starts every time with the upper spray arm
Pre wash Lower arm ~3min, Upper arm ~1min
Main wash Lower arm ~3min, Upper arm ~5min
Intermediate rinse
Lower arm ~2min, Upper arm ~2min
Final rinse Lower arm ~2min, Upper arm ~2min
Service Test program
Lower arm ~30sec, Upper arm ~30sec
Remark: When switching of the main switch or
interrupt the mains during the Test Program runs,
then the alternating of the spray arms change in
the test program to the rhythm of main wash 5/3
min.
Important: To leaf the Test program is possible by
made a break by customer (pushing the start
button for 1.5 sec.)
After finishing the test program (End LED shines
and/or Start LED goes of) must the appliance be
switched off.
If this will not be done, then the next normal wash
will be made with the frequency of the Service
Test Program ~30/30sec.
Flow rates/ Inlet volume
Flow meter (at 0.3 bar
= quantity 1.1 l/min) 208 lmp/l
Spray pump 45 - 65 l/min
Drain pump 16 l/min
Pump height max. 1.1 m
Inlet valve 4 l/min
Spray arm lower ~ 33 l/min
Sprayarm upper ~ 27 l/min
Shower/ Sprayarm top ~ 8 l/min
Electrical base data
Voltage 240 V
Frequency 50 Hz
Total power 2.4 kW
Fuse 10 A
Spray pump motor alternating spray system
Voltage 220/ 240 V
Power consumption 125 W
HI 79 Ω
HA 60 Ω
Capacitor 4 µF
Drain pump motor
Voltage 220/ 240 V
Power consumption 30 W
Resistance 146 Ω
Heating - 1 Element system
Voltage 240 V
Power consumption 2.22 kW
Resistance 24.5 Ω
Heating speed ~ 2.0 ˚C/min
Temperature on surface ~ 115 ˚C
Safety thermostat self reset
(Temperature of water) ~ 85 ˚C
Fuse 206 ˚C
Single electric water inlet valve
Voltage 220/ 240 V
Frequency 50/ 60 Hz
Resistance 3.76 kΩ
Motor Diverter Valve
Voltage 220 - 240 V
Frequency 50/ 60 Hz
Resistance 6.5 kΩ
Signal (2x within ~13 sec.) 5.0 V
Coil of dispenser
Voltage 220/ 240 V
Frequency 50/ 60 Hz
Resistance 1.3 kΩ
Reed contacts
flow meter
rinse aid control
Optical water indicator (OWI)
Optical measurement of the water in sump
Combination part of:
Turbidity sensor (DON)
Thermostat temp. sensor (notice NTC)

SERVICE
23.10.2006 / Page 4 ADP 6940 IXM Whirlpool Europe
Doc. No: 4812 728 12449 8542 940 53930 Customer Service
Technical data
NTC
20 ˚C 58.1 kΩ
25 ˚C 47.1 kΩ
30 ˚C 38.2 kΩ
40 ˚C 25.4 kΩ
50 ˚C 17.2 kΩ
60 ˚C 11.8 kΩ
70 ˚C 8.3 kΩ
80 ˚C 6 kΩ
85 ˚C 4 kΩ
Regeneration
Volume 300 cm3
after wash cycles depending on the water hardness
water hardness 0 - 60 (53) ˚dh
0 - 10.7 mmol/l
0 - 107 ˚Fh
Salt consumption for regeneration ~ 77 g
Number of cycles with 2 kg salt ~ 26
Water softener setting
To change the water softener setting:
• Push the POWER button on
• Change to program 2
• Hold the START button for 5 seconds until the LED is flashing
• Water softener setting is shown by flashing LED or digital display
• By pushing the START button you can change the setting
• Push the POWER button off to save and exit the water softener setting
Accesory
If you need spare parts apart from the spare part list have a look in the Service Bulletin 4812 718 40084.
For higher mounted Dishwashers to prevent the drain off effect - also usable for lower drain pipes and to
prevent the failure F8 use Kit 4812 310 18993.
Water hardness Germandegrees
˚dH French degrees ˚fH English degrees Clarke ˚e mmol/l Water softener setting is shown by flashing LED (1x-7x)
or digital display (1-7)
1 soft 0 - 5 0 - 9 0 - 6,3 0 - 0.9 1 x
1 - 2 soft/ medium 6 - 10 10 - 18 7 - 12.6 1 - 1.8 2 x
2 medium 11 - 15 19 - 27 13.3 - 18.9 1.9 - 2.7 3 x
3 medium/ hard 16 - 21 28 - 37 19.6 - 25.9 2.8 - 3.7 4 x (DEFAULT SETTING)
4 hard 22 - 28 38 - 50 26.6 - 35 3.8 - 5.0 5 x
4 very hard 29 - 35 51 - 63 35.7 - 44.1 5.1 - 6.3 6 x
4 extremely hard 36 - 60 (53) 64 - 107 44.8 - 74.9 6.4 - 10.7 7 x

SERVICE Whirlpool Europe ADP6940IXM 23.10.2006 / Page 5
Customer Service 8542 940 53930 Doc. No: 4812 728 12449
Spare part list
Model ADP 6940 IXM
Service No. 854294053930
Version 854294053930
Pos. No. 12NC Code Description
003 0 4812 440 19594 Crossbar
004 0 4812 440 18952 Drip tray assy
004 1 4812 401 18402 Holder
011 0 4812 505 18357 Foot short
022 1 4812 440 11343 Side panel le/ri INOX
024 0 4812 440 10417 Panel rear
030 0 4812 310 19006 Table top cpl. INOX
034 0 4812 404 78237 Spacer
040 1 4812 417 18774 Hinge left
040 2 4812 417 18773 Hinge right
040 3 4812 417 19282 Protector f.door (set)
044 0 4812 492 38358 Spring f.door
047 0 4812 404 48746 Brake f.door
047 1 4812 401 18397 Band,brake
047 2 4812 404 68023 Hook
053 0 4812 440 89025 Plinth SIL
053 4 4812 440 89107 Plinth rounded INOX
061 0 4812 466 88672 Counter weight
065 0 4812 466 48051 Insulation without outcut
103 0 4812 310 19019 Door outer INOX EBL Kit
120 0 4812 440 19456 Door inner
120 1 4812 440 18969 Batten
130 0 4812 417 58392 Tilt lock cpl. wh
131 0 4812 401 18416 Hook lock
191 0 4812 466 68564 Gasket door
191 3 4812 466 68533 Gasket
192 0 4812 466 68467 Gasket door lower
241 0 4812 458 19249 Basket upper straight
241 1 4812 458 19246 Holder cups saph EBL
241 2 4812 535 78081 Bearing holder cups saph EBL
241 3 4812 528 88113 Wheel,basket upper (set)
241 6 4812 458 19251 Holder glasses wiring silv.EBL
242 0 4812 458 19248 Basket lower cpl.
242 1 4812 528 88112 Wheel,basket lower
242 6 4812 458 19252 Support plate left
242 7 4812 458 19253 Support plate right
243 0 4812 458 19276 Cutlery basket
243 5 4812 310 38897 Cutlery basket KIT
243 6 4812 458 19296 Grille saphire
261 0 4812 462 79831 Rail telescope, inner
261 1 4812 462 79768 Cap rail rear saph.
261 2 4812 462 79904 Cap swinging, rail ahead
263 0 4819 520 18013 Ball cage cpl.
263 1 4812 310 48026 Service kit balls plastic
265 0 4812 404 48917 Basket adjustm. cpl.
265 2 4812 404 48918 Grip basket adjustment
265 3 4812 404 48931 Grip cpl.
301 0 4812 453 73052 Control panel INOX
303 1 4812 460 58396 Handle
331 0 4812 410 29234 Knob INOX
332 0 4812 410 29232 Button INOX
332 1 4812 410 29233 Button INOX
332 3 4812 410 29235 Button ON/OFF INOX
350 0 4812 276 58148 Display board (DB)
400 0 4812 361 58336 Motor +SP,50Hz,alt.LP-PNT1
Pos. No. 12NC Code Description
405 0 4812 360 18543 Pump body alt. CESET
420 0 4812 121 18132 Capacitor
421 0 4812 121 18158 Interf.filter
430 0 4812 360 18508 Pump,draining cpl.
430 1 4812 466 68689 Gasket
450 0 4812 259 28684 Heating element
480 0 4812 321 28432 Cable harness EBL high
480 3 4812 401 18418 Protector f.wiring
490 0 4812 321 18051 Cable mains
490 1 4812 321 28367 Strain relief
521 0 4812 214 79577 Control board (CB)
583 0 4812 271 28537 Switch diaphragm (OWI)
616 1 4812 271 58161 Contact,reed rinsing agent
620 0 4812 218 38235 User board (UB)
621 0 4819 410 29004 Switch ON/OFF
623 0 4812 271 38356 Microswitch
633 0 4812 271 38355 Microswitch door
680 0 4812 418 68364 Combidosage cpl.
680 1 4812 466 68495 Gasket
680 3 4812 440 11209 Lever,fastener combidos.
681 1 4812 466 68497 Gasket
681 2 4812 440 18975 Flap
682 0 4812 466 68496 Gasket
691 1 4812 462 79769 Stopper NTC
700 0 4812 530 29385 Hose inlet aqua stop
700 1 4812 480 48096 Sieve
700 2 4812 466 68628 Gasket
701 1 4812 310 18153 Yoke clamp set
710 2 4812 310 38896 Threaded ring
710 3 4819 466 69562 Gasket set
714 0 4812 462 79921 Threaded cap
716 0 4812 418 68142 Reg.dosage
716 1 4812 466 68475 Gasket
716 2 4812 462 78994 Cover
717 0 4812 281 28431 Valve motordiverter
717 2 4812 528 98011 Valve disk diverter
717 3 4812 530 29121 Gasket diverter valve
721 1 4812 360 68689 Spray arm lower. cpl. sa
722 0 4812 360 68687 Spray arm upper sa
722 2 4812 360 68688 Spray arm 2nd level cpl. saph
723 0 4812 360 68691 Douche ceiling
726 1 4812 530 29331 Tube assembly cpl.saph
726 2 4812 505 18208 Nut
743 0 4812 511 48171 Condenser
743 1 4812 530 28102 Hose inlet
743 3 4812 462 79857 Cover
743 4 4812 530 28807 Hose 9x1,5x270+10
743 7 4812 466 68514 Gasket
751 0 4812 418 18338 Water collector
755 0 4812 530 29119 Bend
755 2 4812 530 48148 Tray leak
756 0 4812 360 58099 Floater
761 0 4812 480 58122 Sieve fine
761 2 4812 418 18337 Cover sieve
761 3 4812 418 18341 Cover

SERVICE
23.10.2006 / Page 6 ADP6940IXM Whirlpool Europe
Doc. No: 4812 728 12449 8542 940 53930 Customer Service
Spare part list
Model ADP 6940 IXM
Service No. 854294053930
Version 854294053930
Pos. No. 12NC Code Description
761 4 4812 530 58141 O-Ring
763 0 4812 480 58123 Sieve coarse
781 0 4812 530 29113 Hose draining
781 3 4812 281 28417 Flap non-return
783 6 4812 530 28824 Hose 10,3X3X245
791 0 4812 532 68099 Gasket
901 0 4822 401 10258 Clamp hose 10-18 mm
901 1 4812 401 18424 Strap 050,0
901 2 4812 401 18157 Strap 32-50/9 C61
901 5 4812 401 48573 Strap 028,6
904 4 4812 462 79659 Threaded cap
910 1 4812 502 38152 Screw 4.8x19
910 2 4812 502 18363 Screw 4,0x12-H
910 3 4812 502 18389 Screw 5x20 T20
910 4 4812 502 18385 Screw M3,5x8-T15M
910 5 4812 502 18393 Screw 3,5x9-1 Tx15
910 7 4812 502 18397 Screw INOX A2 M 5X12
910 8 4812 502 18527 Screw 4x15 T20
964 0 4812 466 68577 Gasket housing ri/le grey
964 1 4812 466 68576 Gasket housing upper grey
993 0 4819 530 29028 Bow

SERVICE Whirlpool Europe ADP 6940 IXM 23.10.2006 / Page 7
Customer Service 8542 940 53930 Doc. No: 4812 728 12449
Exploded view

SERVICE
23.10.2006 / Page 8 ADP 6940 IXM Whirlpool Europe
Doc. No: 4812 728 12449 8542 940 53930 Customer Service
Exploded view

SERVICE Whirlpool Europe ADP 6940 IXM 23.10.2006 / Page 9
Customer Service 8542 940 53930 Doc. No: 4812 728 12449
Circuit diagram
3in1 Multi-tablet Micro switch (3in1)
ASA/ Automatic salt adaption/ WHS Water hardness sensor C1 Capacitor CB Control board CULCD Control unit LCD DB Display board DUB Display- and User board DLB Timerswitch Delay DPM Drain pump motor DD Cleaning agent dosage DON Turbidity sensor DR Final rinse dosage DS Door switch DVH Diverter ventil high DVL Diverter ventil low FM Flow meter HEWI Heating IF Interference filter LS6 Water leakage switch L Line M Motor MS Main switch NTC Thermostat temp. sensor N Neutral OWI Water indicator, optical PRG Plug to program RV Water hardness switch RE Heating relay RE2 Mix valve for Regeneration RR SA Reed relay salt RR RA Reed relay rinsaid SPM Sprayarm motor THS1 Safety thermostat THS 2 Fuse TBL Power supply terminal TL Winding protective
contact
UB User board UCB User- and Control board UDB User- and Display board VM Fan ventilator VSM Variable speed Motor WV1 Water inlet valve WV2 Water regenerating valve WI Water indicator 00 black 66 blue 88 grey 99 white

SERVICE
23.10.2006 / Page 10 ADP 6940 IXM Whirlpool Europe
Doc. No: 4812 728 12449 8542 940 53930 Customer Service
Program diagram

SERVICE Whirlpool Europe ADP 6940 IXM 23.10.2006 / Page 11
Customer Service 8542 940 53930 Doc. No: 4812 728 12449
Text/Legend

SERVICE
23.10.2006 / Page 12 ADP 6940 IXM Whirlpool Europe
Doc. No: 4812 728 12449 8542 940 53930 Customer Service
Text/Legend

SERVICE Whirlpool Europe ADP 6940 IXM 23.10.2006 / Page 13
Customer Service 8542 940 53930 Doc. No: 4812 728 12449
Text/Legend

SERVICE
23.10.2006 / Page 14 ADP 6940 IXM Whirlpool Europe
Doc. No: 4812 728 12449 8542 940 53930 Customer Service
Text/Legend

SERVICE Whirlpool Europe ADP 6940 IXM 23.10.2006 / Page 15
Customer Service 8542 940 53930 Doc. No: 4812 728 12449
Text/Legend

SERVICE
23.10.2006 / Page 16 ADP 6940 IXM Whirlpool Europe
Doc. No: 4812 728 12449 8542 940 53930 Customer Service
Text/Legend

SERVICE Whirlpool Europe ADP 6940 IXM 23.10.2006 / Page 17
Customer Service 8542 940 53930 Doc. No: 4812 728 12449
Text/Legend