Whirlpool DWH B80 W User manual

SERVICE Whirlpool Europe
Customer Services
Model DWH B80 W
Version 8542 400 53000 Page
Technical data 2 - 3
Spare part list 4 - 5
Exploded view 6 - 7
Circuit diagram 8
Program diagram 9
Text/Legend 10 - 15
Family WRC - IC
MID 5
Service Manual
Dishwasher
integratable fulldor
DWH B80 W
601 186 43
DWH B80 W
This documentation is only intended for qualified technicians who are aware of the respec-
tive safety regulations.
Date: 21.02.2007 (Mod. 01) Subject to modification
Document-No.: 4812 728 14196

SERVICE
21.02.2007 (Mod. 01) / Page 2 DWH B80 W Whirlpool Europe
Doc. No: 4812 728 14196 8542 400 53000 Customer Service
Technical data
Dimension
Height 82.0 - 87.0cm
Width 59.7 cm
Depth 57.0 cm
Weight 50 kg
Wooden door for Full Door appliances
Thickness min. 16 mm
Thickness max. 20 mm
Width min. 592 mm
Width max. 595 mm
Height min. 620 mm
Height max. 718 mm
Weight min. 2.5 kg
Weight max. 6.5 kg
Max. stick out over lower
edge of appliance door 92 mm
Height of plinth min. 93 mm
Electronic boards
Service boards see spare part list
Serial boards see on the boards itself
Programing of version and programmed control
board, see „Service“ and „Data set“ on rating
plate of inner door:
UCB (User/Control board) 53481
Data set 53471
Basic UCB (User/Control board) not programmed
see on the board itself 4619 727 14212
For programing please use Service Assistance
Module (S.A.M.) 4812 289 98001
plus cable 4812 289 98004
Succession of programs
Programs see program diagram
Succession P1a-P3a-P5k-P11a-P7b
Datas Energy Label
Reference program P5k
Energy Performance 3 stars
Alarms
Refill rinse aid
Options
Half load
Program information
End - Acoustic signal
All programs will be locked after start. Changing
the program or finishing the program will be
possible only after pressing the start button for
longer then 1.5 sec. (Break by customer)
A switching off the appliance or unplug the
appliance for a while, this will frozen the program
step and later on, the program continuos on the
same position.
Exception: Switching off the appliance or unplug
the appliance during the drying phase, this will lead
directly to the end of the program.
Water Volume at permanent spray system
Water Volume Level
Back rinse 3x 1.0 l 60 mm
Prewash 4.8 l 120 mm
Main wash 4.2 l 118 mm
Intermediate rinse 1 4.2 l 118 mm
Intermediate rinse 2 4.2 l 118 mm
Clear rinse 4.2 l 118 mm
Safety/ overflow 8.5 l 141 mm
Measuring the level
Remove the coarse sieve, put in a measuring
meter into the sump, measure the hight of the
water level.
Detergent max.
Pre-wash 10 cm3
Main-wash 40 cm3
Rinse aid 135 cm3
6 Dosage steps 1 - 6 ml
Water pressure
Inlet pressure 0.3 - 10 bar
Spray pump pressure 0.3 bar
Rotations
Spray pump motor 2800 RPM
Drain pump motor 3000 RPM
Spray arm lower 30 - 40 RPM
Spray arm upper 30 - 40 RPM

SERVICE Whirlpool Europe DWH B80 W 21.02.2007 (Mod. 01) / Page 3
Customer Service 8542 400 53000 Doc. No: 4812 728 14196
Technical data
Flow rates/ Inlet volume
Flow meter (at 0.3 bar
= quantity 1.1 l/min) 208 lmp/l
Spray pump 45 - 65 l/min
Drain pump 16 l/min
Pump height max. 1.1 m
Inlet valve 4 l/min
Spray arm lower ~ 33 l/min
Sprayarm upper ~ 27 l/min
Shower/ Sprayarm top ~ 8 l/min
Electrical base data
Voltage 240 V
Frequency 50 Hz
Total power 2.4 kW
Fuse 10 A
Spray pump motor permanent spray system
Voltage 220/ 240 V
Power consumption 130 W
HI 62 Ω
HA 74,8 Ω
Capacitor 4 µF
Drain pump motor
Voltage 220/ 240 V
Power consumption 30 W
Resistance 146 Ω
Heating - 1 Element system
Voltage 240 V
Power consumption 2.22 kW
Resistance 24.5 Ω
Heating speed ~ 2.0 ˚C/min
Temperature on surface ~ 115 ˚C
Safety thermostat self reset
(Temperature of water) ~ 85 ˚C
Fuse 206 ˚C
Water safty options
Waterstop system Reflex Waterstop
Single electric water inlet valve
Voltage 220/ 240 V
Frequency 50/ 60 Hz
Resistance 3.76 kΩ
Coil of dispenser
Voltage 220/ 240 V
Frequency 50/ 60 Hz
Resistance 1.3 kΩ
Reed contacts
flow meter
rinse aid control
NTC
20 ˚C 58.1 kΩ
25 ˚C 47.1 kΩ
30 ˚C 38.2 kΩ
40 ˚C 25.4 kΩ
50 ˚C 17.2 kΩ
60 ˚C 11.8 kΩ
70 ˚C 8.3 kΩ
80 ˚C 6 kΩ
85 ˚C 4 kΩ
Accesory
If you need spare parts apart from the
spare part list have a look in the
Service Bulletin 4812 718 40084.
For higher mounted Dishwashers to prevent
the drain off effect - also usable for lower drain
pipes and to prevent the failure F8
use Kit 4812 310 18993.

SERVICE
21.02.2007 (Mod. 01) / Page 4 DWHB80W Whirlpool Europe
Doc. No: 4812 728 14196 8542 400 53000 Customer Service
Spare part list
Model DWH B80 W
Service No. 854240053000
Version 854240053000
Pos. No. 12NC Code Description
003 0 4812 440 11455 Crossbar
004 0 4812 440 11463 Drip tray assy
004 1 4812 401 18402 Holder
011 0 4812 505 18418 Foot long
011 1 4812 528 98004 Shaft flexible
011 2 4812 528 78032 Slide disc f.foot
011 3 4812 535 98054 Gear
011 4 4812 528 98001 Roll f.foot
022 0 4812 440 11467 Side panel left metallic
022 1 4812 440 11466 Side panel right metallic
024 0 4812 440 11468 Panel rear
040 1 4812 417 18774 Hinge left
040 2 4812 417 18773 Hinge right
044 0 4812 492 38362 Spring f.door
047 0 4812 404 48746 Brake f.door
047 1 4812 401 18707 Band,brake
047 2 4812 404 68023 Hook
053 0 4812 440 89138 Plinth w/o hohle sheet
065 0 4812 466 48051 Insulation without outcut
103 0 4812 440 11465 Door outer
105 0 4812 404 48611 Fastener door
105 2 4812 505 68022 Clip
105 3 4812 404 48633 Fastener
105 4 4812 310 58116 Template FD
120 0 4812 440 19456 Door inner
120 1 4812 440 11454 Batten
130 0 4812 417 58398 Tilt lock
131 0 4812 401 18416 Hook lock
175 3 4812 466 68867 Batten
191 0 4812 466 68564 Gasket door
192 0 4812 466 68467 Gasket door lower
241 0 4812 458 19027 Basket upper straight
241 1 4812 458 19264 Holder cups right saph.VBL
241 3 4812 528 88113 Wheel basket upper (set)
241 6 4812 310 18757 Holder glasses kit wh
241 6 4812 458 19355 Holder glasses wiring alu.VBL
241 6 4812 535 78095 Bearing wiring glassholder saph.
241 8 4812 466 68848 Spacer saph
242 0 4812 310 28136 Basket lower KIT
242 1 4812 528 88069 Wheel basket lower wh
243 5 4812 310 38897 Cutlery basket KIT
243 6 4812 458 19296 Grille saphire
261 0 4812 462 79831 Rail telescope, inner
261 1 4812 462 79768 Cap rail rear saph.
261 2 4812 462 79902 Cap rail front
263 0 4819 520 18013 Ball cage cpl.
263 1 4812 310 48026 Service kit balls plastic
265 0 4812 404 49712 Basket adjustm. VBL cpl.saph-opaco
265 2 4812 404 48934 Grip basket adj.opaco
301 0 4812 453 71765 Control panel
322 0 4812 453 73459 Insert
332 5 4812 410 28556 Cap f.beater
400 0 4812 361 58434 Motor +SP,50Hz,per.
405 0 4812 360 18568 Pump body Crin Serv.Part
405 2 4812 530 29437 Connection Outlet ServiceKit CRIN
Pos. No. 12NC Code Description
420 0 4812 121 18277 Capacitor
421 0 4812 121 18276 Interf.filter
430 0 4812 360 18558 Pump,draining cpl.
430 1 4812 466 68689 Gasket
450 0 4812 259 28892 Heating element 2,04 kW
480 0 4812 321 28416 Cable harness IC-FD (LS6)
480 1 4812 321 28475 Cable UCB-DB
480 3 4812 401 18418 Protector f.wiring
490 0 4812 321 18051 Cable mains
490 1 4812 321 28367 Strain relief
503 0 4812 282 10183 Timer switch delay 3-6-9(DLB)
521 0 4812 218 38347 Control board SAM BASIC
521 0 4812 218 38556 Control board UCB
571 0 4812 281 28462 Valve inlet
583 0 4812 271 28556 Switch diaphragm
616 1 4812 271 58184 Contact reed rinsing agent
621 0 4812 276 18493 Switch on/off
623 0 4812 271 38489 Microswitch
633 0 4812 271 38488 Microswitch door
680 0 4812 418 68371 Combidosage cpl.w.KSM saph/opaco
680 1 4812 466 68495 Gasket
680 3 4812 440 11209 Lever,fastener combidos.
681 1 4812 466 68497 Gasket
681 2 4812 440 18975 Flap
682 0 4812 466 68496 Gasket
691 0 4812 282 68051 Feeler NTC
701 0 4819 530 28926 Hose inlet 2.5 m (Eltek)
701 1 4812 310 18302 Yoke
701 2 4822 480 50159 Sieve inlet
710 2 4812 310 38896 Threaded ring
710 3 4819 466 69562 Gasket set
714 0 4812 462 79921 Threaded cap
716 0 4812 418 68377 Reg.dosage
716 1 4812 466 68475 Gasket
716 2 4812 462 78994 Cover
717 1 4812 462 79793 Stopper
721 1 4812 360 68689 Spray arm lower. cpl. sa
722 0 4812 360 68687 Spray arm upper sa
722 2 4812 360 68693 Spray arm 2nd level cpl. saph
723 0 4812 360 68691 Douche ceiling
726 1 4812 530 29331 Tube assembly cpl.saph
726 2 4812 505 18208 Nut
743 1 4812 530 28102 Hose inlet
751 0 4812 418 18338 Water collector
755 0 4812 530 29119 Bend
755 2 4812 530 48148 Tray leak
756 0 4812 360 58479 Floater
761 0 4812 480 58122 Sieve fine
761 2 4812 418 18337 Cover sieve
761 3 4812 418 18341 Cover
761 4 4812 530 58141 O-Ring
763 0 4812 480 58363 Sieve coarse
781 0 4812 530 29113 Hose draining
781 3 4812 281 28417 Flap non-return
783 4 4812 530 28904 Hose 10x3x265+10

SERVICE Whirlpool Europe DWHB80W 21.02.2007 (Mod. 01) / Page 5
Customer Service 8542 400 53000 Doc. No: 4812 728 14196
Spare part list
Model DWH B80 W
Service No. 854240053000
Version 854240053000
Pos. No. 12NC Code Description
783 6 4812 530 28824 Hose 10,3X3X245
791 0 4812 532 68099 Gasket
791 2 4812 530 58093 Gasket
791 4 4812 466 68503 Gasket
791 5 4812 466 68504 Gasket
900 1 4812 310 28351 Fastener set n.sh. (IKEA)
901 0 4812 401 18709 Clamp hose S10-16/9-C7W1
901 1 4812 401 18708 Strap 050,0
901 2 4812 401 18705 Strap 033,1
901 3 4812 401 18806 Strap 47,0 mm
901 5 4812 401 48588 Strap 028,6
901 8 4812 401 18711 Clamp hose 25-29
902 2 4812 404 78241 Holder
910 1 4812 502 18394 Screw 3,5x14-H
910 2 4812 502 18363 Screw 4,0x12-H
910 3 4812 502 18527 Screw 4x15 T20
910 4 4812 502 18741 Screw M3,5x8-T15M
910 5 4812 502 18739 Screw 3,5x8 Tx15
910 7 4812 502 18397 Screw INOX A2 M 5X12
910 8 4812 502 18389 Screw 5x20 T20
910 9 4812 401 18706 Screw 2,5x18-H
964 1 4812 466 68573 Gasket housing upper
993 1 4812 466 78388 Foil protection
993 2 4812 404 48753 Key foot
993 5 4822 532 80216 Funnel salt

SERVICE
05.02.2007 / Page 6 DWH B80 W Whirlpool Europe
Doc. No: 4812 728 14196 8542 400 53000 Customer Service
Exploded view

SERVICE Whirlpool Europe DWH B80 W 05.02.2007 / Page 7
Customer Service 8542 400 53000 Doc. No: 4812 728 14196
Exploded view

SERVICE
05.02.2007 / Page 8 DWH B80 W Whirlpool Europe
Doc. No: 4812 728 14196 8542 400 53000 Customer Service
Circuit diagram
3in1 Multi-tablet Micro switch (3in1)
C1 Capacitor DLB Timerswitch Delay DPM Drain pump motor DD Cleaning agent dosage DR Final rinse dosage DS Door switch FM Flow meter HEW Heating IF Interference filter L Line LS6 Water leakage switch MS Main switch NTC Thermostat temp. sensor N Neutral PRG Plug to program RE2 Relay Heating RE3 Relay Spray pump motor RR SA Reed relay salt RR RA Reed relay rinsaid SPM Sprayarm motor THS1 Safety thermostat THS 2 Fuse TBL Power supply terminal TL Winding protective contact UCB User- and Control board VM Fan ventilator WV1 Water inlet valve WV2 Water regenerating valve WI Water indicator 00 black 66 blue 88 grey 99 white

SERVICE Whirlpool Europe DWH B80 W 05.02.2007 / Page 9
Customer Service 8542 400 53000 Doc. No: 4812 728 14196
Program diagram

SERVICE
05.02.2007 / Page 10 DWH B80 W Whirlpool Europe
Doc. No: 4812 728 14196 8542 400 53000 Customer Service
Text/Legend

SERVICE Whirlpool Europe DWH B80 W 05.02.2007 / Page 11
Customer Service 8542 400 53000 Doc. No: 4812 728 14196
Text/Legend

SERVICE
05.02.2007 / Page 12 DWH B80 W Whirlpool Europe
Doc. No: 4812 728 14196 8542 400 53000 Customer Service
Text/Legend

SERVICE Whirlpool Europe DWH B80 W 05.02.2007 / Page 13
Customer Service 8542 400 53000 Doc. No: 4812 728 14196
Text/Legend

SERVICE
05.02.2007 / Page 14 DWH B80 W Whirlpool Europe
Doc. No: 4812 728 14196 8542 400 53000 Customer Service
Text/Legend

SERVICE Whirlpool Europe DWH B80 W 05.02.2007 / Page 15
Customer Service 8542 400 53000 Doc. No: 4812 728 14196
Text/Legend