Whirlpool GY396LXP User guide

30" Freestanding and Slide-In Electric Range
PRODUCT MODEL NUMBERS OVERALL DIMENSIONS
CABINET OPENING DIMENSIONS
SLIDE-IN RANGE
COUNTERTOP PREPARATION
GY396LXP
GY398LXP
Electrical: When a 4-wire or 3-wire,
single phase 120/240-volt, 60 Hz, AC-only
electrical supply is available, a 50 amp
maximum circuit protection is required (or,
if specified on the model/serial rating
plate, when a 4-wire or 3-wire single
phase 120/208-volt 60 Hz, AC-only
electrical supply is available, a 40 amp
maximum circuit protection is required),
fused on both sides of the line. The
model/serial number rating plate is located
on the oven frame behind the storage
drawer panel. A time-delay fuse or circuit
breaker is recommended.
Because Whirlpool Corporation policy includes a continuous commitment to improve our
products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
The cooktop sides of the slide-in range fit over the
cutout edge of your countertop.
If you have a square finish (flat) countertop and the
opening width is 30" (76.2 cm), no countertop
preparation is required.
Formed front-edged countertops: Must have
molded edge shaved flat 3/8" (1.0 cm) from each
front corner of opening.
Tile countertops may need trim cut back
3/8" (1.0 cm) from each front corner and/or
rounded edge flattened.
If countertop opening width is greater than 30",
adjust the 3/8" (1.0 cm) dimension.
Countertop must be level. Place level on
countertop, first side to side; then front to back. If
countertop is not level, range will not be level. Oven
must be level for satisfactory baking performance.
Slide-in Range
Cabinet opening dimensions shown are for
25” (64 cm) countertop depth, 24” (61 cm)
base cabinet depth and 36” (91.4 cm)
countertop height.
Ref. 9757446
05-20-04
NOTE: 24" (61 cm) min.when bottom of wood or metal
cabinet is protected by not less than 1/4" (0.64 cm)
flame retardant millboard covered with not less than No.
28 MSG sheet steel, 0.015" (0.4 mm) stainless steel,
0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper.
30" (76.2 cm) min. clearance between the top of the
cooking platform and the bottom of an unprotected wood
or metal cabinet.
7 ⁷⁄₈"
(20 cm)
30"
(76.2 cm)
43 ⁷⁄₈"
(111.4 cm)
overall
height
36" (91.4 cm)
cooktop height
with leveling
legs lowered
1¹⁄₂ turns
30"
(76.2 cm)
*27"
(68.6 cm)
to handle
13" (33 cm) max.
upper cabinet depth
For minimum
clearance to
the top of the
cooktop, see
NOTE.
30" (76.2 cm) min.
opening width
30" (76.2 cm) min.
opening width
18" (45.7 cm)
upper cabinet
to countertop
4" (10.2 cm)
min. clearance
from both sides
of range to side
wall or other
combustible
material.
Junction box -
8" (20.3 cm) to
22" (55.9 cm) from
either cabinet,
7" (17.8 cm) max.
from door.
⁷⁄₈" (2.2 cm)
min. required
between cutout
and cabinet
door or hinge.
Junction box -
8" (20.3 cm) to
22" (55.9 cm) from
either cabinet,
7" (17.8 cm) max.
from floor.
22 ³⁄₄" (57.8 cm)
opening depth
30" (76.2 cm)
opening width
For minimum
clearance to
the top of the
cooktop, see
NOTE.
18" (45.7 cm)
upper cabinet to
countertop
13" (33 cm)
upper cabinet depth
30" (76.2 cm)
opening width
⁷⁄₈" (2.2 cm) min.
required between
cutout and cabinet
door or hinge.
4" (10.2 cm) min.
clearance from
both sides of
range to side wall
or other combustible
material between
upper cabinet and
countertop.
¹⁄₄" (6.2 cm)
radius both
corners
23 ¹⁄₂"
(59.8 cm)
30"
(76.2 cm)
30 ¹¹⁄₁₆"
(77.9 cm)
35 ⁵⁄₈"
(90.5 cm)
cooktop height
with leveling
legs lowered
1¹⁄₂ turns
*27"
(68.6 cm)
to handle
Freestanding
Range
22 ³⁄₄"
(57.8 cm)
30"
(76.2 cm)
30 ³⁄₄"
(78.1 cm)
³⁄₈"
(1.0 cm)
* When installed in a 24" (61 cm) base cabinet
with 25" (63.5 cm) countertop; front of oven
door protrudes 1-7/8" (4.8 cm) beyond 24 "
(61 cm) base cabinet.
®