Whirlpool WVIID1058BKG User manual

1
SERVICE MANUAL Automatic Washer
WVIID1058BKG
WVWD1050BKG
WVWD950BKG
WVWD850BKG
SPECIFICATION
Power source
Overall dimension(Net dimension)
Net weight
Power consumption
Motor output
Marked capacity of washing/spinning
Washing method
Water capacity
Pulsator speed
Spinner tub speed
AC 230V, 60Hz
540mmX568mmX955mm
34kg
400W/1500W
140W
10.5kg/9.5kg/8.5kg
Automatic reverse turn
65 Liters
60-190 rpm
700 rpm
Specification: Subject to change without notice.

2
ABNORMALCONDITION
When the washer is abnormal, the washer stops as the every actions turns off, beep tone
sounds ON-0.1 second and OFF-0.1 second for 6 seconds and number window LED display
abnormal code. The washer judges the following six conditions as abnormal condition.
1) Abnormal condition of water supply
In supplying with water, the water level does not reach extra low level within 10 minutes or
does not reach your chosen water level within 20 minutes.
The number window LED display abnormal code: and the electric buzzer sounds to
indicate a problem at the same time.
2) Abnormal condition of drain
In draining, the water level does not go down below the reset level of the water level sensor
within 8 minutes.
The number window LED display abnormal code: and the electric buzzer sounds to
indicate a problem at the same time.
3) Abnormal condition of spin-dry
•The safety switch works 3 times continuously during the program of rinse-spin or works 1
time in the single program of spin-dry.
The number window LED display abnormal code: and the electric buzzer sounds to
indicate a problem at the same time.
•The washer lid is opened.
The number window LED display abnormal code: and the electric buzzer sounds to
indicate a problem at the same time.
4) Abnormal condition of child lock.
Running in setting child lock, the washer lid is opened beyond 4 seconds.
The number window LED display abnormal code: and the electric buzzer sounds to
indicate a problem at the same time.
5) Abnormal condition of water level sensor.
The water level sensor malfunctions or the water level is overrunning the alert level when the
water does not stop.
The number window LED display abnormal code: and the electric buzzer sounds to
indicate a problem at the same time.
6) Computer board failure
The digital tube displays the fault code " ", accompanied by a whistle sound.
•Chip data abnormal
7) Abnormal failure of main control and frequency conversion communication

3
The digital tube displays the fault code "Ed2", accompanied by a whistle sound.
•First check whether the reactor is in good contact
•Replace the computer main control board
8) The display board cannot receive the main control signal.
The digital tube displays the fault code " " or "Ed1"。
•First check whether the connection between the main control board and the display board is
good。
•Replace the display board to test whether the function is normal。
9) High current fault
The digital tube displays the fault code " ", accompanied by a whistle sound
• First determine if there is too much foam
• Then check whether the inner barrel is operating normally
• Check whether the computer board functions normally.
10)Over-voltage fault
The digital tube displays the fault code " ", accompanied by a whistle sound
• First detect whether the user's home voltage is too high
• Check whether the computer board function is normal
11)Low voltage fault
The digital tube displays the fault code " ", accompanied by a whistle sound
• First check whether the user's home voltage is too low
• Check whether the computer board function is normal
12) Abnormal motor operation failure
The digital tube displays the fault code " ", accompanied by a whistle sound
• Check whether the motor wiring harness is good
• Check whether the computer main control board function is normal
13)Excessive leakage current detection fault
The digital tube displays the fault code " ", accompanied by a whistle sound。
• Replace the computer main control board
14)IPM hardware abnormal failure
The digital tube displays the fault code " ", accompanied by a whistle sound
• Replace the computer main control board

15) Water temperature sensor failure EC2
The digital tube displays the fault code "EC2"
• First check whether the connection between the main control board and the water temperature
sensor is good
• Replace the heating tube or the computer main control board to test whether the function is
normal
16)Heating pipe failure E6C or E7C
The digital tube displays the fault code "E6C" or "E7C"
• First check whether the connection between the main control board and the heating tube is
good，Measure whether the heating tube resistance is in the normal range
• Replace the heating tube to test whether the function is normal
17) Door lock failure U4
The digital tube displays the fault code "U4"
• First check whether the connection between the main control board and the door lock is good
Is the door sensor in the normal position
• Replace the door lock to test whether the function is normal
18)High temperature alarm H
Digital tube display code "H"
• The temperature in the barrel is too high and the lid cannot be opened for safety，please wait
patiently。

5
CIRCUIT DIAGRAM
WVIID1058BKG
WVWD1050&950&850BKG
THOUBLESHOOTING
a. Power Source
Yes
No
COLOR SYMBOL
Gr
Bl
G
B
LB
Br
O
P
R
W
Y
V
GRAY
BLUE
GREEN
BLACK
LIGHT BLUE
BROWN
ORANGE
PINK
RED
WHITE
YELLOW
VIOLET
TROUBLE
INSPECTION
CAUSES
REMEDY
Any indications
and beep do not
work when
power switch is
on and the start
button is pressed
INSPECTION
Is fuse blown?
Deterioration of fuse.
Motor is defective.
Capacitor is defective.
Replace.
Replace.
Replace.
Poor connect of
connectors
Control circuit board is
defective
Repair or replace.
Replace.

6
Hose joint assembly
Cushion
Filter
Does water stop
when the plug
is removed or
power switch is
OFF?
b. Water Supply
Yes
No
Low
High
Note: When removing the flow sheet, reinstate the filter in place correctly.
Yes
No
TROUBLE
INSPECTION
CAUSES
REMEDY
INSPECTION
Water does not
flow when the
power switch is
on and start
button is pressed.
Does humming
noise come on
from water
valve？
Something on the filter of
the water valve or hose
joint assembly.
Clean the filter.
Poor connect of
connectors.
Water valve is defective.
Water level sensor is
defective.
Control circuit board is
defective.
Repair or replace.
Replace.
Replace.
Replace.
Water is not
supplied normally.
Check water
pressure.
Remove the flow
sheet of the water
valve.
Replace the water
valve.
Clean the filter on
the water valve or
hose joint
assembly.
Replace the water
valve.
Water does not stop
Something in the air trap
hose or air leaks from a
part related water level
sensor system.
Water level sensor is
defective.
Control circuit board is
defective.
Something on the
diaphragm on the water
valve.
Diaphragm is deformed
Clean or replace.
Replace .
Replace.
Replace or
disassemble the
valve and clean
the diaphragm
Replace
Replace .
Replace
The height of drain hose is
less than 0.7m.
Make the height of
drain hose is not less
than 0.7m.

7
Bearing ass’y is defective.
Replace.
Motor wires are
dis-connected.
Capacitor wires are
dis-connected.
Capacitor is defective.
Motor coil shorten.
Brake lining on bearing ass’y
is worn out.
Brake lever ass’y is defective.
Torque motor is broken.
Brake lining is worn out.
Brake lever ass’y is defective.
Foreign matter in drain hose.
Valve bellow is deformed.
Pump lead wire is
disconnected.
Control circuit board is
defective.
c. Wash/Rinse
No
Yes
No
Yes
No
Yes
Yes
No
No
d. Drain
Yes
No
TROUBLE
INSPECTION
CAUSES
REMEDY
Washing cycle does
not start even if
water keeps the
selected water level.
INSPECTION
Does the spin tub
rotated normally
when the
COURSE button
is set to SPIN?
Bearing ass’y is defective.
Poor connect of
connectors
Thermostat on motor is
opened.
Control circuit board is
defective.
Replace.
Replace.
Repair or replace
after cooling down.
Replace.
Does the pulsator
rotate by hand?
Does humming
noise come on
from motor?
Replace or repair.
Replace or repair.
Replace.
Replace.
The spin tub rotates
together with the
pulsator during
washing or rinsing
cycle.
Is the torque motor
working normally?
Replace bearing ass’y.
Replace bearing ass’y.
Replace.
Note:
Brake-work is
normal when spin
tub stops within 10
sec. under no-load.
Does brake-work
normally?
Replace bearing ass’y.
Replace bearing ass’y.
Water does not
drain out.
Is the built-in
pump working
normally？
Clean drain hose
inside.
Repair or replace.
Replace.

8
e. Spin Drying
Yes
No
TROUBLE
INSPECTION
CAUSES
REMEDY
INSPECTION
Drain takes time too
long.
Drain hose ass’y is deformed.
Hose is connected in the
wrong way.
Hose is too long or position of
hose is too high.
Repair or replace.
Repair.
Repair.
Note: In draining, the water lever sensor can
not reset in 8minutes.
The number window LED display
abnormal code: and begin blinking
on and off at the same time and the
electric buzzer sounds to indicate a
problem.
Note: In draining, the water level sensor can
not reset in 8 minutes.
The number window LED display
abnormal code: and begin blinking
on and off at the same time and the
electric buzzer sounds to indicate a
problem.
Spin drying cycle
does not work.
INSPECTION
Does safety
device work?
Machine inclines.
Replace with level.
The V-belt is slipping.
The V-belt is snapped.
Small pulley mounting
screw is loosed.
Motor is disconnected or
burnt.
Capacitor is broken or
disconnected.
Bearing ass’y is defective.
Torque motor is defective.
Brake lever is defective.
Thermostat on motor is
opened.
Poor contact of
connectors.
Control circuit board is
defective.
Adjust the motor
position.
Replace.
Tighten up.
Replace.
Replace.
Replace.
Replace.
Repair or replace.
Repair or replace
after cooling down.
Repair or replace.
Replace.
Note:
1. The safety switch works 3 times
continuously or works 1 time in the
single program of spin-dry.The
number window LED display abnormal
code: and begin blinking on and off
at the same time and the electric buzzer
sounds to indicate a problem.
2. Do not disconnect the wire from the
capacitor, because this wire acts as
de-pressing noise from outside to the
micro-computer.

9
Operation of safety device
When the safety device works by abnormal swing of spin drum, machine works automatically to
stop Spin-Dry cycle and operates water supply valve to pour water into the Wash/Spin Tub and
then starts washing cycle for replacing washing clothes evenly.
After above operation has down twice, if safety device works again, machine will stop, and the
number window LED display abnormal code: and begin blinking on and off at the same time
and the electric buzzer sounds to indicate a problem.
•Open the Wash Lid and rearrange the clothes evenly around the Wash/Spin Tub.
•Close the Wash Lid and press the START/PAUSE button again.
f. Buzzing and rattling
Low
High
TROUBLE
INSPECTION
CAUSES
REMEDY
INSPECTIONINSPECTION
Start of spin-drying.
Normal spin.
Safety device work.
Electric circuit
counts operation
of safety device.
Electric circuit works to stop
spin when safety device
detects continuously three
times of abnormal swing of
spin drum.
Automatic
adjustment or
load.
Buzzing/rattling
during water
supply.
INSPECTION
Something in water valve.
Replace.
INSPECTION
Is high water
pressure (more
than 4kg/cm2)?
Faucet open too far
Adjust faucet
turning.
Stop of Spin-Dry
Agitation of load (Rinsing
for 2 minutes).
Water supply

10
Yes
No
TROUBLE
INSPECTION
CAUSES
REMEDY
INSPECTION
Buzzing/rattling
during washing
or rinsing.
Does some noise
sound during
spin drying?
Belt is slipping.
Pulley is loose.
Some part touch motor
Adjust.
Tighten.
Repair or replace
Something underneath
pulsator.
Pulsator is rubbing.
Pulsator shaft is burnt.
Remove.
Adjust bearing ass’y.
Replace bearing ass’y.
Buzzing/rattling
during spin-dry.
Is sound in
low-pitched
monotone?
Bearings of bearing ass’y
is defective.
Replace.
Is variable sound
happened by
vibration?
Does noise sound
when the washer
begins to work?
Is clattering on
maximum
rotation?
Is flapping?
Machine is in unbalance.
Suspension rod ass’y is
worn out.
Belt is slipping
Motor pulley is loose.
Wire and/or air trap hose
is loose.
Place machine
evenly on base.
Replace.
Adjust.
Tighten up.
Tighten.