Whispbar K460W User manual

K460W
Fitting Kit
EN Fitting Instructions for Basic Carrier
DMontageanleitung für Basisträgersystem
ES Instrucciones de montaje para el sistema
de transporte
FInstructions de montage pour Basic Carrier
NO Monteringsanvisning for takstativ
PT Instruções de Montagem para sistema de
transporte.
RU Установочные Инструкции для
Поперечных Балок
x 1 x 1 x 8 x 4
x 4 x 4 x 1 x 1
x 1 x 1 x 4 x 4
Revision No: 10J 1

Fitting Kit K460W
MAX kgs (lbs)
W/P WHD
Toyota
Avensis, 5dr Estate 09-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs)
Avensis, 5dr Wagon Apr 09-+ NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
2

Fitting Kit K460W
X
A B C 1 2 3
Avensis, 5dr Estate 09-+ (EU) -40mm 680mm - 830mm 800mm -
-1 -9/16ths" 26 3/4ths" - 32 11/16ths" 31 1/2ths" -
Avensis, 5dr Wagon Apr 09-+ (NZ) -40mm 680mm - 830mm 800mm -
-1 -9/16ths" 26 3/4ths" - 32 11/16ths" 31 1/2ths" -
3

Fitting Kit EN
K460W
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●Use keys to remove covers.
4

Fitting Kit EN
K460W
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
●Adjust crossbar in or out to suit vehicle.
Refer to the crossbar instructions for
crossbar adjustment.
●Attaches to factory-fitted mounting points
●Please check the front of this manual for
information relating specifically to your
vehicle.
5

Fitting Kit EN
K460W
●Tighten adjusting screw to 2 Nm (1.5 ft lb)
hand tight.
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●Remove both pins from each leg. Use
tapered end of spanner located inside left
hand cover to assist.
6

Fitting Kit EN
K460W
●Detach foot from leg. Store loose parts in a
safe place.
●Repeat for all legs.
●Assemble metal loadplate and rubber pad
from the fitting kit.
●Repeat for all four items.
●Assemble metal loadplate into leg. Ensure
loadplate interlocks with the leg.
7

Fitting Kit EN
K460W
●Using short capscrew and washer, secure
assembly onto leg (use Hex Screwdriver
supplied with crossbar to assist)
●Repeat for all legs.
Fitment
●Open or remove fixed-point covers.
●Store items away in a safe place.
●Install adaptor onto vehicle.
●Repeat for all four positions.
8

Fitting Kit EN
K460W
●Cover plate location
A = 605A
B = 606A
C = 607A
D = 608A
●Fit cover plates over opening.
●Hole in cover should line up with adaptor.
●Place crossbar foot over coverplate
●Fit the M6 socket head screw and M6
washer.
●Leave loose until both sides have had the
screw fitted.
9

Fitting Kit EN
K460W
●Tighten foot and cover plate down using
the Hex Key.
●Ensure that the cover plate and foot sit
firmly on the roof.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
10