White Rodgers 775 User manual

Installation Instructions for
Heating & Air Conditioning
MODEL 775
7 Day ProgrammableThermostat
CONTENTS
Preparations.................................................. 1
Thermostat Details ........................................ 1
Removing Old Thermostat ............................ 1
Mounting and Wiring ..................................... 2
Check Thermostat Operation ........................ 3
Programming your Thermostat ..................... 4
Specifications ................................................ 6
Troubleshooting ............................................ 6
PREPARATIONS
THERMOSTAT DETAILS REMOVING OLDTHERMOSTAT
Before removing wires from old thermostat’s switching subbase,
labeleachwirewiththeterminaldesignationitwasremovedfrom.
1. Remove Old Thermostat: A standard heat/cool thermostat
consists of three basic parts:
a. The cover, which may be either a snap-on or hinge type.
b. Thebase,whichisremovedbylooseningallcaptivescrews.
c. The switching subbase, which is removed by unscrewing
themountingscrewsthatholditonthewalloradaptorplate.
2. Shut off electricity at the main fuse box until installation is
complete. Ensure that electrical power is disconnected.
3. Removethefrontcover oftheoldthermostat.With wiresstill
attached,removewallplatefromthewall.Iftheoldthermostat
hasawallmountingplate,removethethermostatandthewall
mounting plate as an assembly.
4. Identifyeachwireattached to the old thermostat usingthe
labels enclosed with the new thermostat.
5. Disconnectthewiresfromtheoldthermostatoneatatime.DO
NOT LET WIRES FALL BACK INTO THE WALL.
6. Install new thermostat using the following procedures.
To prevent electrical shock and/or equipment damage,
disconnect electrical power to the system at the main
fuse or circuit breaker until installation is complete.
CAUTION
!
Printed in U.S.A. PART NO. 37-6384A
0212
WHITE-RODGERS
EMERSON ELECTRIC CO.
9797 REAVIS ROAD
ST. LOUIS, MISSOURI 63123-5398
www.white-rodgers.com
Failure to follow and read all instructions carefully
before installing or operating this control could cause
personal injury and/or property damage
Assemble tools required as shown below.
YOURTHERMOSTAT REPLACES
1
23
WIRE CUTTER/STRIPPER
Typical System Compatibility Chart 620
Standard Heat Only Two Wire Gas or Oil Fired Systems (24 volt) Yes
Electronic Ignition Heat Only Two Wire Systems (24 volt) Yes
Electronic Ignition Heat Only Gas or Oil Fired Systems (24 volt) Yes
Standard Heat/Cool Systems (24 volt) Yes
Heat/Cool Systems Electric Heat (24 volt) Yes
Heat Only Electric Heat Systems (24 volt) Yes
Cool Only Systems (24 volt) Yes
Heat Pump Systems (No Aux or Emergency Heat) Yes
Hot Water Zone Heat Only (Two Wire) Systems Yes
Hot Water Zone Heat Only (Three Wire) Systems No
Line Voltage Heating or Baseboard 110/240 Volt Systems No
Millivolt Systems Floor or Wall Furnaces Yes
12 VDC Mobile Home Application Yes
Multistage Systems No
Systems Exceding 30VAC, 1.5 Amp No
WRH BRC
GOY
+-+-
GAS
ELEC
W904
W905
Figure 1. Thermostat base
Mounting
hole
Mounting
hole
W905
Clip for
Hydronic
System
W904
Clip for
Celsius Display
Electric/Gas
Switch
HAND OR POWER
DRILL WITH 3/16 INCH
DRILL BIT, IF NEEDED
FLAT BLADE SCREWDRIVER
SPIRIT LEVEL OR PLUMB BOB AND LINE OPTIONAL—
THERMOSTAT DOES NOT NEED TO BE LEVEL TO WORK PROPERLY

MOUNTING ANDWIRING
Take care when securing and routing wires so they do
not short to adjacent terminals or rear of thermostat.
Personal injury and/or property damage may occur.
CAUTION
!
ATTENTION! This product does not contain mercury. How-
ever, this product may replace a unit which contains mercury.
Do not open mercury cells. If a cell becomes damaged, do not
touch any spilled mercury. Wearing non-absorbent gloves, take
up the spilled mercury and place into a container which can be
sealed.Ifa cellbecomes damaged, theunit shouldbediscarded.
Mercurymustnotbediscardedinhouseholdtrash.Whentheunit
this product is replacing is to be discarded, place in a suitable
container and return to White-Rodgers at 9797 Reavis Road, St.
Louis, MO, 63123-5398 for proper disposal.
REMOVING OLDTHERMOSTAT
CONTINUED FROM FIRST PAGE
WARNING
!
Do not use on circuits exceeding specified voltage.
Higher voltage will damage control and could cause
shock or fire hazard.
Do not short out terminals on gas valve or primary
control to test. Short or incorrect wiring will damage
thermostat and could cause personal injury and/or
property damage.
Thermostat installation and all components of the sys-
tem shall conform to Class II circuits per the NEC code.
TERMINAL CROSS REFERENCE CHART
New Thermostat
Terminal Designation Other Manufacturers’ Terminal Designation
RH
RC
G
W
Y
4
R
G
W
Y
RH
R
G
W
Y
M
V
F
H
C
R5
-
G
4
Y6
R
-
G
W
Y
**
* These are four-wire, single-transformer systems.
Factory installed jumper wire between the RH
and RC terminals must remain in place.
www.white-rodgers.com
4
3
Electric Heat or Single-Stage
Heat Pump Systems
This thermostat is configured from the factory to operate a heat/
cool, fossil fuel (gas, oil, etc.), forced air system. It is configured
correctly for any system that DOES NOT require the thermostat
to energize the fan on a call for heat. If your system is an electric
or heat-pump system that REQUIRES the thermostat to turn on
the fan on a call for heat, locate the GAS/ELECTRIC switch (see
fig. 1) and switch it to the ELECTRIC position. This will allow the
thermostattoenergizethefanimmediatelyonacallforheat.Ifyou
are unsure if the heating/cooling system requires the thermostat
to control the fan, contact a qualified heating and air conditioning
service person.
Hydronic (Hot Water or Steam)
Heating Systems
Thisthermostatissettooperateproperlywithaforced-airheating
system. If you have a hydronic heating system (a system that
heats with hot water or steam), you must set the thermostat to
operate properly with your system by changing the first option in
the configuration menu to SL (see Configuration Menu, page 5).
Attach Thermostat Base to Wall
1. Removethepackingmaterial fromthethermostat.Gentlypull
the cover straight off the base. Forcing or prying on the
thermostat will cause damage to the unit. If necessary, move
the electric heat switch (see ELECTRIC HEAT SYSTEMS,
above).
2. Connectwires beneathterminalscrews onbase usingappro-
priate wiring schematic (see figs. 2 through 7).
3. Placebaseoverholeinwallandmarkmountingholelocations
on wall using base as a template.
4. Move base out of the way. Drill mounting holes.
5. Fasten base loosely to wall, as shown in fig. 1, using two
mountingscrews.Placealevelagainstbottomofbase,adjust
until level, and then tighten screws. (Leveling is for appear-
ance only and will not affect thermostat operation.) If you are
using existing mounting holes, or if holes drilled are too large
anddo notallow you totighten basesnugly, useplastic screw
anchors to secure subbase.
6. Push excess wire into wall and plug hole with a fire-resistant
material (such as fiberglass insulation) to prevent drafts from
affecting thermostat operation.
Battery Location
This thermostat requires 2 “AAA” alkaline batteries to operate. If
the word low “LO BATT” is displayed, the batteries are low and
shouldbereplacedwithfresh“AAA”Energizer®alkalinebatteries.
To replace the batteries, install the batteries along the top of the
base (see fig. 1). The batteries must be installed with the posi-
tive (+) ends to the right.

CHECKTHERMOSTAT OPERATION
www.white-rodgers.com
5
RH
24 VAC 120 VAC
Hot
Neutral
THERMOSTAT
SYSTEM
G W
Figure 2. Typical wiring diagram for
heat only, 3-wire, single transformer systems
TRANSFORMER
Heating
System
Fan
Relay
YRC
JUMPER
WIRE
OB
For 2-wire Heat only,
attach to RH and W
NOTE
RH
Y
24 VAC 120 VAC
Hot
Neutral
TRANSFORMER
THERMOSTAT
SYSTEM
G W
Figure 3. Typical wiring diagram for
cool only, 3-wire, single transformer systems
Cooling
System Fan Relay
RCOB
JUMPER
WIRE
RH
Y
24 VAC 120 VAC
Hot
Neutral
THERMOSTAT
SYSTEM
G W
Figure 4. Typical wiring diagram for
heat/cool, 4-wire, single transformer systems
TRANSFORMER
Heating
System
Fan
Relay
Cooling
System
RC
JUMPER
WIRE
OB
RED jumper wire (provided with thermostat) must be
connected between thermostat RH and RC terminals
for proper thermostat operation with this system.
NOTE
RH
Y
24 VAC 120 VAC
Hot
Neutral
THERMOSTAT
SYSTEM
G W
Figure 5. Typical wiring diagram for
heat/cool, 5-wire, two-transformer systems
HEATING
TRANSFORMER
Heating
System
Fan
Relay
Cooling
System
RC
24 VAC 120 VAC
Hot
Neutral
COOLING TRANSFORMER
OB
RH
Y
24 VAC 120 VAC
Hot
Neutral
THERMOSTAT
SYSTEM
G W
Figure 6. Typical wiring diagram for heat pump
with reversing valve energized in COOL
TRANSFORMER
Reversing
Valve*
RCOB
JUMPER
WIRE
Compressor
Contactor
JUMPER
WIRE
* Reversing valve is energized when the
system switch is in the COOL position
Fan
Relay
RH
Y
24 VAC 120 VAC
Hot
Neutral
THERMOSTAT
SYSTEM
G W
Figure 7. Typical wiring diagram for heat pump
with reversing valve energized in HEAT
TRANSFORMER
Reversing
Valve*
RCOB
JUMPER
WIRE
Compressor
Contactor
JUMPER
WIRE
* Reversing valve is energized when the
system switch is in the HEAT position
Fan
Relay
NOTE
To prevent static discharge problems, touch side of ther-
mostattoreleasestaticbuild-upbeforetouchinganykeys.
If at any time during testing your system does not operate
properly, contact a qualified serviceperson.
Fan Operation
If your system does not have a Gterminal connection, skip to
Heating System.
1. Turn on power to the system.
2. Move fan switch to ON position. The blower should begin to
operate.
3. Move fan switch to AUTO position. The blower should stop
immediately.
Thisthermostat has a timedelay between coolingcycles to allow
the head pressure in the compressor to stabilize. If the tempera-
tureisadjustedtocallforcoolwithin5minutesofthelastcyclethe
snowflake icon will blink indicating the thermostat is locked out.
After 3 to 5 minutes, the compressor will start and the snowflake
icon will stop flashing. This helps prevent the compressor from
cycling too quickly and is normal operation for the thermostat.
1. Move SYSTEM switch to COOL position.
2. Press toadjustthermostat settingbelowroom tempera-
ture. The blower should come on immediately on high speed,
followed by cold air circulation
3. Press to adjust temperature setting above room tem-
perature. The cooling system should stop operating.
Heating System
1. MoveSYSTEMswitch toHEAT position.Iftheheatingsystem
has a standing pilot, be sure to light it.
2. Press toadjustthermostat setting aboveroom tempera-
ture. The heating system should begin to operate.
3. Press to adjust temperature setting below room tem-
perature. The heating system should stop operating.
To prevent compressor and/or property damage, if the
outdoortemperatureisbelow50°F,DONOToperatethe
cooling system.
CAUTION
!
Cooling System
MOUNTING ANDWIRING
CONTINUED FROM SECOND PAGE
4

CHECKTHERMOSTAT OPERATION
CONTINUED FROM THIRD PAGE
www.white-rodgers.com
Before you begin programming your thermostat, you should be
familiarwith its features and withthe displayand the locationand
operation of the thermostat buttons. Your thermostat consists of
two parts: the thermostat cover and the base. To remove the
cover, gently pull it straight out from the base. To replace the
cover, line up the cover with the base and press gently until the
cover snaps onto the base.
The Thermostat Buttons and Switches
1
(Up arrow) Raises temperature setting.
2
(Down arrow) Lowers temperature setting.
3
TIME button.
4
PRGM (program) button.
5
RUN (program) button.
6
HOLD button.
7
FAN switch (ON, AUTO).
8
SYSTEM switch (COOL, OFF, HEAT).
THE DISPLAY
9
Indicates day of the week.
10
is displayed when the SYSTEM switch is in the HEAT
position. is displayed (non-flashing) when the SYSTEM
switch is in the COOL position. is displayed (flashing)
when the compressor is in lockout mode.
11
Alternately displays current time and temperature.
12
“LO BATT” is displayed when the 2 “AAA” batteries are low
and should be replaced. Nothing else will be displayed.
13
Displayscurrentlyprogrammedsettemperature(thisisblank
when SYSTEM switch is in the OFF position).
14
The word HOLD is displayed when the thermostat is in the
HOLD mode.
OPERATING FEATURES
Nowthatyouarefamiliarwiththethermostatbuttonsanddisplay,
readthefollowinginformation tolearnaboutthemany featuresof
the thermostat.
•SIMULTANEOUSHEATING/COOLINGPROGRAMSTOR-
AGE—Whenprogramming, youcanenter both yourheating
and cooling programs at the same time. There is no need to
reprogram the thermostat at the beginning of each season.
•TEMPERATURE OVERRIDE—Press or until the
displayshowsthetemperatureyouwant.Thethermostatwill
override current programming and keep the room tempera-
tureattheselectedtemperatureuntilthenextprogramperiod
begins. Then the thermostat will automatically revert to the
program.
WHITE-RODGERS
TIMEPRGMRUN HOLDFANSYSTEM
OFFONAUTOCOOLHEAT
1
8
9
11
1012
76543
2
13
Figure 8. Thermostat display, buttons, and switches
14
5
•HOLDTEMPERATURE—Thethermostatcanholdanytem-
perature within its range for an indefinate period, without
reverting to the programmed temperature. Press HOLD
button. HOLD will be displayed. Then choose the desired
hold temperature by pressing or . The thermostat
will hold the room temperature at the selected setting until
you press RUN button to start program operation again.
•LOWBATTERYINDICATOR—Ifthe2“AAA”alkalinebatter-
ies are low and should be replaced, the display will be blank
except for “LO BATT”. When the batteries are low, pressing
any button will cause the display to operate for ten seconds.
After ten seconds, the display will be blank except for “LO
BATT”. You cannot program with low batteries, but you can
overridesetpointtemperature.When“LOBATT”occurs,the
thermostatwillraise thetemperature10 degreesaboveyour
setpoint on “COOL” mode and will drop temperature 10
degrees below your setpoint on “HEAT” mode.
•SIMPLIFIED COPY DAY FUNCTION—This feature allows
Monday’s program to be copied into the rest of the week’s
programming. This feature is only available the first time
you program your thermostat. To use this feature, simply
enter the program for Monday as described in PROGRAM-
MINGYOURTHERMOSTAT,andthenpressRUN,orHOLD.

www.white-rodgers.com
CONFIGURATION MENU
6
The configuration menu allows you to set certain thermostat
operating characteristics to your system or personal require-
ments.
Press RUN to make sure the thermostat is in the run program
mode, then press PRGM and RUN at the same time to enter the
configuration menu. The display will show the first item in the
configuration menu.
The configuration menu table summarizes the configuration op-
tions. An explanation of each option follows.
PressHOLDtochangetothenextmenuitemorpressTIMEtogo
backwardstothepreviousiteminthemenu.Toexitthemenuand
return to the program operation, press RUN. If no keys are
pressedwithinfifteenminutes,thethermostatwillreverttonormal
operation.
1) Select FA or SL (Fast or Slow) Heating Cycle Rate—The
FA setting is frequently used for gas, oil or electric heat. The
SLsetting producesalonger heatingcycle whichisnormally
for hot water or steam (hydronic) systems. Both settings
produceveryaccuratetemperature controlandcanbe setto
your personal preference. FA cycles the system just under
1°F and the SL setting cycles at approximately 1.5F°.
2) Select backlit display—The display backlight improves
displaycontrastinlowlightingconditions.Selectingbacklight
ON will keep the light on for a short period of time after any
key is pressed. Selecting OFF will keep the light off.
3) Select Energy Management Recovery OFF or ON—
Energy Management Recovery (EMR) causes the thermo-
stat to start heating or cooling early to make the building
Theonlyway torestorethis featureisto completeasoftware
reset (see reset operation under “TROUBLESHOOTING”
section).
•COPY DAY FUNCTION—This feature allows a selected
day’s program to be copied to the desired days’ program-
ming.TousethisfeatureinviewPRGMmode,selecttheday
to be copied from by pressing HOLD key. Enter the program
fortheselecteddayasdescribedinPROGRAMMINGYOUR
THERMOSTAT.Toenterthecopymode,presstheTIMEkey
for greater than 4 seconds. The LCD should display COPY,
the selected day of the week and the day (flashing) to be
copiedto.Press theHOLD key toselect thedayto becopied
to. Press TIME to execute copy day operation and return to
view program mode. Press RUN key to exit.
Press or to select:
SL
OFF
OFF
ON
4 LO to 4 HI
C
Configuration Menu
* Press HOLD to advance to next item or TIME to move backwards to previous item
Step
1
2
3
4
5
6
7
Press Button(s)
PRGM and RUN
HOLD*
HOLD*
HOLD*
HOLD*
HOLD*
RUN
Displayed (Factory Default)
(FA)
d-L (ON)
E (ON)
LOC (OFF)
0 HI (0)
(F)
Comments
Select FA or SL (Fast or Slow) heating cycle rate
Select display backlight OFF or ON
Select Energy Management Recovery OFF or ON
Select compressor lockout OFF or ON
Select temperature display adjustment higher or lower
Select temperature display to F or C
Returns to normal operation
temperature reach the program setpoint at the time you
specify. Heating will start 5 minutes early for every 1°of
temperature required to reach setpoint.
Example: You select EMR and have your heating pro-
grammed to 65°at night and 70°at 7 AM. If the building
temperature is 65°the difference between 65°and 70°is 5°.
Allowing 5 minutes per degree the thermostat setpoint will
change to 70°at 6:35 AM. Cooling allows more time per
degree because it takes longer to reach temperature.
4) Select Compressor Lockout LOC OFF or ON—Selecting
LOC ON will cause the thermostat to wait 5 minutes before
turning on the compressor if the heating and cooling system
loses power. It will also wait 5 minutes minimum between
cooling cycles. This is intended to help protect the compres-
sor from short cycling. Some newer compressors already
haveatimedelaybuiltinanddonotrequirethisfeature.Your
compressormanufacturercantellyouifthefeatureisalready
present in their system. When the compressor time delay
occurs it will flash the for about five minutes then turn on
the compressor.
5) Select Temperature Display Adjustment 4 LO to 4 HI—
Allows you to adjust the room temperature display 4°higher
or lower. Your thermostat was accurately calibrated at the
factory but you have the option to change the display tem-
perature to match your previous thermostat.
6) Select F°or C°Readout—Changes the display readout to
Centigrade or Fahrenheit as required.
PROGRAMMINGYOURTHERMOSTAT
Thissection will helpyou planyourthermostat’s programto meet
your needs. For maximum comfort and efficiency, keep the
following guidelines in mind when planning your program.
• When heating (cooling) your building, program the tempera-
tures to be cooler (warmer) when the building is vacant or
during periods of low activity.
• During early morning hours, the need for cooling is usually
minimal.
Lookatthefactorypreprogrammedtimesandtemperaturesshown
below. If this program will suit your needs, simply press the RUN
button to begin running the factory preset program.
If you want to change the preprogrammed times and tempera-
tures, follow these steps.
Determine the time periods and temperatures for each day
programs.You must programfour periods foreach day program.
7

www.white-rodgers.com
PERIOD 1
Time Temp Time Temp
Heating/Cooling Schedule Plan
Mon
Tues
Wed
Thur
Fri
Sat
Sun
HEAT COOL
PERIOD 2
Time Temp Time Temp
HEAT COOL
PERIOD 3
Time Temp Time Temp
HEAT COOL
PERIOD 4
Time Temp Time Temp
HEAT COOL
PROGRAMMINGYOURTHERMOSTAT
CONTINUED FROM FIFTH PAGE
However, you may use the same heating and cooling tempera-
tures for consecutive time periods. You can choose start times,
heating temperatures, and cooling temperatures independently
foreachdayprograms(forexample,youmayselect5:00AMand
70°as the 1st period heating start time and temperature on
Monday, then select 7:00 AM and 76°as the 1st period cooling
start time and temperature on Monday). Use the table at the
bottom of the page to plan your program time periods and the
temperaturesyouwantduring eachperiod.Youmayalso wantto
look at the sample program table to get an idea of how the
thermostat can be programmed.
Entering Your Program
Followthesestepstoentertheheatingandcoolingprogramsyou
have selected.
Set Current Time and Day
1. Press TIME button once. The display will show the hour only.
EXAMPLE:
PM
2. Press and hold either or until you reach the correct
hour and AM/PM designation (AM begins at midnight; PM
begins at noon).
3. PressTIMEonce.Thedisplaywindowwillshowtheminutesonly.
EXAMPLE:
4. Press and hold either or until you reach the correct
minutes.
5. Press TIME once. The display will show the day of the week.
6. Press or untilyoureachthecurrentdayoftheweek.
7. Press RUN once. The display will show the correct time and
room temperature alternately.
Enter Heating/Cooling Times and Heating
Temperatures
1. Move the SYSTEM switch to HEAT.
2. Press PRGM once. MO,the abbreviation for Monday, will be
displayed. Also displayed are the currently programmed start
time for the 1st heating period and the currently programmed
temperature fo rthe 1st heating period (flashing).
EXAMPLE:
AM
MO TU WE TH FR
This example shows that for the 1st Monday heating period,
thestarttimeis6:00AM,and70°istheprogrammedtempera-
ture (this example reflects factory preprogramming).
3. If the temperature displayed in not the temperature you want
for Monday”s period 1, press or until the correct
temperature is displayed.
4. To change the displayed start time to the time you have
selectedforMonday’sheatingperiod1,press TIMEonce(the
programmed time will flash). Press or until your
selected time is displayed. The time will change in 15 minute
increments.
5. PressPRGM once.The currentlyprogrammedstart timeand
heating setpoint temperature for Monday’s heating period 2
will be displayed.
6. Repeat steps 3 and 4 to select the start time and heating
temperature for Monday’s 2nd heating period.
7. Repeat steps 3 through 5 for Monday’s 3rd and 4th heating
period. Monday’s heating program is now complete.
7
1ST
2ND
3RD
4TH
1ST
2ND
3RD
4TH
SAMPLE
Heating/Cooling Schedule Plan (Factory Program)
6:00 AM
8:00 AM
5:00 PM
10:00 PM
6:00 AM
8:00 AM
5:00 PM
10:00 PM
70 F
62 F
70 F
62 F
78 F
85 F
78 F
82 F
ALL DAYS OF THE WEEK
Start Time Temperature
Period
COOL HEAT

www.white-rodgers.com
Ifyou areprogramming your thermostatfor thefirst time,and you
want programming for all days of the week to be the same as
Monday’s program, press RUN or HOLD at this point, and
proceed to the SELECT COOLING TEMPERATURES section
(this simplified COPY DAY feature only works the first time you
programyourthermostat;referto“COPYDAYFUNCTION”ifyou
want to copy one day’s programming to a specific day program-
ming; if you are changing your thermostat’s programming, you
must program each day separately.
8. Press HOLD once. “TU” (indicating Tuesday’s program) will
be displayed, along with the start time for the 1st heating
period and the currently programmed heating setpoint tem-
perature.
9. Repeat steps 3 through 7 to complete Tuesday’s heating
program.
10.Continue entering each day’s programming until all heating
periods temperatures have been selected.
11.Press RUN to end heating programming. Proceed to the
SELECT COOLING TEMPERATURES section.
Enter Cooling Temperatures
If the outside temperature is below 50°F, disconnect power
to the cooling system before programming. Energizing the
air conditioner compressor during cold weather may cause
personal injury or property damage.
1. Move SYSTEM switch to COOL position.
2. Follow the procedure for entering your heating program, using
your selected cooling times and temperature.
Check your programming
Follow these steps to check your thermostat programming one
final time before beginning thermostat operation.
Symptom Possible Cause Corrective Action
No Heat/No Cool/No Fan 1. Blown fuse or tripped circuit breaker. Replace fuse or reset breaker.
(common problems) 2. Furnace power switch to OFF. Turn switch to ON.
3. Furnace blower compartment door or Replace door panel in proper position to engage
panel loose or not properly installed. safety interlock or door switch.
No Heat 1. Pilot light not lit. Re-light pilot.
2. System Switch not set to Heat. Set System Switch to Heat and raise temp above
room temp.
3. Loose connection to thermostat or system. Verify thermostat and system wires are securely
attached.
4. Furnace Lock-Out Condition. Heat may also Many furnaces have safety devices that shut
be intermittent. down when a lock-out condition occurs. If the
heat works intermittently contact the furnace
manufacturer or local service person for
assistance.
TROUBLESHOOTING
Reset Operation
If a voltage spike or static discharge blanks out the display or
causes erratic thermostat operation you can reset the thermostat
by pressing , and TIME at the same time. This also
resetsthe factory defaults. Ifthe thermostat has power,has been
reset and still does not function correctly contact your heating/
cooling service person or place of purchase.
Batteries
For optimum performance, we recommend replacing batteries
once a year with fresh “AAA” Energizer®alkaline batteries.
1. Move the SYSTEM switch to HEAT position.
2. Press PRGM to view the 1st Monday heating period time and
temperature. Each time you press PRGM, the next heating
period time and temperature for Monday will be displayed in
sequence. Press HOLD to display Tuesday’s 1st heating
period program. Press PRGM to check the remaining Tues-
day heating period times and temperatures. To check each
day’s heating program, press HOLD to change days, then
press PRGM to look at each programming period for the day
(you may change any time or temperature during this proce-
dure).
3. Press RUN.
4. Move SYSTEM switch to COOL position.
5. Repeat step 2 to check cooling temperatures.
6. Press RUN to beging program operation.
YOURTHERMOSTATISNOWCOMPLETELYPROGRAMMED
ANDREADYTOAUTOMATICALLYPROVIDEMAXIMUMCOM-
FORT AND EFFICIENCY!
9
NOTE
ELECTRICAL DATA
Electrical Rating:
0 to 30 VAC 50/60 Hz. or D.C.
0.05 to 1.2 Amps (Load per terminal)
1.5 Amps Maximum Total Load (All terminals combined)
THERMAL DATA
Setpoint Temperature Range:
45°F to 90°F (7°C to 32°C)
Operating Ambient Temperature Range:
32°F to 105°F
Operating Humidity Range:
0 to 90% RH (non-condensing)
Shipping Temperature Range:
-40°F to 150°F
SPECIFICATIONS
8

Symptom Possible Cause Corrective Action
No Heat (continued) 5. Heating system requires service or Diagonistic: Set System Switch to Heat and raise
thermostat requires replacement. the setpoint above room temperature. Within a few
seconds the thermostat should make a soft click
sound. This sound usually indicates the thermo-
stat is operating properly. If the thermostat does
not click, try the reset operation listed above. If the
thermostat does not click after being reset contact
your heating and cooling service person or place
of purchase for a replacement. If the thermostat
clicks, contact the furnace manufacturer or a
service person to verify the heating is operating
correctly.
No Cool 1. System Switch not set to Cool. Set System Switch to Cool and lower temp below
room temp.
2. Loose connection to thermostat or system. Verify thermostat and system wires are securely
attached.
3. Cooling system requires service or Same procedure as diagnostic for No Heat
thermostat requires replacement. condition except set the thermostat to Cool and
lower the setpoint below the room temperature.
There may be up to a five minute delay before the
thermostat clicks in Cooling.
Heat, Cool or Fan Runs Constantly. 1. Possible short in wiring. Check each wire connection to verify they are not
2. Possible short in thermostat. shorted or touching together. No bare wire should
3. Possible short in heat/cool/fan system. stick out from under terminal screws. Try resetting
4. Fan Switch set to Fan On. the thermostat as described below. If the condition
persists the manufacturer of your system or
service person can instruct you on how to test the
Heat/Cool system for correct operation. If the
system operates correctly, replace the thermostat.
Furnace Cycles Too Fast or Too Slow 1. The location of the thermostat and/or the Digital thermostats normally provide precise
(narrow or wide temperature swing) size of the Heating System may be temperature control and may cycle faster than
influencing the cycle rate. some older mechanical models. A faster cycle
rate means the unit turns on and off more
frequently but runs for a shorter time so there is
no increase in energy use. If you would like to
increase the cycle time, change the cycle rate to
“SL” in the configuration menu. It is not possible to
shorten the cycle time. If an acceptable cycle rate
is not achieved as received or by changing the
cycle rate. Contact a local service person for
additional suggestions.
Cooling Cycles Too Fast or Too Slow 1. The location of the thermostat and the size The cycle rate for cooling is fixed and can not be
(narrow or wide temperature swing) of the Cooling System can influence the adjusted. Contact a local service person for
cyclerate. suggestions.
Thermostat Setting and Thermostat 1. Thermostat thermometer setting requires The thermometer can be adjusted +/- 4 degrees.
Thermometer Disagree adjustment. See Temperature Display Adjustment in the
Configuration menu.
Thermostat Does Not Follow Program 1. AM or PM set incorrectly in program. Check current clock and program settings
2. AM or PM set incorrectly on the clock. including the AM or PM designations for each
3. Voltage spike or static discharge. time period. If a voltage spike or a static discharge
occurs use the Reset Operation listed above.
Blank Display and/or Keypad 1. Voltage spike or static discharge. Replace batteries and check heat/cool system
Not Responding 2. Battery change required. for proper operation. If a voltage spike occurs use
the Reset Operation listed above.
Clock Loses or Gains Time 1. Loss of power to thermostat and low batteries. The thermostat will maintain its program in
memory even with no power/no batteries but the
clock time will be incorrect when power is
restored. See No Heat/No Cool/No Fan (common
problems) above for items to check in the system.
Heat or Cool Starts Early 1. EMR activated. See Configuration Menu (Item 4).
TROUBLESHOOTING
CONTINUED FROM SEVENTH PAGE
www.white-rodgers.com
9