White Rodgers 179 User manual

If in doubt about whether your wiring is millivolt, line, or low
voltage, have it inspected by a qualified heating and air condi-
tioning contractor or electrician.
Do not exceed the specification ratings.
Allwiringmustconformtolocalandnationalelectricalcodesand
ordinances.
This control is a precision instrument, and should be handled
carefully.Roughhandlingordistortingcomponentscouldcause
the control to malfunction.
This control has been accurately calibrated at the factory. Any
attempt to calibrate this control will void the White-Rodgers
warranty.
Toprevent electricalshockand/orequipmentdamage
disconnect electric power to system at main fuse or
circuit breaker box until installation is complete.
Label all wires prior to disconnection when servicing
controls. Wiring errors can cause improper and dan-
gerous operation.
Following installation or replacement, follow appli-
ance manufacturer’s recommended installation and/
or service instructions to insure proper operation.
Do not use on circuits exceeding specified voltage.
Higher voltage will damage control and could cause
shock or fire hazard.
These room thermostats are specially designed to control
combination heating and cooling equipment that operates on
line voltage.
These controls are suitable for fans or water solenoids on
heating/cooling convectors or any similar application that re-
quires a heavy duty room thermostat with single pole, double
throw (SPDT) switch action.
PRECAUTIONS
NOTE
CAUTION
!
WARNING
!
Printed in U.S.A.
Type 179
SPDT Heating/Cooling Room Thermostat
FAILURETOREADANDFOLLOWALLINSTRUCTIONSCAREFULLYBEFORE
INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL
INJURY AND/OR PROPERTY DAMAGE.
DESCRIPTION
Operator: Save these instructions for future use!
INSTALLATION INSTRUCTIONS
WHITE-RODGERS DIVISION
EMERSON ELECTRIC CO.
9797 REAVIS ROAD
ST. LOUIS, MISSOURI 63123-5398
WHITE-RODGERS
PART NO. 37-0885B
Replaces 37-0885A
0017
SPECIFICATIONS
90
80
70
60
50
40
W
H
I
T
E
-
R
O
D
G
E
R
S
Blue
Red
Common Open on rise
of temperature
Close on rise
of temperature
White
These controls have a single pole, double throw (SPDT) snap
action switch. The top left-hand terminal (red) is the common
terminal. The top right-hand terminal (blue) has open-on-rise
switch action. The bottom center terminal (white) has close-on-
rise switch action.
A.C. Motor Rating
Electrical Rating
120 VAC 240 VAC
Full Load Current
Locked Rotor Current
Non-Inductive
7.4 A
44.5 A
24 A
3.7 A
22.2 A
20 A

THERMOSTAT LOCATION
Proper location of the heavy duty room thermostat is very
important to insure acceptable performance. The following
general rules will help determine proper location:
1. It is very important to be sure that the thermostat is in an
area where air circulates around it freely.
2. Never install the thermostat on or near an outside wall.
3. Donotlocatethethermostatnearwindowsordoors,orinany
drafty area.
4. Don’tinstallthethermostatwhereitwillbeaffectedby“false”
heat sources (such as direct sunlight, a stove or any appli-
ance exhaust, steam lines, etc.).
5. Mount the thermostat on a post or a partioning wall, but be
surethattherearenopipes,ductworkorheatsourcesinthat
wall or directly behind it.
6. If the electrical conduit leads into a cooler or warmer room,
plugtheholearoundthewireswithfire-resistantinsulationto
prevent drafts.
Ifthethermostatisused withunitheaters,thefollowing sugges-
tions for locating the thermostat may be helpful (see fig. 2).
1. Position Ain fig. 2 is acceptable if the thermostat is close
enough to the unit heater so that the return air to the heater
flows over the thermostat.
2. Position Bis acceptable if it is not necessary to make
frequent adjustments of the dial setting.
3. PositionCis acceptable ifit issufficientlyfar fromtheheater
that air flowing over the thermostat is not much above the
average room temperature.
4. PositionDis not acceptable because thepost may prevent
air from circulating over the thermostat.
WIRING
,
,
,







,
,
,
,


,
,



Concrete Plaster/
Drywall
Junction Box
Themostat
Conduit
along wall
Conduit
inside wall
WALL INSTALLATION
The mounting plate for this thermostat has two
holes 3
5
/ 16 ”apart for attaching the control on a
standard switch box.
Figure 1
Floor
Return Air
DC A
B
Post
Ceiling
Unit Partition wall
or post directly
behind unit
Figure 2
All wiring should be done in accordance with local and national electrical codes and ordinances.
Room
Thermostat Manual Switch
Line
Heating
Cooling
Fan or Water
Solenoid
RB
W
Follow the wiring instructions provided by the heating/cooling
equipment manufacturer. If none are offered, a typical circuit
application is shown at right.
Tosetthethermostat,simplymovethedialsothattheindicating
lineon thecase pointsto thedesired temperaturesettingonthe
dial.
OPERATION
70
60
80
Indicating
Line