Wido TVSTAND2 User manual

A B C D
E F G H
TV Stand with LED Strip
Model: TVSTAND2

Safety Notes:
















C1
C2
45pcs 11pcs 2pcs 8pcs
44pcs 5pcs 8pcs 1pcs

12
34
4
5
10
94
5
3
6
8
7
A
8x (E) 8x (G) 4x (A) 2x (B)
2x (A) 1x (B) 6x (A) 2x (B) 20x (E) 5x (F)

56
78
14
13
12
9
10
11
C1
E
1
2
ABA
Front
4x (A) 2x (B) 2x (C1) 8x (E) 4x (A)
4x (A) 2x (B) 4x (A) 2x (B)

910
11 12
15
18 19
16
E
I
I
17
C2
9x (A)
x2
4x (A) 4x (D) 2x (C2) 4x (E)
1x (H)

R
G
B
W
FLASH
STROBE
FADE
SMOOTH
LED CONTROLLER
IR RECEIVER
LED LIGHT STRIP
TRANSFORMER
OFF ON
R G B W
FLASH
STROBE
FADE
SMOOTH
Pull out ba�ery tray to
insert/replace ba�eries
in the remote
REMOTE

Remove contents from the packaging and ensure all parts are included. Check for any signs of
damage to components.
Clean the surface onto which you wish to mount the product. The surface must be clean, free from
dust, grease and dry. Otherwise the stickiness of the doublesided adhesive tape might be affected.
Install the LED light strip in desired location with double sided tape on the back of the strip. Ensure the
connector is positioned on the side where the mains power socket is located.
Attach the LED controller to the LED strip, ensuring the arrows on both connectors align.
Connect the transformer to LED controller and plug in to mains power supply. Ensure the transformer
is always accessible.
Remove the insulating strip from the battery compartment of the remote.
1.
2.
3.
4.
5.
6.
LIGHT SET INSTALLATION
Switch on the light stip using ON - OFF buttons on the remote. The off button on the remote control is
only suitable for switching the light set off temporarily. Always unplug the transformer from mains
power supply to switch it off permanently.
Aim the remote control directly at the infrared receiver for best reception. Ensure that there are no
obstacles between the sender and the receiver.
You can control the light effects using the remote control function buttons. The following settings are
available:
1.
2.
3.
OPERATING THE LIGHT STRIP








Select one of pre-mixed colours


OFF ON
LIGHT CHAIN
LED DRIVER
TRANSFORMER
TECHNICAL SPECIFICATION
AD/DC Adaptor (Model: LX1202)
Input100–240V~ 50/60Hz | Output 12V 2A
LED Driver
Input 12V
Remote Control
3V Lithium battery type CR2025

Please read all instructions and safety notes before use. Failure to follow all instructions listed below may result in damage to the light set. Please save these instructions for
future reference.
Ensure that the available network voltage agrees with the required operational voltage of the device before use (100–240V~).
This product is to be used as decoration only. Not suitable for illuminating rooms on its own.
Not to be used as a toy.
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge
if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall not be made by children without supervision.
The extremely high speed of the light change during the colour change effect can under certain circumstances result in visual impairment of children or predisposed persons
(e.g. by mental illness).
Do not leave light set switched on unattended and when there are no adults present.
This lighting set is suitable for indoor use only.
Always connect transformer to an indoor socket. The transformer and controller must be kept indoors.
Do not use bunched together or use in a confined space where normal air circulation is restricted.
Do not try to connect this light chain electrically to another chain by cutting or joining sets together.
Do not connect to the power supply whilst the product is in the packaging.
LEDs are non-replaceable. Do not attempt to replace LED bulbs that stopped working.
Do not expose the product to high temperatures or moisture, otherwise the product may be damaged.
Protect the product from sharp edges, mechanical loads and hot surfaces.
Take care not to damage the cable or fittings. Do not use if the bulbs, installation of the light set or cable is damaged.
Avoid damaging the insulated cables when installing the set. Always inspect for damage before use.
Do not secure with sharp staples or nails.
The external flexible cable or cord of this light chain cannot be replaced; if the cord is damaged, the light set must be disposed of safely.
If the cable is damaged the lighting set must be disposed of safely.
The lighting chain must be used with the supplied transformer only. Use of any other transformer may create a risk of injury or fire.
Unplug when not in use for any length of time (e.g. holidays). Always unplug from the mains supply throughout installation, maintenance or adjustment.
LIGHT SET SAFETY INFORMATION
BATTERY SAFETY INFORMATION
WARNING! DANGER TO LIFE! Batteries are not intended for children. Do not leave batteries lying around. They may otherwise be swallowed by children or pets. If
accidentally swallowed seek immediate medical attention. Do not use non-rechargeable batteries. Different types of batteries or new & used batteries are not to be mixed.
Batteries are to be inserted with the correct polarity. Exhausted batteries are not to be removed from the toy. The supply terminals are not to be short-circuited.
DISPOSAL
To protect the environment, do not dispose of electric equipment together with household waste material!
In observance of European Directive 2012/19/EU on waste electric and electronic equipment and its
implementation in accordance with national law, electric equipment that have reached the end of their life
must be collected separately and returned to an environmentally compatible recycling facility.