Wilden Saniflo PX8 Instruction Manual

Where Innovation Flows
www.wildenpump.com
EOM
Engineering
Operation &
Maintenance
WIL-12310-E-04
TO REPL ACE WIL-12310 - E- 03
PX8
Sanio
™
Hygienic Series
Metal Pumps

SECTION 1 CAUTIONS—READ FIRST! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
SECTION 2 WILDEN PUMP DESIGNATION SYSTEM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
SECTION 3 HOW IT WORKS—PUMP & AIR DISTRIBUTION SYSTEM . . . . . . . . . . . . . . . .3
SECTION 4 DIMENSIONAL DRAWINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
SECTION 5 PERFORMANCE
A. PX8 Performance Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Operating Principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
How to Use this Curve. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Rubber-Fitted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
TPE-Fitted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Full Stroke PTFE-Fitted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Full Stroke SIPD-Fitted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Reduced Stroke PTFE-Fitted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Reduced Stroke SIPD-Fitted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Reduced Stroke Ultra-Flex™-Fitted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
B. Suction Lift Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
SECTION 6 SUGGESTED INSTALLATION, OPERATION & TROUBLESHOOTING. . . . . . .21
SECTION 7 ASSEMBLY / DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
SECTION 8 CLEANING - CIP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
SECTION 9 EXPLODED VIEW & PARTS LISTING
PX8 Saniflo™ HS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
SECTION 10 ELASTOMER OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
TABLE OF CONTENTS

Section 1
CAUTIONS—READ FIRST!
WIL-12310-E-04 1 WILDEN PUMP & ENGINEERING, LLC
CAUTION: Do not apply compressed air to the
exhaust port — pump will not function.
CAUTION: Do not over-lubricate air supply —
excess lubricationwillreducepump performance.
Pump is pre-lubed.
TEMPERATURE LIMITS:
Neoprene –17.7°C to 93.3°C 0°F to 200°F
Buna-N –12.2°C to 82.2°C 10°F to 180°F
Nordel®–51.1°C to 137.8°C –60°F to 280°F
Viton®–40°C to 176.7°C –40°F to 350°F
Saniflex™ –28.9°C to 104.4°C –20°F to 220°F
Polytetrafluoroethylene (PTFE)
4.4°C to 104.4°C 40°F to 220°F
Polyurethane –12.2°C to 65.6°C 10°F to 150°F
Tetra-Flex™ PTFE w/Neoprene Backed
4.4°C to 107.2°C 40°F to 225°F
Tetra-Flex™ PTFE w/Nordel®Backed
-10°C to 137°C 14°F to 280°F
Wil-Flex™ (Santoprene®)
-40°C to 107.2°C -40°F to 225°F
NOTE: Not all materials are available for all
models. Refer to Section 2 for material options
for your pump.
CAUTION: When choosing pump materials, be
sure to check the temperature limits for all wetted
components. Example: Viton®has a maximum
limit of 176.7°C (350°F) but polypropylene has a
maximum limit of only 79°C (175°F).
CAUTION: Maximum temperature limits are
based upon mechanical stress only. Certain
chemicals will significantly reduce maximum
safe operating temperatures. Consult Chemical
Resistance Guide (E4) for chemical compatibility
and temperature limits.
WARNING: Prevention of static sparking — If
static sparking occurs, fire or explosion could
result. Pump, valves, and containers must be
grounded to a proper grounding point when
handling flammable fluids and whenever
discharge of static electricity is a hazard.
CAUTION: Do not exceed 8.6 bar (125 psig) air
supply pressure.
CAUTION: The process fluid and cleaning fluids
must be chemically compatible with all wetted
pump components. Consult Chemical Resistance
Guide (E4).
CAUTION: Do not exceed 82°C (180°F) air inlet
temperature for Pro-Flo X™ models.
CAUTION: Pumps should be thoroughly flushed
before installing into process lines. FDA and
USDA approved pumps should be cleaned and/
or sanitized before being used.
CAUTION: Always wear safety glasses when
operating pump. If diaphragm rupture occurs,
material being pumped may be forced out air
exhaust.
CAUTION: Before any maintenance or repair is
attempted, the compressed air line to the pump
should be disconnected and all air pressure
allowed to bleed from pump. Disconnect all
intake, discharge and air lines. Drain the pump
by turning it upside down and allowing any fluid
to flow into a suitable container.
CAUTION: Blow out air line for 10 to 20 seconds
before attaching to pump to make sure all pipeline
debris is clear. Use an in-line air filter.A 5µ (micron)
air filter is recommended.
NOTE: When installing PTFE diaphragms, it is
important to tighten outer pistons simultaneously
(turning in opposite directions) to ensure tight fit.
(See torque specifications in Section 7.)
NOTE: Cast Iron PTFE-fitted pumps come
standard from the factory with expanded PTFE
gaskets installed in the diaphragm bead of the
liquid chamber. PTFE gaskets cannot be re-used.
Consult PS-TG for installation instructions during
reassembly.
NOTE: Before starting disassembly, mark a line
from each liquid chamber to its corresponding air
chamber. This line will assist in proper alignment
during reassembly.
CAUTION: Pumps are available in both
submersible and non-submersible options. Do
not use non-submersible Pro-Flo X™ models in
submersible applications.
CAUTION: Tighten all hardware prior to installation.

WILDEN PUMP & ENGINEERING, LLC 2 WIL-12310-E-04
Section 2
WILDEN PUMP DESIGNATION SYSTEM
PX8 SANIFLO™
HYGIENIC SERIES
51 mm (2") Pump
Maximum Flow Rate:
587 lpm (155 gpm)
LEGEND
PX8 / XXXXX / XXX / XX/ XX/ XXXX
GASKETS
MODEL
VALVE OPTION
DIAPHRAGMS
AIR VALVE
AIR CHAMBER
CENTER SECTION
WETTED PARTS & OUTER PISTON
SPECIALTY
CODE
(if applicable)
SPECIALTY CODES
MATERIAL CODES
MODEL
PX8 = 51 mm (2")
XPX8 = 51 mm (2") ATEX
WETTED PARTS/
OUTER PISTON
SS = 316L STAINLESS STEEL
SZ = 316L STAINLESS STEEL/
NO PISTON
CENTER BLOCK
N = NICKEL PLATED ALUMINUM
S = 316 STAINLESS STEEL
AIR CHAMBERS
N = NICKEL PLATED ALUMINUM
S = 316 STAINLESS STEEL
AIR VALVE
N = NICKEL PLATED ALUMINUM
S = 316 STAINLESS STEEL
DIAPHRAGMS
BNU = ULTRA-FLEX™ BUNA1,5
EPU = ULTRA-FLEX™ EPDM1,5
FBS = SANITARY BUNA1
(two yellow dots)
FES = SANITARY EPDM1
(two blue dots)
FSS = SANIFLEX™
1
FWL = FULL STROKE SANITARY
WIL-FLEX™ IPD1,3,4
FWS = SANITARY WIL-FLEX™
1
LEL = PTFE-EPDM BACKED
LAMINATE IPD1,2,3,4,5
TEU = PTFE w/EPDM BACKUP1,2,5
TSS = FULL STROKE PTFE
w/SANIFLEX™ BACK-UP1,2
TSU = PTFE w/SANIFLEX™
BACK-UP1,2,5
TWS = FULL STROKE PTFE
w/WIL-FLEX™ BACK-UP1,2
VALVE BALLS, FLAP VALVES,
MUSHROOM CHECK
FB = SANITARY BUNA1,3,4
(red dot)
FE = SANITARY EPDM1,3,4
(green dot)
FS = SANIFLEX™
1,3,4
FW = SANITARY WIL-FLEX™ 1,3,4
SF = STAINLESS STEEL FLAP1,5
TF = PTFE1,2,3,4
TM = PTFE MUSHROOM
CHECK1,2
MANIFOLD GASKET
FB = SANITARY BUNA-N1,3,4
(red dot)
FE = SANITARY EPDM1,3,4
(green dot)
FV = SANITARY VITON®1, 3, 4
(one white/one
yellow dots)
TF = PTFE1,2,3,4,5
NOTE: MOST ELASTOMERIC MATERIALS USE COLORED DOTS FOR IDENTIFICATION.
Viton®is a registered trademark of DuPont Dow Elastomers.
0770 SaniFlo HS
0771 SaniFlo HS, w/Swivel Stand
0772 SaniFlo HS, Wil-Gard 110V
0773 SaniFlo HS, Wil-Gard 220V
0774 HS, Wil-Gard 110V, w/Swivel Stand
0775 SaniFlo HS, Wil-Gard 220V, w/Swivel Stand
0778 SaniFlo HS, DIN Connection
0779 HS, w/Swivel Stand DIN Connection
0780 SaniFlo HS, Wil-Gard 110V DIN Connection
0781 SaniFlo HS, Wil-Gard 220V DIN Connection
0782 SaniFlo HS, Wil-Gard 110V, w/Swivel Stand DIN Connection
0783 SaniFlo HS, Wil-Gard 220V, w/Swivel Stand DIN Connection
0784 SaniFlo HS, SMS Connection
0785 SaniFlo HS, w/Swivel Stand SMS Connection
0786 SaniFlo HS, Wil-Gard 110V SMS Connection
0787 SaniFlo HS, Wil-Gard 220V SMS Connection
0788 SaniFlo HS, Wil-Gard 110V, w/Swivel Stand SMS Connection
0789 SaniFlo HS, Wil-Gard 220V, w/Swivel Stand SMS Connection
NOTE:
1. Meets Requirements of FDA CFR21.177
2. Meets Requirements of USPClass VI
3. Required for EHEDG Certification
4. Required for 3-A Certification
5. Stainless flap valve not available with reduced stroke PTFE, reduced
stroke Ultra-FlexTM or reduced stroke Laminate IP diaphragms

WIL-12310-E-04 3 WILDEN PUMP & ENGINEERING, LLC
The Wilden diaphragm pump is an air-operated, positive displacement, self-priming pump. These drawings show flow pattern
through the pump upon its initial stroke. It is assumed the pump has no fluid in it prior to its initial stroke.
FIGURE 1 The air valve directs pressurized
air to the back side of diaphragm A. The
compressed air is applied directly to the
liquid column separated by elastomeric
diaphragms. The diaphragm acts as
a separation membrane between the
compressed air and liquid, balancing the
load and removing mechanical stress
from the diaphragm. The compressed
air moves the diaphragm away from
the center of the pump. The opposite
diaphragm is pulled in by the shaft
connected to the pressurized diaphragm.
Diaphragm B is on its suction stroke; air
behind the diaphragm has been forced
out to atmosphere through the exhaust
port of the pump. The movement of
diaphragm B toward the center of the
pump creates a vacuum within chamber B.
Atmospheric pressure forces fluid into
the inlet manifold forcing the inlet valve
ball off its seat. Liquid is free to move
past the inlet valve ball and fill the liquid
chamber (see shaded area).
FIGURE 2 When the pressurized diaphragm,
diaphragm A, reaches the limit of its discharge
stroke, the air valve redirects pressurized
air to the back side of diaphragm B. The
pressurized air forces diaphragm B away
from the center while pulling diaphragm A
to the center. Diaphragm B is now on its
discharge stroke. Diaphragm B forces the
inlet valve ball onto its seat due to the
hydraulic forces developed in the liquid
chamber and manifold of the pump. These
same hydraulic forces lift the discharge
valve ball off its seat, while the opposite
discharge valve ball is forced onto its seat,
forcing fluid to flow through the pump
discharge. The movement of diaphragm A
toward the center of the pump creates a
vacuum within liquid chamber A. Atmos-
pheric pressure forces fluid into the inlet
manifold of the pump. The inlet valve ball
is forced off its seat allowing the fluid being
pumped to fill the liquid chamber.
FIGURE 3 At completion of the stroke,
the air valve again redirects air to the
back side of diaphragm A, which starts
diaphragm B on its exhaust stroke. As
the pump reaches its original starting
point, each diaphragm has gone through
one exhaust and one discharge stroke.
This constitutes one complete pumping
cycle. The pump may take several cycles
to completely prime depending on the
conditions of the application.
OUTLET
CLOSED
CLOSEDOPEN
OPEN
INLET
BA
OUTLET
OPEN
OPENCLOSED
CLOSED
INLET
BA
OUTLET
CLOSED
CLOSEDOPEN
OPEN
INLET
BA
Section 3
HOW IT WORKS—PUMP

WILDEN PUMP & ENGINEERING, LLC 4 WIL-12310-E-04
Section 4
DIMENSIONAL DRAWINGS
PX8 Saniflo™ HS Fixed
D
C
B
A
M
L
P
N
R
J
K
H
G
E
25 mm (1")
FNPT AIR
EXHAUST
19 mm (3/4")
FNPT AIR
INLET
51 mm
(2")
TRI-
CLAMP
INLET
F
F
51 mm (2")
TRI-CLAMP
DISCHARGE
PX8 Saniflo™ HS Flap Valve Fixed
DIMENSIONS
ITEM METRIC (mm) STANDARD (inch)
A 460 18.1
B 213 8.4
C 577 22.7
D 902 35.5
E 955 37.6
F 51 2.0
G 579 22.8
H 363 14.3
J 559 22.0
K 46 1.8
L 401 15.8
M 351 13.8
N 318 12.5
P 356 14.0
Rø10 ø0.4
DIMENSIONS
ITEM METRIC (mm) STANDARD (inch)
A 460 18.1
B 160 6.3
C 577 22.7
D 955 37.6
E 1008 39.7
F 51 2.0
G 579 22.8
H 363 14.3
J 559 22.0
K 56 2.2
L 401 15.8
M 351 13.8
N 318 12.5
P 356 14.0
Rø10 ø0.4
Rev A
Rev A

WIL-12310-E-04 5 WILDEN PUMP & ENGINEERING, LLC
Section 4
DIMENSIONAL DRAWINGS
PX8 Saniflo™ HS Swivel
PX8 Saniflo™ HS Flap Valve Swivel
Rev B
Rev B
DIMENSIONS
ITEM METRIC (mm) STANDARD (inch)
A 460 18.1
B 247 9.7
C 612 24.1
D 938 36.9
E 989 38.9
F 51 2.0
G 615 24.2
H 498 19.6
J 693 27.3
K 46 1.8
L 401 15.8
M 351 13.8
N 394 15.5
P 432 17.0
R ø10 ø0.4
DIMENSIONS
ITEM METRIC (mm) STANDARD (inch)
A 460 18.1
B 194 7.6
C 612 24.1
D 990 39.0
E 1042 41.0
F 51 2.0
G 615 24.2
H 498 19.6
J 693 27.3
K 56 2.2
L 401 15.8
M 351 13.8
N 394 15.5
P 432 17.0
R ø10 ø0.4

WILDEN PUMP & ENGINEERING, LLC 6 WIL-12310-E-04
Pump Solids
Maximize Your Yield
• 3 sizes available
• Solids passage to 152 mm (6")
• Stainless steel construction
• Only 2 moving parts
• Low liquid content requirement
• Complies with
USDA requirements
• Variable flow
• CE marked
• Low voltage directive by TÜV
• PED & machinery directive
Is your process limping along with a pump that wasn't
designed to transfer sanitary solids? Are your inspection,
cleaning, and maintenance costs too high? Are you looking
for a pump that is actually designed for your application?
Wilden has your answer. The Saniflo™ VC pump can trans-
fer your product without damage from bruising or shearing.
The pump is specifically designed to meet your performance
needs while minimizing cleaning and inspection time. Contact
us for a unique perspective and proven results. The Saniflo™
VC will handle any food product that you can dish out.

PX8
PX8 SANIFLO HS PERFORMANCE
SANIFLO

The Pro-Flo X™ air distribution system with the
revolutionary Efficiency Management System (EMS)
offers flexibility never before seen in the world of
AODD pumps. The
patent-pending EMS
is simple and easy
to use. With the
turn of an integrated
control dial, the operator can select the optimal
balance of flow and efficiency that best meets the
application needs. Pro-Flo X™ provides higher
performance, lower
operational costs
and flexibility that
exceeds previous
industry standards.
Pro-Flo XTM Operating Principle
Section 5A
Turning the dial
changes the
relationship
between air inlet
and exhaust
porting.
Each dial setting
represents an
entirely different
flow curve
Pro-Flo X™ pumps
are shipped from
the factory on
setting 4, which
is the highest
flow rate setting
possible
Moving the dial
from setting 4
causes a decrease
in flow and an even
greater decrease in
air consumption.
When the air
consumption
decreases more
than the flow
rate, efficiency
is improved and
operating costs
are reduced.
$
$
$
AIR CONSUMPTION
WILDEN PUMP & ENGINEERING, LLC 8 PX8 HS Performance

HOW TO USE THIS EMS CURVE
PX8 HS Performance 9 WILDEN PUMP & ENGINEERING, LLC
SETTING 4 PERFORMANCE CURVE EMS CURVE
8.2 GPM
Example data point = Example data point =
Figure 1 Figure 2
0.58
0.48
flow multiplier
air multiplier
This is an example showing how to determine flow rate and
air consumption for your Pro-Flo X™ pump using the Efficien-
cy Management System (EMS) curve and the performance
curve. For this example we will be using 4.1 bar (60 psig) inlet
air pressure and 2.8 bar (40 psig) discharge pressure and EMS
setting 2.
Step 1: Identifying performance at setting 4. Locate
the curve that represents the flow rate of the
pump with 4.1 bar (60 psig) air inlet pressure.
Mark the point where this curve crosses the
horizontal line representing 2.8 bar (40 psig)
discharge pressure. (Figure 1). After locating
your performance point on the flow curve,
draw a vertical line downward until reaching
the bottom scale on the chart. Identify the flow
rate (in this case, 8.2 gpm). Observe location
of performance point relative to air consump-
tion curves and approximate air consumption
value (in this case, 9.8 scfm).
Step 2: Determining flow and air X Factors. Locate
your discharge pressure (40 psig) on the verti-
cal axis of the EMS curve (Figure 2). Follow
along the 2.8 bar (40 psig) horizontal line until
intersecting both flow and air curves for your
desired EMS setting (in this case, setting 2).
Mark the points where the EMS curves inter-
sect the horizontal discharge pressure line.
After locating your EMS points on the EMS
curve, draw vertical lines downward until
reaching the bottom scale on the chart. This
identifies the flow X Factor (in this case, 0.58)
and air X Factor (in this case, 0.48).
Step 3: Calculating performance for specific EMS
setting. Multiply the flow rate (8.2 gpm)
obtained in Step 1 by the flow X Factor multi-
plier (0.58) in Step 2 to determine the flow rate
at EMS setting 2. Multiply the air consump-
tion (9.8 scfm) obtained in Step 1 by the air
X Factor multiplier (0.48) in Step 2 to deter-
mine the air consumption at EMS setting 2
(Figure 3).
Figure 3
The flow rate and air consumption at Setting
2 are found to be 18.2 lpm (4.8 gpm) and 7.9
Nm3/h (4.7 scfm) respectively.
.58
4.8 gpm
(Flow X Factor setting 2)
(Flow rate for setting 2)
(air consumption for setting 4)
(Air X Factor setting 2)
(air consumption for setting 2)
9.8 scfm
.48
4.7 scfm
8.2 gpm (flow rate for Setting 4)
Example 1

HOW TO USE THIS EMS CURVE
WILDEN PUMP & ENGINEERING, LLC 10 PX8 HS Performance
EMS CURVE
SETTING 4 PERFORMANCE CURVE
This is an example showing how to determine the inlet air
pressure and the EMS setting for your Pro-Flo X™ pump to
optimize the pump for a specific application. For this exam-
ple we will be using an application requirement of 18.9 lpm
(5 gpm) flow rate against 2.8 bar (40 psig) discharge pressure.
This example will illustrate how to calculate the air consump-
tion that could be expected at this operational point.
Step 1 : Establish inlet air pressure. Higher air pres-
sures will typically allow the pump to run
more efficiently, however, available plant air
pressure can vary greatly. If an operating
pressure of 6.9 bar (100 psig) is chosen when
plant air frequently dips to 6.2 bar (90 psig)
pump performance will vary. Choose an oper-
ating pressure that is within your compressed
air system's capabilities. For this example we
will choose 4.1 bar (60 psig).
Step 2 : Determine performance point at setting 4. For
this example an inlet air pressure of 4.1 bar
(60 psig) inlet air pressure has been chosen.
Locate the curve that represents the perfor-
mance of the pump with 4.1 bar (60 psig) inlet
air pressure. Mark the point where this curve
crosses the horizontal line representing 2.8
bar (40 psig) discharge pressure. After locat-
ing this point on the flow curve, draw a verti-
cal line downward until reaching the bottom
scale on the chart and identify the flow rate.
In our example it is 38.6 lpm (10.2 gpm). This
is the setting 4 flow rate. Observe the loca-
tion of the performance point relative to air
consumption curves and approximate air
consumption value. In our example setting
4 air consumption is 24 Nm3/h (14 scfm).
See figure 4.
Step 3 : Determine flow X Factor. Divide the required
flow rate 18.9 lpm (5 gpm) by the setting 4 flow
rate 38.6 lpm (10.2 gpm) to determine the flow
X Factor for the application.
Step 4 : Determine EMS setting from the flow
X Factor. Plot the point representing the flow
X Factor (0.49) and the application discharge
pressure 2.8 bar (40 psig) on the EMS curve.
This is done by following the horizontal 2.8
bar (40 psig) psig discharge pressure line until
it crosses the vertical 0.49 X Factor line. Typi-
cally, this point lies between two flow EMS
setting curves (in this case, the point lies be-
tween the flow curves for EMS setting 1 and
2). Observe the location of the point relative
to the two curves it lies between and approxi-
mate the EMS setting (figure 5). For more pre-
cise results you can mathematically interpo-
late between the two curves to determine the
optimal EMS setting.
5 gpm / 10.2 gpm = 0.49 (flow X Factor)
DETERMINE EMS SETTING
For this example the EMS setting is 1.8.
Figure 4
Example data point = 10.2 gpm flow multiplier
Figure 5
EMS Flow
Settings 1 & 2
Example 2.1
0.49

HOW TO USE THIS EMS CURVE
PX8 HS Performance 11 WILDEN PUMP & ENGINEERING, LLC
EMS CURVE
SETTING 4 PERFORMANCE CURVE
Example 2.2
Determine air consumption at a specific
EMS setting.
Step 1 : Determine air X Factor. In order to determine
the air X Factor, identify the two air EMS set-
ting curves closest to the EMS setting estab-
lished in example 2.1 (in this case, the point lies
between the air curves for EMS setting 1 and
2). The point representing your EMS setting
(1.8) must be approximated and plotted on the
EMS curve along the horizontal line represent-
ing your discharge pressure (in this case, 40
psig). This air point is different than the flow
point plotted in example 2.1. After estimating
(or interpolating) this point on the curve, draw
a vertical line downward until reaching the
bottom scale on the chart and identify the air
X Factor (figure 7).
Step 2 : Determine air consumption. Multiply your
setting 4 air consumption (14 scfm) value by
the air X Factor obtained above (0.40) to deter-
mine your actual air consumption.
In summary, for an application requiring 18.9 lpm
(5 gpm) against 2.8 bar (40 psig) discharge pressure,
the pump inlet air pressure should be set to 4.1 bar
(60 psig) and the EMS dial should be set to 1.8. The
pump would then consume 9.5 Nm3/h (5.6 scfm) of
compressed air.
Figure 6
0.40 air multiplier
Example data point =
Figure 7
10.2 gpm
Example data point =
For this example the air X Factor is 0.40
1 4 scfm x 0.40 = 5.6 SCFM
EMS Air
Settings 1 & 2

PERFORMANCE
WILDEN PUMP & ENGINEERING, LLC 12 PX8 HS Performance
SETTING 4 PERFORMANCE CURVE EMS CURVE
PX8 SANIFLO HS FULL STROKE RUBBER-FITTED
TECHNICAL DATA Height . . . . . . . . . . . . . . . . . . . . . . . . . 1008 mm (39.7”) Width. . . . . . . . . . . . . . . . . . . . . . . . . . . 460 mm (18.1”) Depth. . . . . . . . . . . . . . . . . . . . . . . . . . . 498 mm (19.6”) Ship Weight . . . . . . . . . . . . . . . . . . . . . 49 kg (109 lbs.) Air Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 mm (3/4”) Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 mm (2”) Outlet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 mm (2”) Suction Lift . . . . . . . . . . . . . . . . . . . . . 5.3 m Dry (17.3’) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.0 m Wet (29.5’) Disp. Per Stroke. . . . . . . . . . . . . . . . . . 1.1 l (0.28 gal.)1 Max. Flow Rate . . . . . . . . . . . . . . . .579 lpm (153 gpm) Max. Size Solids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mushroom Valve . . . . . . . . . . . . . . . . . 6.4 mm (1/4”) Ball Valve. . . . . . . . . . . . . . . . . . . . . . . 12.7 mm (1/2”) Flap Valve (compressible solids). 47.5 mm (1-7/8”) Surface Finish . . . . . . . . . . . . . . . . Ra 0.8 µm (32 µ-in) 1Displacement per stroke was calculated at 4.8 bar (70 psig)
air inlet pressure against a 2 bar (30 psig) head pressure.
The Efficiency Management System (EMS) can be used to optimize the performance of your Wilden pump for specific applications. The pump is delivered with the EMS adjusted to setting 4, which allows maximum flow. The EMS curve allows the pump user to deter- mine flow and air consumption at each EMS setting. For any EMS setting and discharge pressure, the “X factor” is used as a multi- plier with the original values from the setting 4 performance curve to calculate the actual flow and air consumption values for that spe- cific EMS setting. Note: you can interpolate between the setting curves for operation at intermediate EMS settings
EXAMPLE A PX8 Saniflo HS, full stroke Rubber-fitted pump operating at EMS setting 4, achieved a flow rate of 348 lpm (92 gpm) using 119 Nm3/h
(70 scfm) of air when run at 5.5 bar (80 psig) air inlet pressure and 2.1 bar (30 psig) discharge pressure (See dot on performance curve). The end user did not require that much flow and wanted to reduce air consumption at his facility. He determined that EMS setting 2 would meet his needs. At 2.1 bar (30 psig) discharge pressure and EMS setting 2, the flow “X factor” is 0.74 and the air “X factor” is 0.48 (see dots on EMS curve). Multiplying the original setting 4 values by the “X factors” provides the setting 2 flow rate of 258 lpm (68 gpm) and an air consumption of 57 Nm3/h (34 scfm). The flow rate was reduced by 26% while
the air consumption was reduced by 52%, thus providing increased efficiency. For a detailed example for how to set your EMS, see beginning of performance curve section. Caution: Do not exceed 8.6 bar (125 psig) air supply pressure.
Flow rates indicated on chart were determined by pumping water with a vertically mounted, center ported ball check configuration. When alternate check valve options are used, multiply flow rate by appropriate factor: Flap check valve = 83%. For optimum life and performance, pumps should be specified so that daily operation parameters fall in the center of the pump performance curve.

PERFORMANCE
PX8 HS Performance 13 WILDEN PUMP & ENGINEERING, LLC
SETTING 4 PERFORMANCE CURVE EMS CURVE
PX8 SANIFLO HS FULL STROKE TPE-FITTED
EXAMPLE A PX8 Saniflo HS, full stroke TPE-fitted pump operating at EMS set- ting 4, achieved a flow rate of 367 lpm (97 gpm) using 102 Nm3/h (60
scfm) of air when run at 4.1 bar (60 psig) air inlet pressure and 1.4 bar (20 psig) discharge pressure (See dot on performance curve). The end user did not require that much flow and wanted to reduce air consumption at his facility. He determined that EMS setting 2 would meet his needs. At 1.4 bar (20 psig) discharge pressure and EMS setting 2, the flow “X factor” is 0.66 and the air “X factor” is 0.47 (see dots on EMS curve). Multiplying the original setting 4 values by the “X factors” provides the setting 2 flow rate of 242 lpm (64 gpm) and an air consumption of 48 Nm3/h (28 scfm). The flow rate was reduced by 34% while
the air consumption was reduced by 53%, thus providing increased efficiency. For a detailed example for how to set your EMS, see beginning of performance curve section. Caution: Do not exceed 8.6 bar (125 psig) air supply pressure.
The Efficiency Management System (EMS) can be used to optimize the performance of your Wilden pump for specific applications. The pump is delivered with the EMS adjusted to setting 4, which allows maximum flow. The EMS curve allows the pump user to deter- mine flow and air consumption at each EMS setting. For any EMS setting and discharge pressure, the “X factor” is used as a multi- plier with the original values from the setting 4 performance curve to calculate the actual flow and air consumption values for that spe- cific EMS setting. Note: you can interpolate between the setting curves for operation at intermediate EMS settings.
TECHNICAL DATA Height . . . . . . . . . . . . . . . . . . . . . . . . .1008 mm (39.7”) Width. . . . . . . . . . . . . . . . . . . . . . . . . . .460 mm (18.1”) Depth. . . . . . . . . . . . . . . . . . . . . . . . . . .498 mm (19.6”) Ship Weight . . . . . . . . . . . . . . . . . . . . .49 kg (109 lbs.) Air Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . 19 mm (3/4”) Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 mm (2”) Outlet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 mm (2”) Suction Lift . . . . . . . . . . . . . . . . . . . . . .1.9 m Dry (6.2’) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.0 m Wet (29.5’) Disp. Per Stroke. . . . . . . . . . . . . . . . . 1.2 l (0.33 gal.)1 Max. Flow Rate . . . . . . . . . . . . . . .587 lpm (155 gpm) Max. Size Solids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mushroom Valve . . . . . . . . . . . . . . . . 6.4 mm (1/4”) Ball Valve. . . . . . . . . . . . . . . . . . . . . . 12.7 mm (1/2”) Flap Valve (compressible solids) 47.5 mm (1-7/8”) Surface Finish . . . . . . . . . . . . . . . Ra 0.8 µm (32 µ-in) 1Displacement per stroke was calculated at 4.8 bar (70 psig)
air inlet pressure against a 2 bar (30 psig) head pressure.
Flow rates indicated on chart were determined by pumping water with a vertically mounted, center ported ball check configuration. When alternate check valve options are used, multiply flow rate by appropriate factor: Flap check valve = 83%. For optimum life and performance, pumps should be specified so that daily operation parameters fall in the center of the pump performance curve.

PERFORMANCE
WILDEN PUMP & ENGINEERING, LLC 14 PX8 HS Performance
SETTING 4 PERFORMANCE CURVE EMS CURVE
PX8 SANIFLO HS FULL STROKE PTFE-FITTED
EXAMPLE A PX8 Saniflo HS, Full Stroke PTFE -fitted pump operating at EMS setting 4, achieved a flow rate of 201 lpm (53 gpm) using 93 Nm3/h
(55 scfm) of air when run at 5.5 bar (80 psig) air inlet pressure and 4.1 bar (60 psig) discharge pressure (See dot on performance curve). The end user did not require that much flow and wanted to reduce air consumption at his facility. He determined that EMS setting 2 would meet his needs. At 4.1 bar (60 psig) discharge pressure and EMS setting 2, the flow “X factor” is 0.70 and the air “X factor” is 0.60 (see dots on EMS curve). Multiplying the original setting 4 values by the “X factors” provides the setting 2 flow rate of 140 lpm (37 gpm) and an air consumption of 56 Nm3/h (33 scfm). The flow rate was reduced by 30% while
the air consumption was reduced by 40%, thus providing increased efficiency. For a detailed example for how to set your EMS, see beginning of performance curve section. Caution: Do not exceed 8.6 bar (125 psig) air supply pressure.
The Efficiency Management System (EMS) can be used to optimize the performance of your Wilden pump for specific applications. The pump is delivered with the EMS adjusted to setting 4, which allows maximum flow. The EMS curve allows the pump user to determine flow and air consumption at each EMS setting. For any EMS setting and discharge pressure, the “X factor” is used as a multiplier with the original values from the setting 4 performance curve to calculate the actual flow and air consumption values for that specific EMS setting. Note: you can interpolate between the setting curves for operation at intermediate EMS settings.
TECHNICAL DATA Height . . . . . . . . . . . . . . . . . . . . . . . . . 1008 mm (39.7”) Width. . . . . . . . . . . . . . . . . . . . . . . . . . . 460 mm (18.1”) Depth. . . . . . . . . . . . . . . . . . . . . . . . . . . 398 mm (15.7”) Ship Weight . . . . . . . . . . . . . . . . . . . . . 49 kg (109 lbs.) Air Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 mm (3/4”) Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 mm (2”) Outlet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 mm (2”) Suction Lift . . . . . . . . . . . . . . . . . . . . . 4.8 m Dry (15.9’) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.6 m Wet (28.4’) Disp. Per Stroke. . . . . . . . . . . . . . . . . . 1.1 l (0.28 gal.)1 Max. Flow Rate . . . . . . . . . . . . . . . .556 lpm (147 gpm) Max. Size Solids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mushroom Valve . . . . . . . . . . . . . . . . . 6.4 mm (1/4”) Ball Valve. . . . . . . . . . . . . . . . . . . . . . . 12.7 mm (1/2”) Surface Finish . . . . . . . . . . . . . . . . Ra 0.8 µm (32 µ-in) 1Displacement per stroke was calculated at 4.8 bar (70 psig)
air inlet pressure against a 2 bar (30 psig) head pressure.
Flow rates indicated on chart were determined by pumping water with a vertically mounted, center ported ball check configuration. When alternate check valve options are used, multiply flow rate by appropriate factor: For optimum life and performance, pumps should be specified so that daily operation parameters fall in the center of the pump performance curve.

PERFORMANCE
PX8 HS Performance 15 WILDEN PUMP & ENGINEERING, LLC
SETTING 4 PERFORMANCE CURVE EMS CURVE
PX8 SANIFLO HS FULL STROKE SIPD-FITTED
(Full Stroke Integral Piston Diaphragm)
EXAMPLE A PX8 Saniflo HS, Full Stroke SIPD -fitted pump operating at EMS setting 4, achieved a flow rate of 390 lpm (103 gpm) using 105 Nm3/h
(62 scfm) of air when run at 4.1 bar (60 psig) air inlet pressure and 1.4 bar (20 psig) discharge pressure (See dot on performance curve). The end user did not require that much flow and wanted to reduce air consumption at his facility. He determined that EMS setting 2 would meet his needs. At 1.4 bar (20 psig) discharge pressure and EMS setting 2, the flow “X factor” is 0.79 and the air “X factor” is 0.54 (see dots on EMS curve). Multiplying the original setting 4 values by the “X factors” provides the setting 2 flow rate of 308 lpm (81 gpm) and an air consumption of 57 Nm3/h (33 scfm). The flow rate was reduced by 21% while
the air consumption was reduced by 46%, thus providing increased efficiency. For a detailed example for how to set your EMS, see beginning of performance curve section. Caution: Do not exceed 8.6 bar (125 psig) air supply pressure.
The Efficiency Management System (EMS) can be used to optimize the performance of your Wilden pump for specific applications. The pump is delivered with the EMS adjusted to setting 4, which allows maximum flow. The EMS curve allows the pump user to determine flow and air consumption at each EMS setting. For any EMS setting and discharge pressure, the “X factor” is used as a multiplier with the original values from the setting 4 performance curve to calculate the actual flow and air consumption values for that specific EMS setting. Note: you can interpolate between the setting curves for operation at intermediate EMS settings.
TECHNICAL DATA Height . . . . . . . . . . . . . . . . . . . . . . . . . 1008 mm (39.7”) Width. . . . . . . . . . . . . . . . . . . . . . . . . . . 460 mm (18.1”) Depth. . . . . . . . . . . . . . . . . . . . . . . . . . . 398 mm (15.7”) Ship Weight . . . . . . . . . . . . . . . . . . . . . 49 kg (109 lbs.) Air Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 mm (3/4”) Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 mm (2”) Outlet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 mm (2”) Suction Lift . . . . . . . . . . . . . . . . . . . . . 4.7 m Dry (15.3’) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.6 m Wet (28.4’) Disp. Per Stroke. . . . . . . . . . . . . . . . . . 1.1 l (0.28 gal.)1 Max. Flow Rate . . . . . . . . . . . . . . . .556 lpm (147 gpm) Max. Size Solids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mushroom Valve . . . . . . . . . . . . . . . . . 6.4 mm (1/4”) Ball Valve. . . . . . . . . . . . . . . . . . . . . . . 12.7 mm (1/2”) Surface Finish . . . . . . . . . . . . . . . . Ra 0.8 µm (32 µ-in) 1Displacement per stroke was calculated at 4.8 bar (70 psig)
air inlet pressure against a 2 bar (30 psig) head pressure.
Flow rates indicated on chart were determined by pumping water with a vertically mounted, center ported ball check configuration. When alternate check valve options are used, multiply flow rate by appropriate factor: For optimum life and performance, pumps should be specified so that daily operation parameters fall in the center of the pump performance curve.

PERFORMANCE
WILDEN PUMP & ENGINEERING, LLC 16 PX8 HS Performance
SETTING 4 PERFORMANCE CURVE EMS CURVE
PX8 SANIFLO HS REDUCED STROKE PTFE-FITTED
TECHNICAL DATA Height . . . . . . . . . . . . . . . . . . . . . . . . .1008 mm (39.7”) Width. . . . . . . . . . . . . . . . . . . . . . . . . . .460 mm (18.1”) Depth. . . . . . . . . . . . . . . . . . . . . . . . . . .498 mm (19.6”) Ship Weight . . . . . . . . . . . . . . . . . . . . .49 kg (109 lbs.) Air Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . 19 mm (3/4”) Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 mm (2”) Outlet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 mm (2”) Suction Lift . . . . . . . . . . . . . . . . . . . . . .2.8 m Dry (9.1’) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.0 m Wet (29.5’) Disp. Per Stroke. . . . . . . . . . . . . . . . . 0.5 l (0.13 gal.)1 Max. Flow Rate . . . . . . . . . . . . . . . .353 lpm (96 gpm) Max. Size Solids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mushroom Valve . . . . . . . . . . . . . . . . 6.4 mm (1/4”) Ball Valve. . . . . . . . . . . . . . . . . . . . . . 12.7 mm (1/2”) Surface Finish . . . . . . . . . . . . . . . Ra 0.8 µm (32 µ-in) 1Displacement per stroke was calculated at 4.8 bar (70 psig)
air inlet pressure against a 2 bar (30 psig) head pressure.
The Efficiency Management System (EMS) can be used to optimize the performance of your Wilden pump for specific applications. The pump is delivered with the EMS adjusted to setting 4, which allows maximum flow. The EMS curve allows the pump user to deter- mine flow and air consumption at each EMS setting. For any EMS setting and discharge pressure, the “X factor” is used as a multi- plier with the original values from the setting 4 performance curve to calculate the actual flow and air consumption values for that spe- cific EMS setting. Note: you can interpolate between the setting curves for operation at intermediate EMS settings.
EXAMPLE A PX8 Saniflo HS, reduced stroke PTFE-fitted pump operating at EMS setting 4, achieved a flow rate of 257 lpm (68 gpm) using 170 Nm3/h (100 scfm) of air when run at 6.9 bar (100 psig) air inlet pres-
sure and 1.4 bar (20 psig) discharge pressure (See dot on perfor- mance curve). The end user did not require that much flow and wanted to reduce air consumption at his facility. He determined that EMS setting 1 would meet his needs. At 1.4 bar (20 psig) discharge pressure and EMS setting 1, the flow “X factor” is 0.33 and the air “X factor” is 0.21 (see dots on EMS curve).
Multiplying the original setting 4 values by the “X factors” provides the setting 1 flow rate of 85 lpm (22 gpm) and an air consumption of 36 Nm3/h (21 scfm). The flow rate was reduced by 67% while the air con-
sumption was reduced by 79%, thus providing increased efficiency.
For a detailed example for how to set your EMS, see beginning of performance curve section. Caution: Do not exceed 8.6 bar (125 psig) air supply pressure.
Flow rates indicated on chart were determined by pumping water with a vertically mounted, center ported ball check configuration. When alternate check valve options are used, multiply flow rate by appropriate factor: For optimum life and performance, pumps should be specified so that daily operation parameters fall in the center of the pump performance curve.

PERFORMANCE
PX8 HS Performance 17 WILDEN PUMP & ENGINEERING, LLC
SETTING 4 PERFORMANCE CURVE EMS CURVE
PX8 SANIFLO HS REDUCED STROKE PTFE SIPD-FITTED
(Sanitary Integrate Piston Diaphragm)
EXAMPLE A PX8 Saniflo HS, reduced stroke PTFE SIPD-fitted pump operating at EMS setting 4, achieved a flow rate of 197 lpm (52 gpm) using 93 Nm3/h (55 scfm) of air when run at 4.1 bar (60 psig) air inlet pressure and 1.4 bar (20 psig) discharge pressure (See dot on performance curve). The end user did not require that much flow and wanted to reduce air consumption at his facility. He determined that EMS setting 3 would meet his needs. At 1.4 bar (20 psig) discharge pressure and EMS setting 3, the flow “X factor” is 0.87 and the air “X factor” is 0.74 (see dots on EMS curve). Multiplying the original setting 4 values by the “X factors” provides the setting 3 flow rate of 171 lpm (45 gpm) and an air consumption of 69 Nm3/h (41 scfm). The flow rate was reduced by 13% while the air con- sumption was reduced by 26%, thus providing increased efficiency. For a detailed example for how to set your EMS, see beginning of performance curve section. Caution: Do not exceed 8.6 bar (125 psig) air supply pressure.
The Efficiency Management System (EMS) can be used to optimize the performance of your Wilden pump for specific applications. The pump is delivered with the EMS adjusted to setting 4, which allows maximum flow. The EMS curve allows the pump user to determine flow and air consumption at each EMS setting. For any EMS setting and discharge pressure, the “X factor” is used as a multiplier with the original values from the setting 4 performance curve to calculate the actual flow and air consumption values for that specific EMS setting. Note: you can interpolate between the setting curves for operation at intermediate EMS settings.
TECHNICAL DATA Height . . . . . . . . . . . . . . . . . . . . . . . . . 1008 mm (39.7”) Width. . . . . . . . . . . . . . . . . . . . . . . . . . . 460 mm (18.1”) Depth. . . . . . . . . . . . . . . . . . . . . . . . . . . 498 mm (19.6”) Ship Weight . . . . . . . . . . . . . . . . . . . . . 49 kg (109 lbs.) Air Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 mm (3/4”) Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 mm (2”) Outlet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 mm (2”) Suction Lift . . . . . . . . . . . . . . . . . . . . . . 2.3 m Dry (7.4’) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.0 m Wet (29.5’) Disp. Per Stroke. . . . . . . . . . . . . . . . . . 0.4 l (0.11 gal.)1 Max. Flow Rate . . . . . . . . . . . . . . . .405 lpm (107 gpm) Max. Size Solids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mushroom Valve . . . . . . . . . . . . . . . . . 6.4 mm (1/4”) Ball Valve. . . . . . . . . . . . . . . . . . . . . . . 12.7 mm (1/2”) Surface Finish . . . . . . . . . . . . . . . . Ra 0.8 µm (32 µ-in) 1Displacement per stroke was calculated at 4.8 bar (70 psig)
air inlet pressure against a 2 bar (30 psig) head pressure.
Flow rates indicated on chart were determined by pumping water with a vertically mounted, center ported ball check configuration. When alternate check valve options are used, multiply flow rate by appropriate factor: For optimum life and performance, pumps should be specified so that daily operation parameters fall in the center of the pump performance curve.

PERFORMANCE
WILDEN PUMP & ENGINEERING, LLC 18 PX8 HS Performance
SETTING 4 PERFORMANCE CURVE EMS CURVE
PX8 SANIFLO HS REDUCED STROKE ULTRA-FLEXTM-FITTED
EXAMPLE A PX8 Saniflo HS, reduced stroke Ultra-Flex-fitted pump operating at EMS setting 4, achieved a flow rate of 250 lpm (66 gpm) using 97 Nm3/h (57 scfm) of air when run at 4.1 bar (60 psig) air inlet pressure and 2.1 bar (30 psig) discharge pressure (See dot on performance curve). The end user did not require that much flow and wanted to reduce air consumption at his facility. He determined that EMS setting 1 would meet his needs. At 2.1 bar (30 psig) discharge pressure and EMS setting 1, the flow “X factor” is 0.34 and the air “X factor” is 0.20 (see dots on EMS curve). Multiplying the original setting 4 values by the “X factors” provides the setting 1 flow rate of 85 lpm (22 gpm) and an air consumption of 19 Nm3/h (11 scfm). The flow rate was reduced by 66% while the air consumption was reduced by 80%, thus providing increased efficiency. For a detailed example for how to set your EMS, see beginning of performance curve section. Caution: Do not exceed 8.6 bar (125 psig) air supply pressure.
The Efficiency Management System (EMS) can be used to optimize the performance of your Wilden pump for specific applications. The pump is delivered with the EMS adjusted to setting 4, which allows maximum flow. The EMS curve allows the pump user to determine flow and air consumption at each EMS setting. For any EMS setting and discharge pressure, the “X factor” is used as a multiplier with the original values from the setting 4 performance curve to calculate the actual flow and air consumption values for that specific EMS setting. Note: you can interpolate between the setting curves for operation at intermediate EMS settings.
TECHNICAL DATA Height . . . . . . . . . . . . . . . . . . . . . . . . . 1008 mm (39.7”) Width. . . . . . . . . . . . . . . . . . . . . . . . . . . 460 mm (18.1”) Depth. . . . . . . . . . . . . . . . . . . . . . . . . . . 498 mm (19.6”) Ship Weight . . . . . . . . . . . . . . . . . . . . . 49 kg (109 lbs.) Air Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 mm (3/4”) Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 mm (2”) Outlet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 mm (2”) Suction Lift . . . . . . . . . . . . . . . . . . . . . 3.8 m Dry (12.5’) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.0 m Wet (29.5’) Disp. Per Stroke. . . . . . . . . . . . . . . . . . 0.9 l (0.23 gal.)1 Max. Flow Rate . . . . . . . . . . . . . . . .534 lpm (141 gpm) Max. Size Solids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mushroom Valve . . . . . . . . . . . . . . . . . 6.4 mm (1/4”) Ball Valve. . . . . . . . . . . . . . . . . . . . . . . 12.7 mm (1/2”) Surface Finish . . . . . . . . . . . . . . . . Ra 0.8 µm (32 µ-in) 1Displacement per stroke was calculated at 4.8 bar (70 psig)
air inlet pressure against a 2 bar (30 psig) head pressure.
Flow rates indicated on chart were determined by pumping water with a vertically mounted, center ported ball check configuration. When alternate check valve options are used, multiply flow rate by appropriate factor: For optimum life and performance, pumps should be specified so that daily operation parameters fall in the center of the pump performance curve.