Wilo 490 Series User manual

A WILO BRAND
Installation and Operating Manual
490 Series SXT 3”-10”
Self-Priming Pumps

TABLE OF CONTENTS
INTRODUCTION ..................................................................................................................................... - 3 -
SAFETY SECTION A .............................................................................................................................. - 4 -
INSTALLATION SECTION B ................................................................................................................ - 5 -
Pump Dimensions ............................................................................................................................. - 6 -
PREINSTALLATION INSPECTION ........................................................................................................ - 9 -
POSITIONING PUMP .................................................................................................................................. - 9 -
Lifting ...................................................................................................................................................... - 9 -
Mounting ............................................................................................................................................... - 9 -
Clearance .............................................................................................................................................- 10 -
SUCTION AND DISCHARGE PIPING .................................................................................................- 10 -
Materials .............................................................................................................................................. - 10 -
Line Configuration .......................................................................................................................... - 10 -
Connections to Pump ................................................................................................................... - 10 -
Gauges .................................................................................................................................................. - 10 -
SUCTION LINES .........................................................................................................................................- 11 -
Fittings ................................................................................................................................................. - 11 -
Strainers ............................................................................................................................................... - 11 -
Sealing .................................................................................................................................................. - 11 -
Suction Lines In Sumps ................................................................................................................- 11 -
Suction Line Positioning .............................................................................................................. - 12 -
DISCHARGE LINES .................................................................................................................................... - 13 -
Siphoning ............................................................................................................................................- 13 -
Valves .................................................................................................................................................... - 13 -
Bypass Lines .......................................................................................................................................- 13 -
AUTOMATIC AIR RELEASE VALVE ...................................................................................................- 14 -
Theory of Operation ......................................................................................................................- 14 -
Air Release Valve Installation ....................................................................................................- 14 -
ALIGNMENT ................................................................................................................................................ - 15 -
Coupled Drives .................................................................................................................................- 16 -
Drive Belts ........................................................................................................................................... - 17 -
OPERATION SECTION C ....................................................................................................................- 18 -
PRIMING ........................................................................................................................................................- 18 -
STARTING .................................................................................................................................................... - 18 -
Rotation ...............................................................................................................................................- 18 -
OPERATION ................................................................................................................................................. - 19 -
Lines With a Bypass .......................................................................................................................- 19 -
Lines Without a Bypass ................................................................................................................- 19 -
Leakage ................................................................................................................................................- 19 -
Liquid Temperature And Overheating ..................................................................................- 19 -
Strainer Check ..................................................................................................................................- 20 -
Pump Vacuum Check ....................................................................................................................- 20 -
STOPPING .................................................................................................................................................... - 20 -
Cold Weather Preservation ........................................................................................................- 21 -
BEARING TEMPERATURE CHECK ..................................................................................................... - 21 -
TROUBLESHOOTING SECTION D
...................................................................................................- 22 -
PREVENTIVE MAINTENANCE .............................................................................................................- 23 -

- 2 -
IOM 490 SXT 3”-10”_0222
PUMP MAINTENANCE AND REPAIR SECTION E ......................................................................- 24 -
PERFORMANCE CURVE ......................................................................................................................... - 24 -
ILLUSTRATION ...........................................................................................................................................- 28 -
PARTS LIST .................................................................................................................................................. - 29 -
PUMP AND SEAL DISASSEMBLY AND REASSEMBLY ..............................................................- 29 -
Back Cover and Wear Plate Removal ..................................................................................... - 33 -
Rotating Assembly Removal .....................................................................................................- 33 -
Impeller Removal ............................................................................................................................. - 35 -
Seal Removal ..................................................................................................................................... - 35 -
Shaft and Bearing Removal and Disassembly ...................................................................- 35 -
Shaft and Bearing Reassembly and Installation ...............................................................- 36 -
Seal Installation ................................................................................................................................ - 38 -
Impeller Installation and Adjustment ....................................................................................- 41 -
Rotating Assembly Installation ................................................................................................ - 42 -
Back Cover and Wear Plate Installation and Adjustment ............................................- 43 -
PRESSURE RELIEF VALVE MAINTENANCE ...................................................................................- 45 -
Final Pump Assembly .................................................................................................................... - 45 -
LUBRICATION ............................................................................................................................................. - 46 -
Seal Assembly ...................................................................................................................................- 46 -
Bearings ............................................................................................................................................... - 46 -
Power Source ....................................................................................................................................- 46 -
WARRANTY ...........................................................................................................................................- 47 -

- 3 -
IOM 490 SXT 3”-10”_0222
INTRODUCTION
Thank You
for purchasing an American-Marsh Pump. Read this manual carefully to learn how to
safely install and operate your pump. Failure to do so could result in personal injury or damage to
the pump.
Because pump installations are seldom identical, this manual cannot possibly provide detailed
instructions and precautions for every aspect of each specific application. Therefore, it is the
responsibility of the owner/installer of the pump to ensure that applications not addressed in this
manual are performed only after establishing that neither operator safety nor pump integrity are
compromised by the installation. Pumps and related equipment must be installed and operated
according to all national, local and industry standards.
If there are any questions regarding the pump or its application which are not covered in this
manual or in other literature accompanying this unit, please contact your AMP distributor:
American-Marsh Pumps
550 E. South St.
Collierville, TN 38017
Phone: [phone]
For information or technical assistance on the power source, contact the power source
manufacturer's local dealer or representative.
RECORD YOUR PUMP MODEL AND SERIAL NUMBER
Please record your pump model and serial number in the spaces provided below.
Your American-Marsh Pumps (AMP) distributor needs this information when you require parts or service.
Pump Model:
Serial Number:

- 4 -
IOM 490 SXT 3”-10”_0222
HAZARD AND INSTRUCTION DEFINITIONS
The following are used to alert maintenance personnel to procedures which require special
attention, to those which could damage equipment, and to those which could be dangerous to
personnel:
DANGER: Immediate hazards which WILL result in severe personal injury or death. These
instructions describe the procedure required and the injury which will result from failure to
follow the procedure.
WARNING: Hazards or unsafe practices which COULD result in severe personal injury or
death. These instructions describe the procedure required and the injury which could result
from failure to follow the procedure
CAUTION: Hazards or unsafe practices which COULD result in minor personal injury or
product or property damage. These instructions describe the requirements and the possible
damage which could result from failure to follow the procedure
NOTE: Instructions to aid in installation, operation, and maintenance or which clarify a procedure.
SAFETY SECTION A
This information applies to the 490 Series SXT 3”-10” pumps. AMP has no control over or particular
knowledge of the power source which will be used. Refer to the manual accompanying the power
source before attempting to begin operation.
This manual will alert personnel to known procedures which require special attention, to those
which could damage equipment, and to those which could be dangerous to personnel. However,
this manual cannot possibly provide detailed instructions and precautions for each specific
application or for every situation that might occur during maintenance of the unit. Therefore, it is
the responsibility of the owner, installer and/or maintenance personnel to ensure that applications
and/or maintenance procedures
NOT addressed in this manual are performed ONLY after
establishing that neither personal safety
NOR pump integrity are compromised by such
applications or procedures.
This pump is designed to handle most non ‐ volatile, non ‐ flammable liquids containing
specified entrained solids. DO NOT attempt to pump volatile, corrosive, or flammable
materials which may damage the pump or endanger personnel as a result of pump
failure.
After the pump has been positioned, make certain that the pump and all piping
connections are tight, properly supported, and secure
before operation.
Do not operate the pump without the guards in place over the rotating parts. Exposed
rotating parts can catch clothing, fingers, or tools, causing severe injury to personnel.
Do not remove plates, covers, gauges, pipe plugs, or fittings from an overheated pump.
Vapor pressure within the pump can cause parts being disengaged to be ejected with great force.
Allow the pump to cool before servicing.

- 5 -
IOM 490 SXT 3”-10”_0222
Do not operate the pump against a closed discharge valve for long periods of time. If
operated against a closed discharge valve, pump components will deteriorate, and the
liquid could come to a boil, build pressure, and cause the pump casing to rupture or
explode.
Death or serious personal injury and damage to the pump or components can occur if proper
lifting procedures are not observed. Make certain that hoists, chains, slings, or cables are in good
working condition and of sufficient capacity and that they are positioned so that loads will be
balanced, and the pump or components will not be damaged when lifting. Suction and discharge
hoses and piping must be removed from the pump before lifting. Lift the pump or component
only as high as necessary and keep personnel away from suspended objects
.
INSTALLATION SECTION B
Review all SAFETY information in Section A.
Since pump installations are seldom identical, this section offers only general recommendations
and practices required to inspect, position, and arrange the pump and piping.
Most of the information pertains to a standard static lift application where the pump is positioned
above the free level of liquid to be pumped.
If installed in a flooded suction application where the liquid is supplied to the pump under pressure,
some of the information such as mounting, line configuration, and priming must be tailored to the
specific application. Since the pressure supplied to the pump is critical to performance and safety,
be sure to limit the incoming pressure to 50% of the maximum permissible operating pressure as
shown on the pump performance curve.
For further assistance, contact your AMP distributor.

- 6 -
IOM 490 SXT 3”-10”_0222
Pump Dimensions
See Figures 1 for the approximate physical dimensions of the pump model SXT 3”-10”.
OUTLINE DRAWING
SXT 3X3

- 7 -
IOM 490 SXT 3”-10”_0222
SXT 6X6

- 8 -
IOM 490 SXT 3”-10”_0222
SXT 8X8
SXT 10X10

- 9 -
IOM 490 SXT 3”-10”_0222
PREINSTALLATION INSPECTION
The pump assembly was inspected and tested before shipment from the factory. Before
installation, inspect the pump for damage which may have occurred during shipment. Check as
follows:
a.
Inspect the pump for cracks, dents, damaged threads, and other obvious damage.
b.
Check for and tighten loose attaching hardware. Since gaskets tend to shrink after drying,
check for loose hardware at mating surfaces.
c.
Carefully read all warnings and cautions contained in this manual or affixed to the pump, and
perform all duties indicated. Note the direction of rotation indicated on the pump. Check that
the pump shaft rotates counterclockwise when facing the impeller.
Only operate this pump in the direction indicated by the arrow on the pump body and on
the accompanying decal. Refer to ROTATION in OPERATION, Section C.
d. Check levels and lubricate as necessary. Refer to LUBRICATION in the MAINTENANCE AND
REPAIR section of this manual and perform duties as instructed.
e.
If the pump and power source have been stored for more than 12 months, some of the
components or lubricants may have exceeded their maximum shelf life. These must be
inspected or replaced to ensure maximum pump service.
If the maximum shelf life has been exceeded, or if anything appears to be abnormal, contact your
AMP distributor to determine the repair or updating policy. Do not put the pump into service until
appropriate action has been taken.
POSITIONING PUMP
Lifting
Pump unit weights will vary depending on the mounting and drive provided. Check the shipping tag
on the unit packaging for the actual weight, and use lifting equipment with appropriate capacity.
Drain the pump and remove all customer
‐ installed equipment such as suction and discharge hoses
or piping before attempting to lift existing, installed units.
Death or serious personal injury and damage to the pump or components can occur if
proper lifting procedures are not observed. Make certain that hoists, chains, slings or
cables are in good working condition and of sufficient capacity and that they are
positioned so that loads will be balanced, and the pump or components will not be
damaged when lifting. Suction and discharge hoses and piping must be removed from the pump
before lifting. Lift the pump or component only as high as necessary and keep personnel.
Mounting
Locate the pump in an accessible place as close as practical to the liquid being pumped. Level
mounting is essential for proper operation.
The pump may have to be supported or shimmed to provide for level operation or to eliminate
vibration.

- 10 -
IOM 490 SXT 3”-10”_0222
Clearance
Clearance recommendations for removal and access of interior pump parts.
PUMP SIZE
MINIMAL CLEARANCE FOR
REMOVAL OF FRONT COVER
RECOMMENDED CLEARANCE
FOR REMOVAL OF COVER
AND EASY ACCESS TO THE
PUMP INTERIOR
3X3
9 inches (229 mm)
18 inches (457 mm)
4X4
10 inches (254 mm)
18 inches (457 mm)
6X6
11 inches (279,4 mm)
18 inches (457 mm)
8X8
13 inches (330,2 mm)
24 inches (609.6 mm)
SUCTION AND DISCHARGE PIPING
Pump performance is adversely affected by increased suction lift, discharge elevation, and friction
losses. See the performance curve and operating range shown in
SECTION E to be sure your overall
application allows pump to operate within the safe operation range.
Materials
Either pipe or hose maybe used for suction and discharge lines; however, the materials must be
compatible with the liquid being pumped. If hose is used in suction lines, it must be the rigid
‐ wall,
reinforced type to prevent collapse under suction. Using piping couplings in suction lines is not
recommended.
Line Configuration
Keep suction and discharge lines as straight as possible to minimize friction losses. Make minimum
use of elbows and fittings, which substantially increase friction loss. If elbows are necessary, use
the long
‐ radius type to minimize friction loss.
Connections to Pump
Before tightening a connecting flange, align it exactly with the pump port. Never pull a pipeline
into place by tightening the flange bolts and/or couplings.
Lines near the pump must be independently supported to avoid strain on the pump which could
cause excessive vibration, decreased bearing life, and increased shaft and seal wear. If hose
‐ type
lines are used, they should have adequate support to secure them when filled with liquid and under
pressure.
Gauges
Most pumps are drilled and tapped for installing discharge pressure and vacuum suction gauges. If
these gauges are desired for pumps that are not tapped, drill and tap the suction and discharge
lines not less than 18 inches (457,2 mm) from the suction and discharge ports and install the lines.
Installation closer to the pump may result in erratic readings.

- 11 -
IOM 490 SXT 3”-10”_0222
SUCTION LINES
To avoid air pockets, which could affect pump priming, the suction line must be as short and direct
as possible. When operation involves a suction lift, the line must always slope upward to the pump
from the source of the liquid being pumped; if the line slopes down to the pump at any point along
the suction run, air pockets will be created.
Fittings
Suction lines should be the same size as the pump inlet. If reducers are used in suction lines, they
should be the eccentric type, and should be installed with the flat part of the reducers uppermost
to avoid creating air pockets. Valves are not normally used in suction lines, but if a valve is used,
install it with the stem horizontal to avoid air pockets.
Strainers
If a strainer is furnished with the pump, be certain to use it; any spherical solids which pass through
a strainer furnished with the pump will also pass through the pump itself.
If a strainer is not furnished with the pump, but is installed by the pump user, make certain that the
total area of the openings in the strainer is at least three or four times the cross section of the
suction line, and that the openings will not permit passage of solids larger than the solids handling
capability of the pump.
The SXT pumps are designed to handle the following solid sizes:
PUMP SIZE
MAXIMUM SOLID SIZE
3X3
2.5 inches (63,5 mm)
4X4
3 inches (76,2 mm)
6X6
3 inches (76,2 mm)
8X8
3 inches (76.2 mm)
10X10
3 inches (76.2 mm)
Sealing
Since even a slight leak will affect priming, head, and capacity, especially when operating with a
high suction lift, all connections in the suction line should be sealed with pipe dope to ensure an
air-tight seal. Follow the sealant manufacturer's recommendations when selecting and applying
the pipe dope. The pipe dope should be compatible with the liquid being pumped.
Suction Lines In Sumps
If a single suction line is installed in a sump, it should be positioned away from the wall of the sump
at a distance equal to 1 1/2 times the diameter of the suction line.
If there is a liquid flow from an open pipe into the sump, the flow should be kept away from the
suction inlet because the inflow will carry air down into the sump, and air entering the suction line
will reduce pump efficiency.

- 12 -
IOM 490 SXT 3”-10”_0222
If it is necessary to position inflow close to the suction inlet, install a baffle between the inflow and
the suction inlet at a distance 1 1/2 times the diameter of the suction pipe. The baffle will allow
entrained air to escape from the liquid before it is drawn into the suction inlet.
If two suction lines are installed in a single sump, the flow paths may interact, reducing the
efficiency of one or both pumps. To avoid this, position the suction inlets so that they are
separated by a distance equal to at least 3 times the diameter of the suction pipe.
Suction Line Positioning
The depth of submergence of the suction line is critical to efficient pump operation. Figure 2
shows recommended minimum submergence vs. velocity.
NOTE
The pipe submergence required may be reduced by installing a standard pipe increaser fitting at
the end of the suction line. The larger opening size will reduce the inlet velocity. Calculate the
required submergence using the following formula based on the increased opening size (area or
diameter).
Figure 2. Recommended Minimum Suction Line Submergence vs. Velocity

- 13 -
IOM 490 SXT 3”-10”_0222
DISCHARGE LINES
Siphoning
Do not terminate the discharge line at a level lower than that of the liquid being pumped unless a
siphon breaker is used in the line. Otherwise, a siphoning action causing damage to the pump could
result.
Valves
If a throttling valve is desired in the discharge line, use a valve as large as the largest pipe to
minimize friction losses. Never install a throttling valve in a suction line.
With high discharge heads, it is recommended that a throttling valve and a system check valve be
installed in the discharge line to protect the pump from excessive shock pressure and reverse
rotation when it is stopped.
If the application involves a high discharge head, gradually close the discharge throttling
valve before stopping the pump.
Bypass Lines
Self ‐ priming pumps are not air compressors. During the priming cycle, air from the suction line
must be vented to atmosphere on the discharge side. If the discharge line is open, this air will be
vented through the discharge. However, if a check valve has been installed in the discharge line,
the discharge side of the pump must be opened to atmospheric pressure through a bypass line
installed between the pump discharge and the check valve. A self
‐ priming centrifugal pump will
not prime if there is sufficient static liquid head to hold the discharge check valve closed.
NOTE
The bypass line should be sized so that it does not affect pump discharge capacity; however, the
bypass line should be at least 1 inch in diameter to minimize the chance of plugging.
In low discharge head applications (less than 30 feet or 9 meters), it is recommended that the
bypass line be run back to the wet well and located 6 inches below the water level or cut
‐ off point
of the low-level pump. In some installations, this bypass line may be terminated with a six
‐ to ‐
eight-foot length of 1 1/4-inch I.D. smooth ‐ bore hose; air and liquid vented during the priming
process will then agitate the hose and break up any solids, grease, or other substances likely to
cause clogging.
A bypass line that is returned to a wet well must be secured against being drawn into
the pump suction inlet. It is also recommended that pipe unions be installed at each
90°elbow in a bypass line to ease disassembly and maintenance.
In high discharge head applications (more than 30 feet), an excessive amount of liquid may be
bypassed and forced back to the wet well under the full working pressure of the pump; this will
reduce overall pumping efficiency.
Therefore, it is recommended that Automatic Air Release
Valve (ARV) be installed in the bypass line
.
Automatic Air Release Valves (ARV’s) are reliable and require minimum maintenance. See
AUTOMATIC AIR RELEASE VALVE in this section for installation and theory of operation of the
Automatic Air Release Valve.

- 14 -
IOM 490 SXT 3”-10”_0222
If the installation involves a flooded suction such as a below ‐ ground lift station. A pipe union and
manual shut
‐ off valve may be installed in the bleed line to allow service of the valve without
shutting down the station, and to eliminate the possibility of flooding. If a manual shut
‐ off valve is
installed anywhere in the air release piping, it must be a full
‐ opening ball type valve to prevent
plugging by solids.
If a manual shut ‐ off valve is installed in a bypass line, it must not be left closed during
operation. A closed manual shut
‐ off valve may cause a pump which has lost prime to
continue to operate without reaching prime, causing dangerous overheating and
possible explosive rupture of the pump casing. Personnel could be severely injured.
Allow an over ‐ heated pump to cool before servicing. Do not remove plates, covers, gauges, or
fittings from an over
‐ heated pump. Liquid within the pump can reach boiling temperatures, and
vapor pressure within the pump can cause parts being disengaged to be ejected with great force.
After the pump cools, drain the liquid from the pump by removing the casing drain plug. Use
caution when removing the plug to prevent injury to personnel from hot liquid.
AUTOMATIC AIR RELEASE VALVE
Theory of Operation
When properly installed, an Automatic Air Release Valve (ARV) will permit air to escape through the
bypass line and then close automatically when the pump is fully primed and pumping at full
capacity.
Some leakage (1 to 5 gallons [3.8 to 19 liters] per minute) will occur when the valve is
fully closed. Be sure the bypass line is directed back to the wet well or tank to prevent
hazardous spills
*
Consult the manual accompanying the Air Release Valve for additional information on valve
installation and performance.
Air Release Valve Installation
The Automatic Air Release Valve must be independently mounted in a horizontal position between
the pump discharge port and the inlet side of the discharge check valve (see
Figure 3 ).

- 15 -
IOM 490 SXT 3”-10”_0222
Figure 3. Typical Automatic Air Release Valve Installation
Connect the valve outlet to a bleed line which slopes back to the wet well or sump. The bleed line
must be the same size as the outlet opening or larger, depending on which Air Release Valve is
being used. If piping is used for the bleed line, avoid the use of elbows whenever possible.
NOTE
For multiple pump installations, it is recommended that each Air Release Valve be fitted with an
independent bleeder line directed back to the wet well. If multiple Air Release Valves are installed in
a system,
DO NOT direct bleeder lines to a common manifold pipe.
ALIGNMENT
The alignment of the pump and its power source is critical for trouble ‐ free mechanical operation. In
either a flexible coupling or V
‐ belt driven system, the driver and pump must be mounted so that
their shafts are aligned with and parallel to each other. It is imperative that alignment be checked
after the pump and piping are installed, and before operation.
NOTE
Check
Rotation , Section C , before final alignment of the pump.
When mounted at the AMP factory, driver and pump are aligned before shipment. Misalignment will

- 16 -
IOM 490 SXT 3”-10”_0222
occur in transit and handling. Pumps must be checked and realigned before operation. Before
checking alignment, tighten the foundation bolts. The pump casing feet and/or pedestal feet, and
the driver mounting bolts should also be tightly secured.
When checking alignment, disconnect the power source to ensure that the pump will
remain inoperative.
Adjusting the alignment in one direction may alter the alignment in another direction.
check each procedure after altering alignment
.
Coupled Drives
When using couplings, the axis of the power source must be aligned to the axis of the pump shaft
in both the horizontal and vertical planes. Most couplings require a specific gap or clearance
between the driving and the driven shafts. Refer to the coupling manufacturer's service literature.
Figure 4. Aligning Spider Type Couplings
Figure 5. Aligning Non-Spider Type Couplings
Align spider insert type couplings by using calipers to measure the dimensions on the
circumference of the outer ends of the coupling hub every 90°. The coupling is in alignment when
the hub ends are the same distance apart at all points (see
Figure 4 ).
Align non
‐ spider type couplings by using a feeler gauge or taper gauge between the coupling
halves every 90°. The coupling is in alignment when the hubs are the same distance apart at all
points (see
Figure 5 ).

- 17 -
IOM 490 SXT 3”-10”_0222
Check parallel adjustment by laying a straightedge across both coupling rims at the top, bottom,
and side. When the straightedge rests evenly on both halves of the coupling, the coupling is in
horizontal parallel alignment. If the coupling is misaligned, use a feeler gauge between the coupling
and the straightedge to measure the amount of misalignment.
Drive Belts
When using drive belts, the power source and the pump must be parallel. Use a straightedge along
the sides of the pulleys to ensure that the pulleys are properly aligned (see
Figure 6 ). In drive
systems using two or more belts, make certain that the belts are a matched set; unmatched sets
will cause accelerated belt wear.
MISALIGNED:
SHAFTS NOT PARALLEL
MISALIGNED:
SHAFTS NOT IN LINE
ALIGNED:
SHAFTS PARALLEL AND SHEAVES
IN LINE
Figure 6. Alignment of V ‐ Belt Driven Pumps
Tighten the belts in accordance with the belt manufacturer's instructions. If the belts are too loose,
they will slip; if the belts are too tight, there will be excessive power loss and possible bearing
failure. Select pulleys that will match the proper speed ratio; over speeding the pump may damage
both pump and power source.
Do not operate the pump without the guard in place over the rotating parts. Exposed
rotating parts can catch clothing, fingers, or tools, causing severe injury to personnel.
DRIVE BELT TENSIONING
General Rules of Tensioning
For new drive belts, check the tension after 5, 20 and 50 hours of operation and re ‐ tension as
required (see the following procedure for measuring belt tension). Thereafter, check and re
‐ tension
if required monthly or at 500-hour intervals, whichever comes first.
Ideal drive belt tension is the lowest tension at which the belt will not slip under peak load
conditions. Do not over
‐ tension drive belts. Over ‐ tensioning will shorten both drive belt and
bearing life. Under
‐ tensioning will cause belt slippage. Always keep belts free from dirt, grease, oil,
and other foreign material which may cause slippage.

- 18 -
IOM 490 SXT 3”-10”_0222
OPERATION SECTION C
Review all SAFETY information in Section A.
Follow the instructions on all tags, labels and decals attached to the pump.
This pump is designed to handle liquids containing large, entrained solids and slurries.
Do not attempt to pump volatile, corrosive, or flammable liquids which may damage
the pump or endanger personnel as a result of pump failure.
Pump speed and operating conditions must be within performance range shown in
SECTION E.
PRIMING
Install the pump and piping as described in the INSTALLATION section. Make sure that the piping
connections are tight, and that the pump is securely mounted. Check that the pump is properly
lubricated (see
LUBRICATION in MAINTENANCE AND REPAIR ).
This pump is self
‐ priming, but the pump should never be operated unless there is liquid in the
pump casing.
Never operate this pump unless there is liquid in the pump casing. The pump will not
prime when dry. Extended operation of a dry pump will destroy the seal assembly.
Add liquid to the pump casing when:
1.
The pump is being put into service for the first time.
2.
The pump has not been used for a considerable length of time.
3. The liquid in the pump casing has evaporated.
Once the pump casing has been filled, the pump will prime and reprime as necessary.
After filling the pump casing, reinstall and tighten the fill plug. Do not attempt to
operate the pump unless all connecting piping is securely installed. Otherwise, liquid in
the pump forced out under pressure could cause injury to personnel.
To fill the pump, remove the pump casing fill cover or fill plug in the top of the casing, and add
clean liquid until the casing is filled. Replace the fill cover or fill plug before operating the pump.
STARTING
Consult the operations manual furnished with the power source.
Rotation
The correct direction of pump rotation is counterclockwise when facing the impeller. The pump
could be damaged, and performance adversely affected by incorrect rotation. If pump performance

- 19 -
IOM 490 SXT 3”-10”_0222
is not within the specified limits (see the curve on page SECTION E ), check the direction of power
source rotation before further troubleshooting.
If an electric motor is used to drive the pump, remove V
‐ belts, couplings, or otherwise disconnect
the pump from the motor before checking motor rotation. Operate the motor independently while
observing the direction of the motor shaft, or cooling fan.
If rotation is incorrect on a three
‐ phase motor, have a qualified electrician interchange any two of
the three phase wires to change direction. If rotation is incorrect on a single
‐ phase motor, consult
the literature supplied with the motor for specific instructions.
OPERATION
Lines With a Bypass
If an Automatic Air Release Valve has been installed, the valve will automatically open to allow the
pump to prime, and automatically close after priming is complete (see
INSTALLATION for Air
Release Valve operation).
If the bypass line is open, air from the suction line will be discharged through the bypass line back
to the wet well during the priming cycle. Liquid will then continue to circulate through the bypass
line while the pump is in operation.
Lines Without a Bypass
Open all valves in the discharge line and start the power source. Priming is indicated by a positive
reading on the discharge pressure gauge or by a quieter operation. The pump may not prime
immediately because the suction line must first fill with liquid. If the pump fails to prime within five
minutes, stop it and check the suction line for leaks.
After the pump has been primed, partially close the discharge line throttling valve in order to fill the
line slowly and guard against excessive shock pressure which could damage pipe ends, gaskets,
sprinkler heads, and any other fixtures connected to the line. When the discharge line is completely
filled, adjust the throttling valve to the required flow rate.
Do not operate the pump against a closed discharge throttling valve for long periods of
time. If operated against a closed discharge throttling valve, pump components will
deteriorate, and the liquid could come to a boil, build pressure, and cause the pump
casing to rupture or explode.
Leakage
No leakage should be visible at pump mating surfaces, or at pump connections or fittings. Keep all
line connections and fittings tight to maintain maximum pump efficiency.
Liquid Temperature and Overheating
The
maximum liquid temperature for this pump is 160°F (71°C). Do not apply it at a higher
operating temperature.
Overheating can occur if operated with the valves in the suction or discharge lines closed.
Operating against closed valves could bring the liquid to a boil, build pressure, and cause the pump
to rupture or explode. If overheating occurs, stop the pump, and allow it to cool before servicing it.
Refill the pump casing with cool liquid.