Wine racks America Double Deep Wine Cellar Kit User manual

Tools For Assembly:
Questions?
Toll free 1-888-373-6057 or visit WineRacksAmerica.com
ASSEMBLY INSTRUCTIONS
Double Deep Wine Cellar Kits (All Models)
Thank you and CONGRATULATIONS for
purchasing this quality product. Properly
assembled, your racking will beautifully
enhance your wine collection for many
years to come. To assemble, please check
to ensure all necessary parts are included
and follow the assembly instructions
closely. If you have any questions or
problems please call customer service toll
free 1-888-373-6057 Monday through
Friday 7:00 am - 5:00pm MST.
Planning to stain?
For best results we recommend you
stain or finish your racking BEFORE
assembly.
Cordless Drill Utility Knife
OR +
Finish Nailer
PARTS LIST PARTS ARE NOT TO SCALE
Screwdriver
Hammer Nail Setter
PARTS LIST PARTS ARE NOT TO SCALE
END LADDER ASSEMBLIES
SIDE VIEW
77 1/8"
STANDARD COLUMN CONNECTORS
(Various Lengths)
SIDE VIEW
SCREWLESS COLUMN CONNECTORS
(Various Lengths)
SIDE VIEW
The instructions pictured are for a 6 column double deep rack. Follow the same steps for
all double deep wine cellar racks , regardless of model.
1" WOOD SCREWS
FINISH NAILS
SMALL BAG OF
WOOD PUTTY
MIDDLE LADDER ASSEMBLIES
SIDE VIEW
77 1/8"

1. Find an open, flat area in which to work. Carefully remove all components from the box and remove banding
with a utility knife. Check the parts list to verify package contents
2. Arrange the end ladders on the floor so that the bottle support pieces face one another. Align the large gaps on each
end ladder. The end with the larger gap is the top of your rack. Attach a standard column connector to the top
and bottom of your rack using the 1" screws provided. Make sure the connectors are flush with the top and bottom
of your rack. (figure 1)
* Minimize the risk of splitting your ladders by
drilling a 1/16" pilot hole before driving the
wood screws. For best results, drive the screw
most of the way in with your drill, then finish
tightening by hand.
MIDDLE END STANDARD SCREWLESS 1" FINISH
RACK LADDERS LADDERS CONNECTORS CONNECTORS SCREWS NAILS
10 column 9 2 (6) 10 column (2) 10 column 66 22
9 column 8 2 (6) 9 column (2) 9 column 60 20
8 column 7 2 (6) 8 column (2) 8 column 54 18
7 column 6 2 (6) 7 column (2) 7 column 48 16
6 column 5 2 (6) 6 column (2) 6 column 42 14
5 column 4 2 (6) 5 column (2) 5 column 36 12
4 column 3 2 (6) 4 column (2) 4 column 30 10
3 column 2 2 (6) 3 column (2) 3 column 24 8
2 column 1 2 (6) 2 column (2) 2 column 18 6
1 column 0 2 (6) 1 column (2) 1 column 12 4
PACKAGE CONTENTS
* Please verify that you have the correct number of parts before proceeding. Depending on the model you purchased,
your bundle should contain the following:
* All models follow the same assembly procedure - varying only in the number of middle ladders your rack will require.
* PLEASE FOLLOW WRITTEN INSTRUCTIONS CAREFULLY
Top of rack
1
BEGIN WITH BACK
OF RACK

5. Flip rack over and secure a standard column
connector to the top and bottom of your rack
using the 1" screws provided. (gure 3)
3. Insert the middle ladders and nish securing the top & bottom connectors using the 1" screws provided.
4. Attach the middle standard connectors so that the top edge of the lower connector is 26 5/8" from the bottom
of the rack, and the top edge of the upper connector is 51 3/4" from the bottom of the rack. Secure the middle
connectors using the 1" screws provided. This is the back of your rack. (gure 2)
26 5/8"
51 3/4"
Back of rack
2
FINISH SECURING BACK
CONNECTORS
3
FRONT OF RACK

6. Attach the middle screwless connectors so that the top edge of the lower connector is 26 5/8" from the bottom
of the rack, and the top edge of the upper connector is 51 3/4" from the bottom of the rack. Make sure the rack
is flat on the floor while attaching the screwless connectors. (figure 4)
Secure the screwless connectors using a finish nail gun to drive a finish nail through the connector into each
vertical ladder. (figure 5)
If you do not have a finish nail gun, drive one of the provided finish nails into each vertical ladder until it is flush.
Then, countersink the nail using a nail setter until the head of the nail is about 1/16" below the surface of the wood.
Once again thank you for your business. Remember,
customer service is available to answer your questions
M-F 7:00 am - 5:00 pm MST. Please feel free to contact
us for any wine storage need.
360 N 700 W suite F • North Salt Lake, UT 84054
(toll free)
888-373-6057
(fax) 801-936-0534
WineRacksAmerica.com
7. Fill the nail holes using the wood putty provided. Simply push
the putty into each hole using your thumb and wipe excess
putty off the surface using a damp cloth.
8. That’s it! Enjoy this beautiful rack with your favorite beverage.
Pair with other rack styles for an ultimate cellar storage look.
1. Put the rack in the desired location.
2. Shim the front of the rack so it is
even with the back wall.
3. Locate a wall stud behind the rack.
4. Drive a 2 1/2" wood screw through a
back connector to attach to the stud.
1. Use "L" brackets (located at any
hardware store).
2. Attach to both the rack and the wall
in any out of the way spot.
Attaching your rack to the wall:
Depending on how many bottles you store, your
wine cellar rack could weigh as much as 600 lbs.
To avoid tipping attach your racking to the wall
using one of the following methods.
- OR -
4
ATTACH SCREWLESS
CONNECTORS
or
finish nail
(included)
5
SECURE WITH
FINISH NAILS