ICW TITAN ELITE T2E12P-WT2-KUB User manual
TITAN ELITE WALL MOUNT INsTALLATION
TITAN ELITE EASY-TO-WIRE WALL MOUNT INSTALLATION - 09/01/16 pjmPage 1 of 4
ICW recommends wood or metal stud mounting only.
MAXIMUM LOAD CAPACITY:
28 LBS (12.7 KG)
attempt to adjust the arm until all components
are mounted (monitor, keyboard, etc.)
(extended)
before adjusting the arm’s tension. Failure to do so will
damage the arm and void the warranty.
Doing so will cause the arm to immediately
come apart with tremendous force, and could cause
serious injury.
• If equipment requiring AC power is mounted to this unit,
haveacertiedelectricianinspecttheinstallation.
• Failure to install this unit according to these instructions
will void all ICW warranties. If installed incorrectly, ICW
is not liable for any damage or injury caused by the unit.
DANGER!
IMPORTANT
Improved cable
management.
Wires run through
the joints and are
more enclosed.
MOUNT TO WALL TRACK
Attach wall track to wall using installation
instructions provided with track.
Attach wall plate to track
Slide track adapters into track from either top or
bottom. Position wall ear to desired location on track.
Firmly tighten wall ear screws with 5/32” hex key.
Using the 3/16 hex key
provided, attach wall plate
to ear with four 1/4-20
screws provided.
Attach track adapters
Attach track adapters
to back of wall ear by
threading1/4x20athead
socket head screws from
front of wall ear into track
adapters. Attach loosely
with 5/32” hex key.
MOUNT WALL EAR & PLATE
T2E12P-WT2-KUB
WALL MOUNT
Othercongurations
available
Wall Track Mount
Using the 3/16 hex key
provided, attach wall plate
to ear with four 1/4-20
screws provided.
Locate stud and mark top
hole, drill 11/64 pilot hole
and insert #14 screw and
tighten slightly. Using a
level, mark lower holes and
drill pilot holes. Insert #14
screws and, with unit level,
tighten all screws.
NOTE: ICW supplies #14
wood screws. If installing
onto metal studs, you will
need to replace with proper
metal stud fasteners.
MOUNT WALL EAR & PLATE
Wall Mount
TITAN ELITE WALL MOUNT INsTALLATION
TITAN ELITE EASY-TO-WIRE WALL MOUNT INSTALLATION - 09/01/16 pjmPage 2 of 4
ATTACH VEsA
Attach VESA to
monitor using four
4mm screws in the
hardware bag.
Mount the VESA
assembly by
screwing the knob
through the rail
into the VESA.
Attach & Adjust Monitor Attach Keyboard Tray
Attach the Paralink
Keyboard Mount to the
Monitor Mount by using
the 3/8-16 screw and
lock washer provided.
ATTACH PARALINK KEYBOARD TO MONITOR
• Remove screws from
drop extension using
5/32” hex key.
• Align holes in keyboard
tray with screw holes in
drop extension.
• Attach keyboard tray
using the provided
screws.
ATTACH FLIP UP KEYBOARD
• Remove beauty cap on
Paralink.
• Remove screw using 3/16”
hex key.
• Slide keyboard tray into
Paralink.
• Replace screw and tighten.
• Replace beauty cap.
Beauty cap
Screw
ATTACH KEYBOARD TO PARALINK
ADJUsT BALL VEsA TENsION & HEIGHT
Use the slider knob to
loosen the slider to adjust
the height of the monitor on
the Paralink.
Adjust the pivot tension of
the ball by gently and evenly
tightening or loosening the
four screws on the back of
the ball VESA.
Pivot tension
adjustment
screws
Slider knob
MONITOR TILT, ROTATION & ADJUsT MONITOR DEPTH
MONITOR TILT
& ROTATE
Gently hold sides of
monitor. Tilt and rotate
to desired position
with ball VESA.
ADJUST MONITOR DEPTH FOR
PARALINK: Loosen adjustment
knob, move Paralink forward or
back, then re-tighten the knob.
FOR 110 MONITOR MOUNT: Loosen
adjustment handles, move to
desired position and retighten
handles.
Adjustment
knob
Adjustment
handles
Torque Chart- In/lbs 2/23/2016
Minimum torque values Monitor Mount
Arm
Base
Mount Arm Joint Paralink EV710 Ultra
021-021-021etilE
021-021021021etilE2T
Titan (T2) 120 120 120 - 120
02158021021021artlU
UL180 / UL182 120 120 - 85 -
MD Arm 140 - 120 - 120
TITAN ELITE WALL MOUNT INsTALLATION
TITAN ELITE EASY-TO-WIRE WALL MOUNT INSTALLATION - 09/01/16 pjmPage 3 of 4
Cord Management - Wall Mount
PREss WIREs INTO CHANNEL OF ELITE ARM sECTION
After feeding the wires through
the Titan (upper) section of
the arm, press them into the
channels of the Elite (lower)
section.
Use wire clips to secure them.
Be sure wires don’t bind
and the arm moves freely.
Wire clip
FEED WIRE THROUGH TITAN ARM
Pull wires one at a time through the arm. Feed the
largestwirerst,allowingenoughslacksothearm
turns freely.
Feedtherstwirethroughthewallearandout
oftherstwireport.Feedthewirebackdown
throughtherstwireportandthroughtheTitan
arm segment. Feed the wire up and out of the
second wire port, back down and into the
Elite section of the arm.
Repeat these steps with the second wire.
Wires run through
the joints.
REPLACE ARM COVERs
Before reattaching arm
covers, slip wires through
end cover port.
Reattach black plastic
bushing around exiting
wires.
Replace covers on the Elite
section of the arm. DO NOT
use a power tool to replace
screws.
REMOVE ELITE ARM COVERs & TITAN ARM CAPs
END COVERS
Remove the end covers by unscrewing the two 3/4”
long10-24atheadscrewsusingaPhillipshead
screwdriver.
TOP COVER
Remove the long arm cover by unscrewing the two
1/4”long6-32atheadscrewsinthecenterofthe
cover using a Phillips head screwdriver. If you
use a power tool, be very careful not to strip the
screws. The arm needs to be in a
vertical position to remove
the long top cover.
TITAN ARM CAPS
Slide off the plastic caps
that cover the wire ports
on the Titan section of
the arm.
TITAN ELITE WALL MOUNT INsTALLATION
TITAN ELITE EASY-TO-WIRE WALL MOUNT INSTALLATION - 09/01/16 pjmPage 4 of 4
ADJUsT ROTATION sTOPs
Rotation limits for the
arm are set by placing
stop pins in the holes
where you want the
arm to stop. The stop
pins can be removed
and set by hand.
Rotation
Limiter Ring
Stop Pin
ADJUsT ARM REsIsTANCE
Extend the arm
straight out as shown
before adjusting the arm’s
resistance. Be sure all equipment
is mounted on the arm before
adjusting. Use the T-handle provided
to adjust the arm’s resistance.
Other ICW Rack & Stand manuals
